Netgear DGN2000 DGN2000 Reference Manual - Page 32

Turn Access Control On, Apply, Preparing, Your Network in Appendix B - access point

Get Netgear DGN2000 - Wireless Router PDF manuals and user guides
UPC - 606449058727
View all Netgear DGN2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Wireless-N ADSL2+ Modem Router DGN2000 Reference Manual Note: The SSID of any wireless access adapters must match the SSID you specify in the modem router. If they do not match, you will not get a wireless connection. 4. Select the region in which the wireless interface will operate. 5. Set the channel if necessary. The default channel is 11. This field determines which operating frequency will be used. It should not be necessary to change the wireless channel unless you notice interference problems with another nearby wireless router or access point. Select a channel that is not being used by any other wireless networks within several hundred feet of your modem router. For more information about the wireless channel frequencies, see the online document that you can access from "Preparing Your Network" in Appendix B. Note: Up to 270Mbps mode uses two channels, but in this mode only the first channel is listed in the channel pulldown menu. The associated channels in this mode are: 1+5, 2+6, 3+7, 4+8, 5+9, 6+10, and 7+11. When you select another wireless network mode, the channel pulldown displays all available channels: 1 through 13. However, available wireless channels depend on the selected wireless region. 6. For initial configuration and test, leave the Wireless Card Access List set to allow everyone access by making sure that Turn Access Control On is not selected in the Wireless Station Access List. In addition, leave the encryption strength set to None. 7. Click Save to save your settings or click Apply to allow your changes to take effect immediately. 8. Configure and test your computers for wireless connectivity. Program the wireless adapter of your computers to have the same SSID and channel that you specified in the router. Check that they have a wireless link and can obtain an IP address by DHCP from the modem router. Once your computers have basic wireless connectivity to the modem router, you can configure the advanced wireless security functions of the firewall. 2-6 Configuring Your Wireless Network and Security Settings v1.0, July 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Wireless-N ADSL2+ Modem Router DGN2000 Reference Manual
2-6
Configuring Your Wireless Network and Security Settings
v1.0, July 2008
4.
Select the region in which the wireless interface will operate.
5.
Set the channel if necessary. The default channel is 11.
This field determines which operating frequency will be used. It should not be necessary to
change the wireless channel unless you notice interference problems with another nearby
wireless router or access point. Select a channel that is not being used by any other wireless
networks within several hundred feet of your modem router. For more information about the
wireless channel frequencies, see the online document that you can access from
“Preparing
Your Network” in Appendix B
.
6.
For initial configuration and test, leave the Wireless Card Access List set to allow everyone
access by making sure that
Turn Access Control On
is not selected in the Wireless Station
Access List. In addition, leave the encryption strength set to
None
.
7.
Click
Save
to save your settings or click
Apply
to allow your changes to take effect
immediately.
8.
Configure and test your computers for wireless connectivity.
Program the wireless adapter of your computers to have the same SSID and channel that you
specified in the router. Check that they have a wireless link and can obtain an IP address by
DHCP from the modem router.
Once your computers have basic wireless connectivity to the modem router, you can configure the
advanced wireless security functions of the firewall.
Note:
The SSID of any wireless access adapters must match the SSID you specify in
the modem router. If they do not match, you will not get a wireless connection.
Note:
Up to 270Mbps mode uses two channels, but in this mode only the first chan-
nel is listed in the channel pulldown menu. The associated channels in this
mode are: 1+5, 2+6, 3+7, 4+8, 5+9, 6+10, and 7+11. When you select another
wireless network mode, the channel pulldown displays all available channels:
1 through 13. However, available wireless channels depend on the selected
wireless region.