Panasonic AG-UX90 AG-UX90 Operating Instructions
Panasonic AG-UX90 Manual
 |
View all Panasonic AG-UX90 manuals
Add to My Manuals
Save this manual to your list of manuals |
Panasonic AG-UX90 manual content summary:
- Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 1
Operating Instructions Memory Card Camera-Recorder Model No. AG-UX90 Please read these instructions carefully before using this product, and save this manual for future use. P PJ F1016YA0 ENGLISH DVQP1146ZA - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 2
. ≥ Use only the recommended accessories. ≥ Do not remove covers. ≥ Do not repair this unit by yourself. Refer servicing to qualified service personnel. of naked flames, such as lighted candles, on this unit. (For the U.S.A. and Canada only) AC adaptor This AC adaptor operates on AC between 100 V - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 3
on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 4
of Conformity Model Number: AG-UX90P, AG-UX90PJ Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America Two Riverfront Plaza Newark NJ07102 Support contact: 1-800-524-1448 This device complies with Part 15 of the FCC Rules. Operation is subject to the following - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 5
Concerning the battery Battery pack (Lithium ion battery pack) ≥ Use the specified unit to recharge the battery pack. ≥ Do not use the battery pack with . ∫ Product identification marking Product Memory Card Camera-Recorder Battery charger AC adaptor Bottom Bottom Bottom Location Conforms to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 6
with care. Cleaning ≥ Before cleaning, detach the battery or pull the AC cable from the AC outlet, Use of benzine, paint thinner, alcohol, or dishwashing liquid may alter the camera body or peel the surface finish. Do not use these solvents. ≥ When using a chemical dust cloth, follow the instructions - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 7
result in an explosion. If the operating time is very short even after the battery has been recharged, the battery has worn out. Please purchase a new battery. About the AC adaptor/battery charger ≥ If the temperature of the battery is extremely high or extremely low, charging may take time or the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 8
a radio, radio reception may be disturbed. Keep the AC adaptor or battery charger 1 m (3.3 feet) or more away from the radio. ≥ When using the AC adaptor or battery charger, it may generate whirring sounds. However, this is normal. ≥ After use, be sure to disconnect the AC cable from the AC outlet - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 9
Panasonic if above operations support 4K. 4K , remove the battery and/or the use with this unit SDHC Memory Card and SDXC Memory Card ≥ 4 GB or more Memory Cards that do not have the SDHC logo or 48 GB or more Memory Cards that do not have the SDXC logo are not based on SD Memory Card Specifications - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 10
operating instructions ≥ The battery pack is referred to as the "Battery". ≥ SDHC Memory Card and SDXC Memory Card are referred to as the "SD card". ≥ Function that can be used for Recording Mode: Function that can be used ≥ These operating instructions are designed for use with models AG-UX90P/PJ. - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 11
media 43 Recording motion picture 43 Switching between Auto and Manual Mode 45 Adjusting the Picture Quality 47 Using the zoom 49 Image Stabilizer Function 51 Focus 53 One Push AF 56 Push AF 57 Focus Assist 57 White Balance 61 Iris/Gain adjustment 65 Iris adjustment 65 Deleting scenes - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 12
139 Troubleshooting 193 About recovery 197 Updating the firmware incorporated into the unit 197 About copyright 198 Recording functions that cannot be used simultaneously 200 Recording modes/approximate recordable time 201 Approximate number of recordable pictures 202 Specification 203 - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 13
Accessories Check the accessories before using this unit. Keep the accessories out of reach of children to prevent swallowing. Battery pack*1 Eye cup (l 22) Battery charger AC adaptor AC cable Microphone holder (l 23) Microphone holder mounting screws (l 23) 12 mm length (0.47 q) (2 screws) - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 14
Some optional accessories may not be available in some countries. Product numbers correct as of September 2016. These may be subject to change. Unidirectional microphone (AG-MC200G) Battery pack (VW-VBD58/AG-VBR59/AG-VBR89/AG-VBR118) Battery charger (AG-B23/AG-BRD50) LED video light (VW-LED1) - 14 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 15
to the SD card It is possible to record motion pictures and still pictures to the SD card using a variety of recording functions. ≥ This unit supports relay/simultaneous recording using double card slots. Linking to external devices USB Device Mode Transfer data (files) to perform nonlinear editing - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 16
wireless module that support this unit (l 132) to the USB HOST terminal of this unit allows you to connect to a wireless LAN network. You can perform the following operations by connecting this unit and an iPad on which the AG ROP application is installed: ≥ Checking the camera status ≥ Checking the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 17
≥ Do not use any other AC adaptors except the supplied one. 14 Camera remote terminal [ CAM REMOTE] (l 117) ≥ FOCUS IRIS terminal (3.5 mm (0.14 q) diameter mini jack) ≥ ZOOM S/S terminal (2.5 mm (0.1 q) diameter super mini jack) 15 Headphone terminal [ ] (l 104, 117) 16 VIDEO - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 18
with 1/4-20UNC and 3/8-16UNC screws. Use the size that matches the diameter ND filter switch [ND FILTER] (l 100) 27 Focus auto/Manual/¶ switch [FOCUS A/M/¶] (l 53) 28 Iris button [IRIS] (l 33, 80) 40 Gain button [GAIN] (l 67) 41 White Balance button [WHITE BAL] (l 61) 42 Jog dial [SEL/PUSH SET] (l 61 - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 19
) 59 Recording lamp (Rear) (l 175) 60 Shoulder strap fixture 61 Eye cup mount (l 22) 62 Viewfinder (l 37) 63 Eye cup (l 22) 64 Battery release button [PUSH] (l 26) 65 Battery holder (l 26) 66 Built-in microphone 67 Recording lamp (Front) (l 175) 68 Lens cover (l 21) 69 Lens (LEICA DICOMAR) 70 User - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 20
71 72 73 74 75 76 77 78 79 80 81 71 Accessory shoe 72 Sub zoom lever (l 49, 159) ≥ This lever functions in the same manner as the zoom lever. ≥ The zoom speed is controlled with this lever in a way different from the way it is controlled with the zoom lever. (l 50) 73 Zoom lever [T/W] (In Recording - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 21
/closing the lens cover You can open/close the lens cover by sliding the lens cover open/close lever. ≥ When this unit is not in use, close the lens cover to protect the lens. OPEN CLOSE ≥ Do not press the lens cover hard. This may damage the lens or the lens - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 22
∫ Adjust the length of the hand strap so that it fits your hand. Adjust the hand strap according to the size of your hand. ≥ If you find it difficult to fasten the buckle B, move the pad A forward, and fasten the buckle B again. 1 Open the buckle. 2 Pull the end of the belt. ∫ Attaching the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 23
mm (0.83 q) external microphone (AG-MC200G: optional) can be attached. Check in advance whether the microphone you wish to use can be attached. 1 Attach the AUDIO INPUT1 terminal (XLR 3 pin). ≥ When wiring the microphone cable, use the cable clamper of this unit. ≥ Keep the microphone holder screw - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 24
with this unit (as of September 2016) The battery that can be used with this unit is VW-VBD58/AG-VBR59/AG-VBR89/AG-VBR118. ≥ The AG-VBR59/AG-VBR89/AG-VBR118 supports quick charging. It has been found that counterfeit battery packs which look very similar to the genuine product are made available to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 25
the battery charger. ≥ Slide the battery horizontally into the battery charger along the " " mark. ≥ The corresponding CHARGE indicator lights and charging starts. ≥ The CHARGE indicator turns off when charging is complete. Slide the battery to remove it. ≥ We recommend using Panasonic batteries - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 26
inserting it in the direction shown in the figure. ≥ Insert the battery until it clicks and locks. Removing the battery Make sure that the power switch is set to OFF and the status indicator is turned off, and then remove by holding onto it taking - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 27
