Netgear GS108T GS108T Setup Manual - Page 27

IP Access List, IEEE 802.1x Port Based Authentication State Settings - jumbo frames

Get Netgear GS108T - ProSafe - Gigabit Smart Switch PDF manuals and user guides
UPC - 606449051377
View all Netgear GS108T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

GS108T Smart Switch Software Administration Manual • Radius Server • TIME • LLDP Settings • Logs Configuration • PORT Status • IEEE 802.1P QOS Status • Port Based VLAN Settings • IEEE 802.1Q PVID • Link Aggregation • Monitor • Jumbo Frame Setting • Jumbo Frame Disabled • Rate Limiting • Storm Control • IEEE802.1W RSTP Setting • RSTP Function Disabled • SNMP Setting • IGMP Snooping Settings • Dynamic Multicast Entry Table • Unknown Multicast Settings • IEEE 802.1x Port Based Authentication State Settings • Port Security Settings • Trusted MAC Settings IP Access List The IP Access List page allows you to limit the IP addresses that can access the management portion of the switch. The switch will only respond to requests from computers with an IP address in the list, so include your IP address with their corresponding subnet mask to set this feature. 1. Click IP Access List in the blue navigation panel. A screen similar to that shown below appears. Managing System Settings 3-3 v1.0, May 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
GS108T Smart Switch Software Administration Manual
Managing System Settings
3-3
v1.0, May 2007
•
Radius Server
•
TIME
•
LLDP Settings
•
Logs Configuration
•
PORT Status
•
IEEE 802.1P QOS Status
•
Port Based VLAN Settings
•
IEEE 802.1Q PVID
•
Link Aggregation
•
Monitor
•
Jumbo Frame Setting
•
Jumbo Frame Disabled
•
Rate Limiting
•
Storm Control
•
IEEE802.1W RSTP Setting
•
RSTP Function Disabled
•
SNMP Setting
•
IGMP Snooping Settings
•
Dynamic Multicast Entry Table
•
Unknown Multicast Settings
•
IEEE 802.1x Port Based Authentication State Settings
•
Port Security Settings
•
Trusted MAC Settings
IP Access List
The IP Access List page allows you to limit the IP addresses that can access the management
portion of the switch. The switch will only respond to requests from computers with an IP address
in the list, so include your IP address with their corresponding subnet mask to set this feature.
1.
Click
IP Access List
in the blue navigation panel. A screen similar to that shown below
appears.