NEC PX-50XM5A 42XM4/50XM5/61XM4 UM - Page 34

Information Ⅵ AUTO ID settings ON: Enables Auto ID function. In the case shown below, display 1 will be set as ID 1, display 2 as ID2, etc. This can be set only when a 2×2 or 3×3 video wall is selected. REMOTE IN No.1 No.2 No.4 No.3 Display 1 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 Display 2 REMOTE OUT REMOTE OUT No.1 No.2 No.4 No.3 Display 4 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 REMOTE IN Display 3 OFF: Disables Auto ID function. IMAGE ADJUST The position of the image can be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position On "VIDEO WALL" menu, select "IMAGE ADJUST", then press the MENU/ENTER button. The "IMAGE ADJUST" screen appears. On "V-POSITION" of "IMAGE ADJUST" menu, adjust the position. IMAGE ADJUST ASPECT MODE : NORMAL V-POSITION H-POSITION V-HEIGHT H-WIDTH AUTO PICTURE : OFF FINE PICTURE PICTURE ADJ. SEL. ADJ. EXIT RETURN : ±0 : ±0 : 0 : 0 : 0 : 0 V-POSITION : +64 Information Ⅵ IMAGE ADJUST settings These are the same functions as the IMAGE ADJUST menu on page En-22. P. ON DELAY (Power on delay) Use this function to activate power-on delay. Turn on the AUTO ID before the following operations. Example: Setting "ON" MODE2: Turns on the main power of each display more delayed. * Once this function has been set to "ON", the POWER ON/OFF button on the remote control does not function except for the No.1 monitor. By pressing the POWER ON button on the remote control the No.1 monitor will turn on and the others will be turned on one by one automatically. * From the second monitor onward, neither the POWER button on the unit nor the POWER ON button on the remote control works. However, by pressing and holding the POWER ON button for more than 3 seconds, the monitor will be turned on. PLE LINK Use this function to set a uniform brightness for each display. Turn on the AUTO ID and set the DIVIDER (at 1, 4 or 9) before the following operations. Example: Setting "ON" On "PLE LINK" of "VIDEO WALL" menu, select "ON", then press the MENU/ENTER button. VIDEO WALL DIVIDER : 1 POSITION DISP. MODE : SPLIT AUTO ID : OFF IMAGE ADJUST P. ON DELAY : OFF PLE LINK : ON REPEAT TIMER : OFF SEL. ADJ. EXIT RETURN Information Ⅵ PLE LINK settings ON: Sets a uniform brightness for each screen in a video wall. This can be set only when a 2×2 or 3×3 video wall is selected. OFF: Sets the individual screen brightness for each screen in a video wall. * When this function is set "ON", connect your plasma displays with the remote cable (optional) in the order of the position numbers for the 2×2 video wall. See the drawing below. * If there are changes in the DIVIDER or POSITION, the PLE LINK will automatically turn OFF. On "P. ON DELAY" of "VIDEO WALL" menu, select "ON". VIDEO WALL DIVIDER : 1 POSITION DISP. MODE : SPLIT AUTO ID : OFF IMAGE ADJUST P. ON DELAY : ON PLE LINK : OFF REPEAT TIMER : OFF SEL. ADJ. EXIT RETURN Information Ⅵ P. ON DELAY settings ON: Turns on the main power of each display after a delay time. OFF: Turns on the main power of all displays at the same time. REMOTE IN No.1 No.2 No.4 No.3 Display 1 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 Display 2 REMOTE OUT REMOTE OUT No.1 No.2 No.4 No.3 Display 4 REMOTE OUT REMOTE IN No.1 No.2 No.4 No.3 REMOTE IN Display 3 * With the 3×3 video wall, connect the final display to the first display the same way as with 2×2 video wall. Note: The remote control can be operated unless the IR REMOTE is set to "OFF". (Only for 4×4 and 5×5 video wall modes) MODE1: Turns on the main power of each display delayed. En-33