. Charging time and recordable time vary depending on the usage conditions such as high/ low temperature. ≥ The batteries heat up after use or charging. This is not a malfunction. ≥ The optional battery charger AG-B23 (DE-A88) can be used to charge the battery but charging will take longer. - 27 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 28
battery AG-VBR59. ∫ Checking the remaining power using this unit Battery capacity indication ≥ The display changes as the battery capacity reduces. If the battery the indicator is an approximate guide. When the battery pack is connected to the video camera or the charger, refer to the remaining - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 29
live" as long as the AC adaptor is connected to an electrical outlet. Important: ≥ Use the supplied AC adaptor. Do not use the AC adaptor of another device. ≥ Do not use they will go. ≥ Even when you use the AC adaptor for recording images, keep the battery connected. This allows you to continue the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 30
this unit ≥ The cards that you can use are correct as of September 2016. ≥ We recommend that you use a Panasonic Memory Card. Card type Capacity SDHC Memory Card 4 GB to 32 GB SDXC Memory Card 48 GB to 128 GB ≥ We do not guarantee the operation of SD cards other than the ones above - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 31
lamp has gone off. Access lamp A ≥ When this unit is accessing the SD card, the access lamp lights up. 1 Open the SD card slot cover and insert (remove) the SD card into (from) the them to their cases when you are not using them. ≥ About disposing of or giving away the SD card. (l 8) - 31 - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 32
To turn off the unit Set the power switch to OFF while pressing the lock release button. The status indicator goes off. A The status indicator lights on. ≥ To turn on the unit again after the [ECONOMY (BATT)] or [ECONOMY (AC)] is activated, set the power switch to OFF once, and then - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 33
Preparation Using the LCD monitor/Viewfinder The viewfinder is turned off and the LCD monitor is turned on when the LCD monitor is extracted. The viewfinder is - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 34
Using the LCD monitor 1 Extract the LCD monitor in the direction as indicated in the figure. ≥ Hold the LCD monitor extract part A, and extract the LCD - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 35
How to use the touch screen You can operate by directly touching the LCD monitor (touch screen) with your finger. ∫ Touch Touch and release the touch screen to select icon or picture. ≥ Touch the center of the icon. ≥ Touching the touch screen will not operate while you are touching another part of - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 36
outdoors. Select the menu. (l 41) MENU : [DISP SETUP] # [POWER LCD] # [+1] (Makes brighter)/[0] (Normal)/[-1] (Makes less bright) ≥ When the AC adaptor is in use, [POWER LCD] is set to [+1] automatically. ≥ [0] is selected when: j [USB MODE SELECT] is set to [DEVICE] and this unit is connected to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 37
the viewfinder. 2 Adjust the focus by operating the eyepiece corrector lever. A Eyepiece corrector lever [EVF SETTING] It adjusts brightness and color density of the viewfinder. ≥ Use the jog dial to change the settings When [COLOR] is set to s16, images are displayed in black and white. - 37 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 38
. Select the menu. (l 41) MENU : [DISP SETUP] # [EVF COLOR]# [ON] or [OFF] [ON]: [OFF]: Displayed in color Displayed in black and white ≥ If you adjust the [COLOR] setting in [EVF SETTING], [EVF COLOR] will be set to [ON]. Recording yourself ≥ Change the mode to Recording Mode. (l 32) - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 39
], and follow the instructions from Step 2-3 of be set, then set the desired value using / . ≥ The year can be battery. ≥ If the time display becomes [- -], the built-in lithium battery needs to be charged. To recharge the built-in lithium battery, connect the AC adaptor or attach a charged battery - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 40
∫ Time zone table Time difference Region 0:00 London, Casablanca s1:00 Azores s2:00 Fernando de Noronha s3:00 Rio de Janeiro, Sao Paulo, Buenos Aires s3:30 Newfoundland s4:00 s4:30 s5:00 s6:00 s7:00 Manaus, La Paz Caracas Toronto, New York, Miami, Lima Chicago, Houston, Mexico City Denver, - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 41
Preparation Using the menu screen ≥ You can also select menu items by operating the jog dial. (l 102) MENU 1 MENU Press the MENU button . 2 Touch the top menu A. 3 Touch the submenu B. ≥ Next (Previous) page can be displayed by touching / . 4 - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 42
is backlit, it will become dark in the recording. ≥ Keep your arms near your body and separate your legs for better balance. ≥ For stable images, it is recommended to use a tripod whenever possible. Recording Selecting a media to record You can specify the card slot to which motion pictures are to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 43
formatted, then all the data recorded on the medium will be erased and cannot be restored. Back up important data on a PC etc. (l 122) ≥ When using two SD cards, format both SD cards. 1 Select the menu. MENU : [OTHER FUNCTION] # [FORMAT MEDIA] 2 Touch [SD CARD 1] or [SD CARD 2]. ≥ When formatting is - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 44
00 R 1h20m MAIN R 1h20m 50M 59.94p TC 00:00:00.00 / (White) Counter display (l 76) Card slot number R 1h20m MAIN Approximate remaining recordable time continues.) AVCHD scene MOV/MP4 scene (when using an SDHC Memory Card) MOV/MP4 scene (when using an SDXC Memory Card) Approximately 4 GB - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 45
Auto Mode. Activates Auto Shutter as a manual mode. Press the SHUTTER button to switch between Auto Shutter Mode and Manual Shutter Mode. Activates Auto Tracking White Balance in Auto Mode. Activates Auto Tracking White Balance as a manual mode. The white balance is adjusted according to the setting - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 46
the FOCUS A/M/¶ switch. Automatic Tracking White Balance The Auto Tracking White (ATW) Balance function of this unit automatically adjusts the White Balance according to the lighting condition. If Auto Tracking White Balance does not work correctly, switch to Manual Mode first, and then adjust the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 47
image may become rough due to emphasized noise and edges. To avoid such problems, it is necessary not to add this effect on parts where emphasizing is Menu item [SKIN TONE DTL] (l 142) RB gain control function When the White Balance mode is set to [Ach] or [Bch], this function enhances or reduces - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 48
scene to be recorded. (l 145) Sets the gamma curve for dark areas.(l 145) Knee function This function sets the compression of video signals to prevent white saturation in images. ∫ Menu item [KNEE MODE]: [KNEE MASTER POINT]: [KNEE MASTER SLOPE]: Sets the compression level of highly bright image - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 49
Recording Using the zoom The unit can deliver a maximum optical zoom of 15k. ≥ (When the Close-up recording (zoom in) ≥ If you take your finger off the zoom lever during zoom operation, the operation sound may be recorded. When returning the zoom lever to the original position, move it quietly. ≥ - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 50
Variable Frame Rate Mode (l 92) j When [REC FORMAT] is set to a setting with a size of UHD (3840k2160) j During Freeze Frame (l 87) Using Fast Zoom When [FAST ZOOM] is set to [ON], you can use Fast Zoom while operating the zoom with the zoom lever. 1 Select the menu. MENU : [SW SETUP] # [FAST ZOOM - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 51
Optical Image Stabilizer is set to (setting canceled) j When the size is set to UHD (3840k2160) in [REC FORMAT] (l 148) j In Variable Frame Rate Mode (l 92 Stabilization may not be possible under strong shaking conditions. ≥ When using a tripod, we recommend that you set the Image Stabilizer to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 52
corrected in a balanced manner. Although larger values allow you to correct significant camera shake more camera shake that falls in the high frequency range while weakening the correction performance against slow camera shake that falls in the low frequency range. We recommend that you use - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 53
