Netgear DG834Gv5 DG834Gv5 Reference Manual - Page 81

Table 5-2., LAN IP Setup, Change the settings. For more information, see, Click, to save the changes.

Get Netgear DG834Gv5 - 54 Mbps Wireless ADSL Firewall Modem PDF manuals and user guides View all Netgear DG834Gv5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Wireless ADSL2+ Modem Router DG834G User Manual 2. Change the settings. For more information, see Table 5-2, "Using the Modem Router as a DHCP Server" on page 5-6 or "Defining Reserved IP Addresses" on page 5-7. 3. Click Apply to save the changes. The LAN TCP/IP Setup parameters are explained in the following table. Table 5-2. LAN IP Setup Settings LAN TCP/IP Setup IP Address IP Subnet Mask RIP Direction RIP Version DHCP Server For more information, see "Using the Modem Router as a DHCP Server" on page 5-6. Use Router as a DHCP Server Starting IP Address Ending IP Address Description The LAN IP address of the modem router. The LAN subnet mask of the modem router. Combined with the IP address, the IP Subnet Mask allows a device to know which other addresses are local to it, and which must be reached through a gateway or modem router. RIP (Router Information Protocol) allows a modem router to exchange routing information with other routers. This setting controls how the modem router sends and receives RIP packets. Both is the default. • Both or Out Only. The modem router broadcasts its routing table periodically. • Both or In Only. The modem router incorporates the RIP information that it receives. • None. The modem router will not send any RIP packets and will ignore any RIP packets received. This controls the format and the broadcasting method of the RIP packets that the modem router sends. It recognizes both formats when receiving. By default, this is RIP-1. • RIP-1 is universally supported. It is adequate for most networks, unless you have an unusual network setup. • RIP-2 carries more information. Both RIP-2B and RIP-2M send the routing data in RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses multicasting. This check box is usually selected so that the modem router functions as a Dynamic Host Configuration Protocol (DHCP) server. See "Using the Modem Router as a DHCP Server" on page 5-6. Specify the start of the range for the pool of IP addresses in the same subnet as the modem router. Specify the end of the range for the pool of IP addresses in the same subnet as the modem router. Advanced Configuration 5-5 v1.0, May 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
Wireless ADSL2+ Modem Router DG834G User Manual
Advanced Configuration
5-5
v1.0, May 2008
2.
Change the settings. For more information, see
Table 5-2
,
“Using the Modem Router as a
DHCP Server” on page 5-6
or
“Defining Reserved IP Addresses” on page 5-7
.
3.
Click
Apply
to save the changes.
The LAN TCP/IP Setup parameters are explained in the following table.
Table 5-2.
LAN IP Setup
Settings
Description
LAN TCP/IP
Setup
IP Address
The LAN IP address of the modem router.
IP Subnet Mask
The LAN subnet mask of the modem router. Combined with
the IP address, the IP Subnet Mask allows a device to know
which other addresses are local to it, and which must be
reached through a gateway or modem router.
RIP Direction
RIP (Router Information Protocol) allows a modem router to
exchange routing information with other routers. This
setting controls how the modem router sends and receives
RIP packets.
Both
is the default.
•
Both
or
Out Only
. The modem router broadcasts its
routing table periodically.
•
Both
or
In Only
. The modem router incorporates the RIP
information that it receives.
•
None
. The modem router will not send any RIP packets
and will ignore any RIP packets received.
RIP Version
This controls the format and the broadcasting method of the
RIP packets that the modem router sends. It recognizes
both formats when receiving. By default, this is
RIP-1
.
•
RIP-1 is universally supported. It is adequate for most
networks, unless you have an unusual network setup.
•
RIP-2 carries more information. Both RIP-2B and RIP-2M
send the routing data in RIP-2 format. RIP-2B uses
subnet broadcasting. RIP-2M uses multicasting.
DHCP Server
For more
information, see
“Using the
Modem Router
as a DHCP
Server” on
page 5-6
.
Use Router as a DHCP
Server
This check box is usually selected so that the modem router
functions as a Dynamic Host Configuration Protocol
(DHCP) server. See
“Using the Modem Router as a DHCP
Server” on page 5-6
.
Starting IP Address
Specify the start of the range for the pool of IP addresses in
the same subnet as the modem router.
Ending IP Address
Specify the end of the range for the pool of IP addresses in
the same subnet as the modem router.