use Manual Focus. FOCUS A M ʿ A FOCUS A/M/¶ switch B PUSH AUTO button C Focus ring PUSH AUTO ≥ Switch to Manual Mode. (l 45) 1 Set the FOCUS A/M/¶ switch to [M] to enable Manual non-displayed focus value. ≥ When you perform a zoom operation in the macro range, this unit may go out of - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 54
focus value according to the rotational position of the focus ring. Since the operation of the focus ring results in a greater change in focus value, this # [EVF/LCD PEAK FREQ.] # [HIGH] or [LOW] ≥ [EVF/LCD DETAIL] is canceled in following cases: j If you use Focus Assist (peaking) (l 57) - 54 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 55
targeted subject even when an intervening object passes in front of the camera or the subject disappears from the view of this unit. We recommend complete the setting. ≥ This function is not available in the following cases: j In manual focus mode (l 53) j In Variable Frame Rate Mode (l 92) ≥ When a - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 56
(l 97) ≥ This function is not available in the following cases: j In manual focus mode (l 53) j When using Area Mode (l 88) j During Freeze Frame (l 87) One Push AF If you press the PUSH AUTO button in Manual Focus Mode, the camera performs high-speed focusing until the image is focused. ≥ Switch to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 57
Manual Focus. (l 53) Press and hold the PUSH AUTO button. ≥ The focus position will be automatically adjusted for the subject at the center of the screen. ≥ If you set [AREA MODE] to [FOCUS], [FOCUS/IRIS] or [FOCUS/Y GET] and use will be maintained. ≥ You can also use Push AF with the USER button to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 58
[FOCUS ASSIST 1] or [FOCUS ASSIST 2] is registered. ≥ You can also use Focus Assist by touching the USER button icon to which [FOCUS ASSIST 1] or [FOCUS ASSIST 2] is registered. ≥ To turn off Focus Assist, perform the following operations: j Press the FOCUS ASSIST button or the USER button again, or - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 59
COLOR] # desired color [Red]/[Blue]/[Yellow]/[White] (When setting the peaking strength) 1 If you turn the unit off j (If you operate the FOCUS ASSIST button or the USER button to which use Focus Assist. (l 87) ≥ Peaking may not be displayed when you use Digital Zoom (l 85). To zoom in and use - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 60
Focus Assist: j During motion picture recording or PRE-REC (l 92, 165) j When using Digital Zoom j When using Area Mode (l 88) j During auto recording (l 96) j In Variable Frame Rate Mode (l 92) j During AG ROP application connection (l 131) ≥ If you set the magnification level of the magnified - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 61
the White Balance manually. 5600K Ach ヴユヵ WHITE BAL A White Balance B Color temperature display ≥ Displayed when the White Balance mode is set to Ach or Bch. ≥ The color temperature display is not guaranteed to indicate an exact value. Use the indicated value only as a guide - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 62
you press the WHITE BAL button to switch to [Bch]. (l 64) *1 This setting is selected automatically when one of the following operations is performed: j the USER button to which [ATW] is registered or press the WHITE BAL button, the White Balance mode cannot be changed: j In Auto Mode with [ATW] - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 63
can set ATW Lock by registering [ATW LOCK] to a USER button. ≥ Please refer to page 80 for details about setting the USER button. 1 Set the White Balance mode to [ATW]. 2 Press the USER button to which [ATW LOCK] is registered or touch the applicable USER button icon. ≥ To cancel ATW Lock, press - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 64
, an error message "WB SET NG" or "BB SET NG" is displayed on the screen. In such case, use other mode. ≥ It is not possible to operate Auto White Balance or Auto Black Balance without registering [AWB] to a USER button. ≥ The contents previously set are maintained in the [Ach] or [Bch]. Perform - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 65
value B Auto iris icon* * It is displayed in Auto Iris Mode. IRIS 1 IRIS button 2 Iris ring ≥ Switch to Manual Mode. (l 45) 1 Press the IRIS button to switch to Manual Iris Mode. ≥ disappears. 2 Adjust the iris by rotating the iris ring. Iris value: CLOSE !# (F11 to F3.0) !# OPEN ≥ Value - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 66
[EXIT] to complete the setting. ≥ You can also change the [A.IRIS LEVEL] setting with a USER button. (l 95) Utilizing the USER button It is convenient to use following functions of the USER button when it is set to Iris adjustment. ≥ Please refer to page 80 for details about setting the USER button - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 67
≥ Use the jog dial to change the settings. 0dB GAIN 1 Jog dial 2 GAIN button A Gain value ≥ In Auto Gain Mode, "AGC" is displayed; in Manual Gain Mode, the gain value is displayed in dB. B [GAIN] ≥ Switch to Manual Mode. (l 45) 1 Press the GAIN button to switch to [LOW GAIN - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 68
] settings, which differ in size (picture size): (l 148) j [REC FORMAT] settings with a size indicated as UHD (3840k2160) j [REC FORMAT] settings with a picture size of 1920k1080 or below Super Gain You can use Super Gain by registering [SUPER GAIN] to a USER button. Super Gain allows you to set the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 69
follows: j [SYSTEM MODE] # [LOW LIGHT MODE] (l 151) ≥ This function is not available in the following cases: j In manual mode j During Freeze Frame (l 87) j When this unit is connected to the AG ROP application (l 135) ≥ This mode is canceled if one of the following operations is performed: j If you - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 70
when recording fast-moving subjects. ≥ Use the jog dial to change the settings. A.SHTR 1/60 A Shutter speed B Auto Shutter display ≥ This is displayed in Auto Shutter Mode. C [SHUTTER] SHUTTER ヴユヵ 1 SHUTTER button 2 Jog dial ≥ Switch to Manual Mode. (l 45) 1 Press the SHUTTER - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 71
∫ Shutter speed guide for fast moving subjects not look smooth. ≥ If you record an extremely bright object or record under indoor lighting, color and screen brightness may change or a horizontal line may appear on the screen. , set the iris, focus, and White Balance mode to manual settings. - 71 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 72
LINE MIC ʴ7 CH1 SELECT INT(L) INPUT1 INPUT2 CH2 SELECT INT(R) INPUT1 INPUT2 A INPUT1 switch B INPUT2 switch C CH1 SELECT switch D CH2 SELECT switch ∫ Using the built-in microphone Audio is recorded with the built-in microphone (2 ch) when the CH1 SELECT switch is set to INT(L) and - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 73
LINE LEVEL] or [INPUT2 LINE LEVEL] setting. (l 167) *2 The input level varies depending on the [INPUT1 MIC LEVEL] or [INPUT2 MIC LEVEL] setting. (l 167) 3 Use the CH1 SELECT switch to select the input signal to be recorded to audio channel 1. INT(L): Audio from the built-in microphone L (left) ch is - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 74
unit is turned off when a problem occurs with the +48 V power supply. ≥ The battery will discharge faster if you use a phantom microphone. ≥ If there level automatically. [MANUAL]: Adjusts the level manually. 2 (If you have set to [MANUAL]) Adjust the input level operating the AUDIO LEVEL CH1 - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 75
Using the ALC function ALC can reduce audio noise. For audio channel 1, select [AUDIO ALC CH1]: for audio channel 2, select [AUDIO ALC CH2]. 1 Set [AUDIO LEVEL CH1]/[AUDIO LEVEL CH2] to [MANUAL]. (l 74) 2 Select the menu. MENU : [AUDIO SETUP] # [AUDIO ALC CH1] or [AUDIO ALC CH2] # desired setting [ - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 76
Recording Counter display You can change a counter display that indicates how much time has elapsed during recording or playback. COUNTER A COUNTER button B RESET button RESET Press the COUNTER button to switch the counter display. ≥ The display will be switched in the following order: Time - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 77
desired setting [DF]: [NDF]: Time code is compensated in accordance with the actual time. It is mainly used for broadcasting such as TV programs. It will not compensate the time code. (There will be a reset when the built-in lithium battery is exhausted when it is set to [FREE RUN]. - 77 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 78
Information. ≥ Set [REC MODE] to [AVCHD]. (l 148) 1 Select the menu. MENU : [RECORD SETUP] # [UB PRESET] 2 Touch the item to set and change with / . ≥ You can use numbers from 0 to 9 and letters from A to F. ≥ It will be set to 00 00 00 00 when the RESET button is pressed. 3 Touch [EXIT] to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 79
Setting the Recording Counter Recording Counter will display the recording time in seconds. 0:00:00 (hour : minute : second (When [REC COUNTER] is set to [TOTAL])) SCN 0:00:00 (hour : minute : second (When [REC COUNTER] is set to [SCENE])) [REC COUNTER] Select the counting method during the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 80
the default settings. USER1 button USER2 button USER3 button USER4 button USER5 button USER6 button USER7 button [AREA] [FOCUS MACRO] [SLOT SEL] [LOW LIGHT] [ZEBRA] [O.I.S.] [LCD/EVF OUTPUT] USER8 button USER9 button USER10 button USER11 button USER12 button USER13 button [REC CHECK] [AWB] [FRZ - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 81
operation icons are displayed. (When you use the USER1 to USER7 button) O.I.S. LCD/EVF (When you use the USER8 button) 6 7 USER 1 2 REC CHECK 8 3 ZEBRA 4 5 (When you use the USER9 button) (When you use j Push Auto (l 56, 57) j Auto White Balance (l 61, 64) ∫ Switch display/not-display - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 82
Focus Assist 1 Backlight Compensation Spotlight Black Fade White Fade Auto Tracking White Balance ATW Lock Digital Zoom Focus Assist 2 Recording Check Last Scene Delete DRS Freeze Frame Super Gain*1 Area Mode Histogram Push Auto EVF/LCD detail Low Light mode Level Gauge Focus Macro Flash band - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 83
Mode*2 Function Auto White Balance Slot Selection [AF AREA] [LCD/EVF OUTPUT] [LOW GAIN] [MID GAIN] [HIGH GAIN] [MENU] [AF Area] [LCD/EVF] [LowGain] [MidGain] [HighGain] [MENU] AF Area Width adjustment LCD/EVF Output Low gain Mid gain High gain Menu *2 Not available during AG ROP application - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 84
button. (l 80) Fade in/fade out effect (black) can be added to the video and audio that is being recorded. Press USER button or touch USER button icon in using fade in become black. White Fade ≥ Register "White Fade" to a USER button. (l 80) Fade in/fade out effect (white) can be added to the video - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 85
Lock ≥ Register "ATW Lock" to a USER button. (l 80) This sets the White Balance mode to [ATW LOCK].(l 63) Digital Zoom ≥ Register "Digital Zoom" to a zoom magnification each time you press the applicable USER button. ≥ When using Digital Zoom, the larger you set the zoom magnification, the lower the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 86
of the video recorded last can be played back. It will return to recording screen once the playback is completed. ≥ Playback operation is not (l 148) j Set [2 SLOTS FUNC.] to [SIMULTANEOUS]. (l 162) j PRE-REC is used (l 92, 165) j During the Interval Recording (l 163) j During Freeze Frame (l 87) - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 87
range by compressing the video signal level of the camera operations will be disabled. j Recording motion pictures j Canceling Freeze Frame j Operating the FOCUS A/M/¶ switch ≥ This function is not available in the following cases: j When using Manual Mode. (l 45) This changes the gain value to a [SUPER - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 88
the subject you touch and displays the luminance level of the subject. ∫ Using Area Mode ≥ Register "Area Mode" to a USER button. (l frame (With a USER button icon) 1 Touch and hold the recording screen to display operation icons. 2 Touch the USER button icon. To change the size of the area frame - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 89
cases: j In Variable Frame Rate Mode (l 92) j During AG ROP application connection (l 131) ≥ Area mode is canceled in following 80) You can use the USER button as the PUSH AUTO button. ≥ Pressing the USER button or touching the USER button icon in Manual Focus Mode allows you to use One Push AF. - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 90
mode" to a USER button. (l 80) ≥ Slide the AUTO/MANU switch to switch to Auto Mode. Switch to Low Light mode, which is suited to recording under low light. (l 69) Level Gauge ≥ Register "Level Gauge" to a USER button. (l 80) This function displays the horizontal/vertical tilt of the unit with the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 91
of the image when recording is performed in an environment where another camera is firing its flash. ≥ FBC appears on the screen. A or 23.98p (l 148) j When using [DIGITAL ZOOM] (l 85) j During Freeze Frame (l 87) j In Variable Frame Rate Mode (l 92) j In Low Light mode (l 69) ≥ The setting will - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 92
3 seconds before the operation, while MOV/MP4 will be recorded from approximately 4 seconds before the operation. ≥ [P-] is displayed 1/2 can be gained. Quick motion (undercrank recording) A fast motion effect is used in scenes showing the flow of clouds, people standing in the middle of crowds, - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 93
1 Press USER button or touch USER button icon in the recording screen. ≥ [VFR] will be displayed. ≥ The frame rate display will change. (Example) 12 : 23.98p A Frame Rate (fps) B Frame rate in [REC FORMAT] ≥ ALC / A.REC will be displayed. Audio is not recorded during recording. 2 Rotate - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 94
using Variable Frame Rate (VFR) Mode with a low frame rate setting, this unit may not be able to keep up with changes in the image. In such a case, set the iris, focus and White Balance mode to manual to a USER button. (l 80) You can use Fast Zoom when operating the zoom with the zoom lever. (l 50) - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 95
as 99% when it is over 99%. ≥ This function is not available during Freeze Frame. (l 87) ≥ You can record an image with little white saturation if you manually adjust the shutter speed or brightness not to display zebra pattern. (l 65, 70) ≥ The zebra pattern does not appear on the images actually - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 96
Scene File ≥ Register "Scene File" to a USER button. (l 80) You can save the scene file settings to the SD card or load them from the SD card to this unit. ∫ Saving scene file settings 1 Press USER button or touch USER button icon in the recording screen. 2 Touch [SAVE]. 3 Touch the name of the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 97
USB port is in use, a message may be displayed, instructing you to unmount the USB cable safely. Select [YES] to terminate the connection safely. Auto White Balance ≥ Register "Auto White Balance" to a USER button. (l 80) You can change the White Balance mode or use Auto White Balance or Auto Black - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 98
Output" to a USER button. (l 80) This changes how to turn on/off the LCD monitor and Viewfinder. (l 33) Low gain ≥ Register "Low gain" to a USER button. (l 80) The gain value can be changed to low gain. (l 67) ≥ This item cannot be set during Freeze Frame. (l 87) Mid gain ≥ Register "Mid gain" to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 99
Recording Useful functions ャモンヴ A BARS button B ND FILTER switch C DISP/MODE CHK button Color Bar color bars are displayed depending on the [BARS TYPE] setting. (l 158) ≥ The test tone volume differs depending on the [TEST TONE] setting. (l 169) ≥ You can record color bars as motion pictures. ≥ - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 100
can switch the built-in optical ND filter setting. (The filter adjusts the amount of light.) ≥ Use this function when recording a bright subject outdoors under a clear sky that causes the screen to look white. Slide the ND filter switch. ND1/16 ND1/64 A ND filter setting B Recommended ND filter - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 101
White Balance modes [Ach] and [Bch] ([AWB A]/[AWB B]). Mode information display4: Displays the settings for [REMOTE REC], [REMOTE REC LINK], [HDMI TC OUTPUT], [CAMERA NUMBER], [SUB REC BUTTON] and [SUB ZOOM]. Mode information display5: Displays the settings for [AUDIO LOW CUT CH1], [AUDIO LOW - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 102
items You can select and set menu items (l 41), etc. using the jog dial. 1 Rotate the jog dial on the menu screen, etc., to move the cursor. ≥ The selected item will be displayed in yellow. 2 Push the jog dial to set. Menu operations for setting a value When a menu that lets you set - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 103
Using the multi manual function You can select the following functions and adjust their settings using the jog dial. You ) Allows you to display/select operation icons on the recording screen. Settings Adjusts the gain value. Adjusts the VAR setting of the White Balance. Adjusts the size of the AF - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 104
Manual Mode. (l 45) VAR adjustment Press the WHITE BAL button and the USER button to which [AWB] is registered to set the White Balance function is displayed in white. (Function Execution Mode) If you have selected [ ICONS], you can rotate the jog dial to select an operation icon. 2 Push the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 105
picture/Still picture playback 1 Set this unit to playback mode. (l 32) 2 Touch the play mode select icon A. UHD UHD UHD UHD UHD UHD UHD UHD UHD Media display The selected media is displayed in yellow. 3 Select the media C you wish to play back. ヮヱフ 4 (To - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 106
button to which [SLOT SEL] is registered. (l 80) UHD UHD UHD UHD UHD UHD UHD UHD UHD 6 Select the playback operation by touching the operation icon. TC 00:02:30.00 G Operation icon ≥ If you touch the screen while an operation icon is being displayed or do not touch - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 107
are displayed when playing back motion pictures, and recording date and file number when playing back still pictures. ∫ Speaker/Headphone volume adjustment Operate the volume lever, sub zoom lever or jog dial to adjust the speaker/headphone volume during Motion Picture Playback Mode. Adjusting the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 108
, or when video recorded using this device is played back in another device, playback may not proceed normally, or may not be possible. (Please check compatibility in the instruction manual of your device.) ≥ Motion pictures recorded with devices other than this unit are not supported by this unit - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 109
Motion picture playback using operation icon For details on the basic playback operations, refer to page 105. Playback operation Skip playback (to the start of a scene) Playback display During Playback Operating steps Touch the LCD monitor and slide from right to left (from left to right) during - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 110
recorded. Recording format [REC FORMAT] setting with a size of UHD (3840k2160) [REC FORMAT] setting with a size of FHD ( recording still pictures 8.3M R3000 / (White) 8.3M R3000 (Red) Card slot 9999 or less. ≥ The 16:9 still pictures recorded using this unit may be cropped at the edges when - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 111
played back. ≥ Repeat Playback cannot be used for the slide show playback of the still VIDEO SETUP] # [RESUME PLAY] # [ON] If playback of a motion picture is stopped, scene. appears on the thumbnail view of the stopped ≥ The memorized resume position is canceled if one of the following operations - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 112
or still pictures recorded on the same day can be played back in succession. 1 Touch the date select icon. UHD UHD UHD UHD UHD UHD UHD UHD UHD A Date select icon 2 Touch the playback date. ≥ The scenes or still pictures recorded on the date selected are displayed - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 113
or still pictures to delete. (l 105) 1 Select the menu. MENU : [VIDEO SETUP] or [PICT. SETUP] # [DELETE] # desired setting [ALL SCENES]: picture is selected and the Touch the scene/still picture again to cancel the operation. ≥ Up to 99 scenes can be selected to be deleted. indication appears - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 114
THUMBNAIL button to switch this unit to the Playback Mode. (l 32) 1 Select the menu. MENU : [VIDEO SETUP] or [PICT. SETUP] # [SCENE PROTECT] 2 Touch the scene/still picture to be protected. the scene/still picture again to cancel the operation. ≥ Touch [Return] to complete the settings. - 114 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 115
SD Card may not be used. Copying 1 Press the THUMBNAIL button to switch this unit to the Playback Mode. ≥ Use a sufficiently charged battery or the AC adaptor. 2 the thumbnail. Touch the scene/still picture again to cancel the operation. ≥ (When [SELECT DATE] is selected) When touched, the date - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 116
If you will delete the motion pictures or still pictures after copying is complete, be sure to play back the motion pictures or still pictures to check that they have been copied to correctly before deleting. ≥ Depending on the following conditions, the time it takes for copying may be longer. j The - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 117
iris with the iris ring of this unit. ≥ If you switch to Auto Mode when [A.IRIS] is set to [ON], the remote control cannot be used. - 117 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 118
and play back scenes recorded with their size set to UHD (3840k2160) in [REC FORMAT], you can enjoy finely-detailed 4K motion pictures. For an external monitor that does not support 4K motion picture, you can change the [RESOLUTION] setting so that 4K motion pictures can be played back at a lower - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 119
the following cases: j When [REC FORMAT] is set to a setting with a size of UHD (3840k2160) j When [REC FORMAT] is set to [SA 480/59.94i] Example of the screen (operation icon and Counter display etc.) can be displayed/not displayed on the external monitor. MENU : [DISP SETUP] # [VIDEO OUT OSD] - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 120
Please read the operating instructions for the external device.) ≥ [DOWN CONV.] outputs images in standard picture quality. ∫ To use an AV [RESOLUTION] # [DOWN CONV.] ≥ In the following cases, the video and audio are not output from VIDEO OUT terminal and AUDIO OUT terminal: j When an HDMI cable is - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 121
REC FORMAT] [RESOLUTION] setting [SYSTEM] UHD (3840k2160)/ 29.97p [1080p] [1080i] [DOWN CONV.] [SYSTEM] UHD (3840k2160)/ 23.98p [1080p] [ picture) [1080p] [1080i] [DOWN CONV.] External output resolution HDMI OUT terminal VIDEO OUT terminal 2160/29.97p 1080/59.94p 1080/59.94i 480/59.94p - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 122
using a USB 3.0 Cable (commerciallyavailable), image data in the SD card can be transferred. ≥ This unit supports USB 3.0. ≥ Concerning non-linear editing, refer to the instruction manual of your editing software. ≥ It is impossible to write data to the SD card on this unit from a PC. Operating - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 123
≥ Use the AC adaptor to free you from worrying about the battery running USB Cable. ≥ When using the battery, the LCD monitor Use a commercially-available double-shielded USB 3.0 cable with a ferrite core. If possible, we recommend using using an SDXC Memory Card, some PC may not recognize the data - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 124
the unit is operated while connected to a PC, disconnect the battery and/or AC adaptor, wait approximately 1 minute, reconnect the battery and/or AC adaptor and sound data, but also various important information, and it is associated using a folder structure which is like a figure. If even part of - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 125
16 is set in [CAMERA NUMBER SET]. ≥ Do not delete the SD card's folders on a PC. Doing so may make the SD card unusable in this unit. ≥ When data not supported by this unit has been recorded on a PC, it will not be recognized by this unit. ≥ Always use this unit to format - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 126
maintaining the image quality. ≥ Please read the operating instructions of the external media device for how to use it. Preparing for copying/playing back Refer to the following support site for information about an external media device. http://pro-av.panasonic.net/ (This Site is English only) When - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 127
Connect the AC adaptor to this unit. ≥ Use the AC adaptor to free you from worrying about the battery running down. 3 Turn on this unit, and Connect the external media device to the USB HOST terminal of this unit. ≥ If you use a USB HDD, connect to the USB HDD with the USB Cable supplied with the USB - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 128
and the external media device to format. You may no longer be able to use the external media device if you format them on another device such as a PC formats the external media device in exFAT. ∫ Displaying media information The used space of the external media device can be checked. ≥ Connect this - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 129
SD cards, refer to page 115. 4 Touch the desired items following the instructions on the screen. ≥ It will return to the previous step by touching [Return on the thumbnail. Touch the scene/still picture again to cancel the operation. ≥ (When [SELECT DATE] is selected) When touched, the date is - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 130
118) 2 Touch [Playback from External Media]. 3 Touch the scene or still picture to be played back and then play it back. ≥ The playback operation is performed the same as when playing back motion pictures or still pictures. (l 105, 109) To terminate the connection between this unit and the external - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 131
is installed. USB HOST A Wireless module that support this unit B Direct connection C Wireless access point connection D iPad and AG ROP application You can perform the following remote control operations with the AG ROP application: ≥ Checking the camera status ≥ Checking the thumbnails of the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 132
the AG ROP application: iOS 7.1 or later (as of September 2016) Wireless module Attach a wireless module that support this unit to the USB HOST terminal of this unit. ≥ For details on wireless modules that support this unit, refer to the support desk at the following website. http://pro-av.panasonic - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 133
enter characters with a keyboard. Icon [A-a] [Return] [] Description of operation Switches between uppercase and lowercase. Returns to the previous screen. The entered the set user account name and password to [AG ROP] in [Settings] on the iPad. For details, refer to [CONNECTION] in Help of the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 134
with [WIRELESS SETUP] set to [SSID(SELECT)] or [SSID(MANUAL)]. [SERVER]: Enables the DHCP server function when connecting with [WIRELESS correct. ≥ When not using the gateway, set it to [0.0.0.0]. ≥ When [DHCP] is set to [OFF] or [CLIENT], apply the [IP Address] setting to [AG ROP] in [Settings] - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 135
[CONNECTION] in Help of the AG ROP app. ∫ Icons to the iPad. ≥ Attach a wireless module that support this unit to the USB HOST terminal of this used. [2.4GHz]/[5GHz] [CHANNEL (2.4GHz)]: Sets the channel to be used for 2.4 GHz. [AUTO]/[CH1]/[CH6]/[CH11] [CHANNEL (5GHz)]: Sets the channel to be used - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 136
access point Configure the settings in this section to connect this unit and an iPad using a wireless access point. ∫ Searching for wireless access points to set up a connection ≥ Attach a wireless module that support this unit to the USB HOST terminal of this unit. (l 132) ≥ Set [USB MODE SELECT - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 137
for use. ≥ When [DHCP] in [Wireless LAN setup] is set to [OFF] or [CLIENT], apply the [IP Address] setting to [AG ROP] in [Settings] (l 134) on the iPad. For details, refer to [CONNECTION] in Help of the AG ROP app. ∫ Setting up a connection manually ≥ Attach a wireless module that support this - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 138
you to easily connect with the same settings as used previously. ≥ Attach a wireless module that support this unit to the USB HOST terminal of this unit connection, after terminating the AG ROP application connection, set [USB MODE] to [OFF]. ≥ Up to 20 most recently used connections can be stored - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 139
(USER button) (l 83) j Area Mode (l 88) j Low Light mode (l 90) ≥ Settings that are changed remotely with the AG ROP application are applied to the corresponding settings of this unit. ≥ When WARNING is flashing on the AG ROP application screen, remote control operations may not be performed due to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 140
for recording with modulation in resolution, color shade, and contrast Setting which allows you to use a scene file with a picture tone similar to that produced with a digital still camera. Setting appropriate for recording as a cinema with high contrast Setting appropriate for recording as a cinema - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 141
switch the scene number by touching F1: to F6: while displaying the operation icons. (l 101) ≥ You can rename the titles for scene numbers renamed to the one that has been entered.) 3 Touch [Enter]. ≥ The title will be updated. [LOAD/SAVE] You can save the scene file settings to the SD card or load - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 142
[SKIN TONE DTL] This makes skin colors appear softer for a more attractive appearance. This is more effective if you record a person closely from the torso up. [ON]/[OFF] 1 Touch [SKIN TONE DTL]. 2 Touch [ON]. 3 Touch [EXIT] to exit the menu screen. ≥ If the background or anything else in the scene - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 143
[ON] or [OFF]. [ON]: Maintains the [R GAIN] and [B GAIN] settings when Auto White Balance/Auto Black Balance is used. [OFF]: Resets the [R GAIN] and [B GAIN] settings when Auto White Balance/Auto Black Balance is used. ≥ To make additional changes, repeat Steps 2s3. 4 Touch [EXIT] to exit the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 144
setting that is assigned to [F1:] in [FILE SELECT] is "0". [CHROMA PHASE] Adjusts color balance. 1 Touch [CHROMA PHASE]. 2 Touch / to adjust settings. ≥ You can select a in a picture tone similar to that produced with a digital still camera. 3 Touch [EXIT] to exit the menu screen. [MASTER PED - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 145
setting item. [HD]: This is the video gamma feature for HD (High Definition). [SD]: This increases gain in darker areas more than [HD] does. [ ]: Expresses colors in a picture tone similar to that produced with a digital still camera. 3 Touch [EXIT] to exit the menu screen. ≥ When [CINE-LIKE - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 146
, select the compression level of the high intensity video signals received through the image sensor. 1 Touch [KNEE MODE]. 2 Touch / to select the setting item. [AUTO]: Sets the level automatically according to the signals received. [MANUAL]: Applies the [KNEE MASTER POINT] and [KNEE MASTER - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 147
[DRS EFFECT] Selects the level of the DRS function. 1 Touch [DRS EFFECT]. 2 Touch / to select the setting item. [1]/[2]/[3] ≥ Higher the value, greater the compression level of the highly illuminated area. ≥ Higher the value, greater the noise of the dark area. 3 Touch [EXIT] to exit the menu screen - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 148
. Interlace (interlacing scanning) Video signal that divides the effective with highest quality image in this unit when set to [UHD 2160/29.97p 100M]. ≥ Depending on the [REC MODE setting, its required Speed Class of the SD card differs. Use an SD card that meets the settings. For details, refer to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 149
FHD 1080/23.98p 50M] [FHD 1080/59.94i 50M] Size (Picture size) UHD (3840k2160) FHD (1920k1080) Frame rate 29.97p 23.98p 59.94p 29.97p Mbps Average 17 Mbps Average 5 Mbps Average 8 Mbps Average 9 Mbps ≥ Recordable time using the battery (l 27) ≥ The default setting for [REC MODE] is [MP4], and the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 150
Recording format [UHD 2160/29.97p 100M] [UHD 2160/23.98p 100M] [FHD 1080/59.94p 50M] [FHD 1080/29.97p 50M] [FHD 1080/23.98p 50M] [FHD 1080/59.94i 50M] [PS - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 151
[LOW LIGHT MODE] Enables/disables Low Light mode. (l 69) ≥ Slide the AUTO/MANU switch to switch environment where another camera is firing its flash. (l 91) [ON]/[OFF] [CAMERA NUMBER SET] This sets the camera number for this unit. 1 Touch [CAMERA NUMBER SET]. 2 Touch / to change the Camera Number. ≥ - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 152
, refer to page 82. ≥ The default settings are as follows: j USER1: [AREA] j USER2: [FOCUS MACRO] j USER3: [SLOT SEL] j USER4: [LOW LIGHT] j USER5: [ZEBRA] j USER6: [O.I.S.] j USER7: [LCD/EVF OUTPUT] j USER8: [REC CHECK] j USER9: [AWB] [USER10]/[USER11]/[USER12]/[USER13] Register functions to - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 153
a negative gain value (a value between -3 dB and -1 dB) is selected, if you set [EXTENDED SENSITIVITY] to [OFF] and operate the GAIN button, the gain value will be set to 0 dB. However, the [LOW GAIN] setting will be maintained. [MID GAIN] Sets the gain value for the [MID GAIN] position of the GAIN - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 154
's default setting is "12 dB". ≥ When a negative gain value (a value between -3 dB and -1 dB) is selected, if you set [EXTENDED SENSITIVITY] to [OFF] and operate the GAIN button, the gain value will be set to 0 dB. However, the [HIGH GAIN] setting will be maintained. [SUPER GAIN] Sets the gain value - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 155
can assign ATW. [OFF]: Does not assign ATW when the WHITE BAL button is pressed. [Ach]: Sets the White Balance mode to ATW when the WHITE BAL button is pressed to switch to [Ach]. [Bch]: Sets the White Balance mode to ATW when the WHITE BAL button is pressed to switch to [Bch]. [PRST]: Sets - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 156
[WB PRESET] Sets which White Balance mode to use when the WHITE BAL button is pressed to switch to the PRST position. [3200K]/[5600K]/[VAR] [WB VAR] Sets the color temperature when the White Balance mode is set to [VAR]. (l 64) 1 Touch [WB VAR]. 2 Touch / to adjust settings. ≥ You can select a value - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 157
[FOCUS RING DRIVE] This sets the way you adjust focus with the focus ring. (l 54) [SPEED]/[COARSE]/[FINE] [FOCUS MACRO] This enables/disables the Focus Macro function. [ON]/[OFF] ≥ If [ON] is selected, subjects at a distance of approximately 10 cm (3.93 q) to infinity can be brought into focus when - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 158
] Enable/disable of the sub recording start/stop button on the handle can be switched. [INHIBIT]/[ACTIVE] [FAST ZOOM] When [ON] is selected, you can use Fast Zoom when operating the zoom with the zoom lever. (l 50) [ON]/[OFF] - 158 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 159
focus ring with this unit and operating them with the AG ROP application during AG ROP application connection. (l 139) [IP REMOTE]/[CAMERA] ≥ Selecting [IP REMOTE] enables you to operate this unit with the AG ROP application, while selecting [CAMERA] enables you to operate this unit directly. - 159 - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 160
]/[15 dB]/[18 dB]/[21 dB]/[24 dB]/[27 dB]/[30 dB] ≥ The default setting is determined as follows: j When a setting with a size indicated as UHD (3840k2160) is set for [REC FORMAT]: [24 dB] j When a setting with a picture size of 1920k1080 or below is set for [REC FORMAT]: [30 dB] [AUTO - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 161
.94i/29.97p 1/30 or more 23.98p 1/24 or more ≥ This function is not available in the following cases: j During Freeze Frame (l 87) j In Low Light mode. (l 69) ≥ When the shutter speed becomes 1/30 or 1/24, the screen may be seen as if frames are missed and after images may appear - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 162
(l 92) j During the Interval Recording (l 163) *2 This item is not available when different types of SD cards (SDHC Memory Card/SDXC Memory Card) are used. ∫ Relay recording This is simple Relay Recording. It is possible to continuously record on the SD card in the other card slot even when the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 163
card that ran out of space when the SD card currently being used as a destination still has sufficient remaining recordable time. ≥ The maximum To set [REC FORMAT] ≥ Following recording formats enable Interval Recording. Recording format [UHD 2160/29.97p 100M], [FHD 1080/29.97p 50M], [HA 1080/59. - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 164
2 second. ≥ Color balance and focus may not be adjusted automatically depending on light sources or scenes. If so, manually adjust these settings. (l the frame rate before recording. [ON]/[OFF] ≥ For information on how to use Variable Frame Rate Mode, refer to page 92. [FRAME RATE] You can adjust - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 165
approximately 3 seconds before the operation, while MOV/MP4 will be recorded from approximately 4 seconds before the operation. (l 92) [ON During Freeze Frame (l 87) j In Variable Frame Rate Mode (l 92) ≥ Even when [VIDEO OUT OSD] is set to [OFF], the date and time of recording are displayed on the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 166
CH2] Reduces the level of low-pitched sound for audio channel 2. [ON]/[OFF] ≥ You may not see the full effect depending on the recording conditions. [AUDIO LEVEL CH1] Switches the adjustment method of the audio recording level for audio channel 1. (l 74) [AUTO]/[MANUAL] [AUDIO LEVEL CH2] Switches - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 167
with natural sound when set to [OFF]. (l 75) ≥ Set [AUDIO LEVEL CH1] to [MANUAL]. (l 74) [ON]/[OFF] [AUDIO ALC CH2] If you set this item to [ON], with natural sound when set to [OFF]. (l 75) ≥ Set [AUDIO LEVEL CH2] to [MANUAL]. (l 74) [ON]/[OFF] [INPUT1 LINE LEVEL] Sets the input level of the audio - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 168
an external device using the recording start/stop button. [OFF]: Controls recording performed with an external device using the USER button time code information when this unit is connected to another device (HDMI-SDI converter, etc.) with an HDMI cable. ≥ When performing remote recording with - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 169
Recording Mode with the jog dial. (l 104) [ON]/[OFF] [TEST TONE] Selects the test tone output when color bars are displayed. (l 99) [OFF]: [LEVEL 1]: [LEVEL 2]: Does not output a test tone. Outputs a high volume test tone. Outputs a low volume test tone. [LCD/EVF OUTPUT] This sets how to turn - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 170
Display setting Different menu items are displayed depending on whether this unit is in Recording Mode or Playback Mode. All default settings are indicated with underlined text. MENU : [DISP SETUP] # desired setting [ZEBRA DETECT 1] Selects the brightness level of the left-leaning zebra patterns on - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 171
[GUIDE LINES] You can check if the image is level while recording motion pictures and still pictures. The function can also be used to estimate the balance of the composition. / / /[OFF] ≥ The guidelines do not appear on the images actually recorded. ≥ The setting changes as follows when using - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 172
value between 0 and 99 is displayed. [mm] All values are displayed in millimeter. [OFF] No value is displayed. [VIDEO OUT OSD] The information displayed on the screen (operation icon and counter display etc.) can be displayed/ not displayed on the external monitor. (l 119) [ON]/[OFF] [DATE/TIME - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 173
, ND filter, Focus Display, White Balance, Iris, Gain, Auto Iris, Shutter Speed) [ON]/[OFF] [CARD & BATTERY] Display can be switched between [USER BUTTON DISPLAY], [GUIDE LINES], [SAFETY ZONE], [CENTER MARKER], [DATE/TIME], [AUDIO LEVEL METER], [LENS STATUS] and [CARD & BATTERY]. [ON]/[OFF] [POWER - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 174
] [EVF COLOR] The recording images or playback images on the viewfinder can be selected between color/black and white. (l 38) [ON]/[OFF] [EVF/LCD DETAIL] Setting this item to [ON] helps you achieve focus /LCD PEAK FREQ.] Sets the peaking frequency for [EVF/LCD DETAIL]. (l 54) [HIGH]/[LOW] - 174 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 175
PC etc. (l 123) [MEDIA STATUS] The used space and remaining recordable time of the SD card The capacities of this unit, PCs and software are expressed as 1 GB=1,024k1,024k1,024 LAMP] The recording lamp lights up during recording. When this is set to [OFF], it does not light during recording. [FRONT - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 176
(BATT)] When about 5 minutes have passed without any operation, this unit automatically turns off to save battery life. [ON]/[OFF] ≥ This unit will not automatically turn off even if the [ECONOMY (BATT)] is set to [ON] in following cases: j PRE-REC is used (l 92, 165) j When [USB MODE SELECT] is - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 177
[LICENSE.TXT]. ≥ When using the battery, the LCD monitor turns off after about 5 seconds. Touch the screen to turn the LCD monitor on. [LANGUAGE] You can select the language on the screen display and the menu screen. AG-UX90P [English]/[Français]/[Español]/[Português] AG-UX90PJ [English]/[Français - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 178
for the AG ROP application. (l 132) [SET]/[OFF] [WIRELESS SETUP] Set the wireless LAN connection method. (l 135) [DIRECT]/[SSID(SELECT)]/[SSID(MANUAL)] [Wireless are displayed. You can easily connect with the same settings as used previously by selecting a connection record from History. (l 138) [ - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 179
to the default settings, allowing you to use it again. Maintenance MENU : [MAINTENANCE] # desired setting [VERSION] The version of the firmware of this unit is displayed. [UPDATE] The firmware of this unit is updated. (l 197) [HOUR METER] This displays the operation time of this unit, how many times - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 180
to switch this unit to the Playback Mode. ≥ Touch the play mode select icon, and set this unit to Motion Picture Playback Mode. (l 105) MENU : [VIDEO SETUP] # desired setting [REPEAT PLAY] Playback of the first scene starts after playback of the last scene finishes when set to [ON]. (l 111) [ON - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 181
Picture Setup ≥ Press the THUMBNAIL button to switch this unit to the Playback Mode. ≥ Touch the play mode select icon, and set this unit to Still Picture Playback Mode. (l 105) MENU : [PICT. SETUP] # desired setting [SCENE PROTECT] Still pictures can be protected so that they are not deleted by - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 182
(l 96) Auto Mode (l 45) Remaining battery power (l 28) , (White) Recording to card possible (motion picture) , Low Light mode (l 151) DRS (l 87, 146) Area Mode (l 88) AF Area Width adjustment (l 56, 97) Freeze Frame (l 87) Image Stabilizer (l 51) Wireless LAN connection status (l 135) AG - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 183
Color temperature display (l 61) ATW, LOCK, P3200K, P5600K, VAR, Ach, Bch White Balance (l 61) VFR Variable Frame Rate mode (l 92, 164) ND 1/4, ND Center Marker (l 171) AGC, 0 dB Gain value (l 67) SHUTTER Multi Manual Function (l 103) A.SHTR Auto Shutter display (l 70) 1/100 Shutter speed - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 184
00.00/TC 00:00:00:00 Counter Display (l 76) , (White) Card slot number No.0010 Scene Number 100-0001 Still picture folder/ In 9-scene display in thumbnail mode) (l 105) UHD , FHD , PH , PS , HA , HE indications -- (Time display) The built-in battery is low. (l 39) Warning for recording of - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 185
SD card is not supported by this ≥ Check the SD card. unit. THIS CARD CANNOT RECORD IN VIDEO MODE. This is displayed when the SD card ≥ Use an SD card with while recording is in progress. It is also displayed when the lens of the camera does not move. ≥ Check the SD card. ≥ Turn off and on this - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 186
DATA. This is displayed when the ≥ Check the SD card. management information cannot be recovered. CANNOT USE SD CARD IN VIDEO MODE, CONTROL DATA ERROR. ≥ The operation will stop. ≥ Use another SD card to perform recording. CONTROL DATA ERROR HAS BEEN DETECTED. (SD CARD) Defective management - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 187
possible due to, ≥ Check the SD card. for example, a problem with the SD card. Cannot delete data on card. The SD card version. CANNOT RESET NUMBER. The SD card cannot be used with this unit. ≥ Insert a recordable SD card. THUMBNAIL supported. Behavior and cause ≥ Check the SD card. ≥ Check to see - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 188
used. Disconnect the USB cable from this unit. This is displayed when the memory capacity of the external media is 32 GB or below or above 2 TB. ≥ Connect a supported example, a problem with the copy destination media device. ≥ Check the copy destination media device. Use destination media - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 189
recordings from other devices. This is displayed when a copy-related operation involving a scene recorded with another device is performed. ≥ Copy only the maximum limit set by applicable standards is reached, for example. ≥ Use an SD card with enough recordable space. COULD NOT COPY SOME SCENES - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 190
It flashes once per second. On-screen display The message [LOW BATTERY.] is displayed. AG ROP application screen [ WARNING ] lights up. Meaning of the warning The battery is depleted. Recording/playback The operation stops. This unit turns off automatically. Solution Charge or replace - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 191
error has occurred during recording or playback. Recording/playback The operation stops. Solution Replace the SD card. Status indicator s On-screen display The message [CHANGE THE BATTERY.] is displayed and flashes red. AG ROP application screen [ WARNING ] flashes once per second. Meaning - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 192
The card is nearly full Status indicator s On-screen display The remaining recordable time flashes red. (When it is less than 1 minute) AG ROP application screen [ WARNING ] flashes once per second. (When it is less than 1 minute) Meaning of the warning The SD card is almost out of - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 193
the image very fast, but this is because the unit is using MOS for the image sensor. This is not a malfunction. Problem This unit cannot be turned on. This unit does not stay on long enough. Battery runs down quickly. This unit cannot be operated though it is turned on. This unit does not - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 194
BATTERY] or [OTHER DISPLAY] of the [DISP SETUP] is [OFF]. (l 173) ≥ Press the COUNTER button to switch the counter display. (l 76) Problem bring into focus in Auto Focus Mode, use the Manual Focus Mode to adjust the focus. (l recorded under fluorescent light, mercury light or sodium light, etc., but - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 195
device or edited with editing software j Scenes with damaged data up important data on a PC etc. Problem Although this unit is correctly connected to an operating instructions of the device for details. ≥ When connected to other devices using only the battery, reconnect using the AC adaptor. - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 196
operating environment. (l 122) ≥ Connect the USB Cable again after restarting the PC and turning on this unit again. ≥ To disconnect the USB Cable safely, double-click the icon in the task tray and follow the instructions on the screen. Problem . Depending on the device used, the images may stop - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 197
when the scenes are displayed in thumbnail. ≥ Use a sufficiently charged battery or the AC adaptor. ≥ Depending on the Update completes by loading the downloaded files to the camera via the SD card. For details on update, visit the support desk at the following website: http://pro-av.panasonic - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 198
are trademarks of Panasonic Corporation and Sony of Leica Camera AG. ≥ and other countries. ≥ App Store is a service mark of Apple Inc. ≥ "Wi-Fi®" mentioned in these instructions are usually the video provider licensed to provide AVC Video. No license is granted or shall be implied for any other use - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 199
terms and conditions thereof, which can be accessed by selecting [SOFTWARE INFO] in "Other Functions" as described in "Using the Menu" in the Operating Instructions (PDF file). At least three (3) years from delivery of this product, Panasonic will give to any third party who contacts us at the - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 200
Others Recording functions that cannot be used simultaneously Due to the specifications of this unit, depending on the recording function being used, it is not possible to use or select certain other recording functions. ≥ "±": Available; "s": Not available* * "Not available" includes instances - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 201
min" for minute and "s" for second. ≥ If recording for long periods, prepare batteries for 3 or 4 times the period you wish to record for. (l 27) [REC MODE] is set to [MOV] or [MP4] Recording format 4 GB [UHD 2160/29.97p 100M] s [UHD 2160/23.98p 100M] [FHD 1080/59.94p 50M] [FHD 1080/29.97p 50M - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 202
indicated on the label of an SD card is the total of the capacity for copyright protection and management and the capacity which can be used on the unit, a PC etc. - 202 - - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 203
Specification Memory Card Camera-Recorder General Power: DC 7.28 V (When using battery) DC 12 V (When using AC adaptor) Power consumption: 12.2 W (When using LCD monitor) indicates safety information Ambient operating temperature: 0 oC to 40 oC (32 °F to 104 °F) Ambient operating 32 q] UHD (3840k2160 - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 204
1.3 lx (F2.8, Super Gain 36 dB, Manual slow shutter 1/30 sec.) Digital zoom: 2k/ 128 GB); UHS-I supported Refer to page 30 [MOV], [MP4] [UHD 2160/29.97p 100M]/ [UHD 2160/23.98p 100M]/ rule for Camera File video Video signal for external output: 8 bit 4:2:2 Recording video signal: 8 bit 4:2:0 Video - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 205
HOST terminal: Type A connector, 9-pin In Recording mode; USB 2.0 compatible (5 V, 0.5 A) In Playback mode; USB 3.0 compatible (5 V, 0.9 A), used for external media device connection*, bus power supported * External media device with a capacity of 32 GB or below or a capacity above 2 TB cannot be - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 206
k1-7/16 qk2-1/4 q] (Excluding the DC cord portion) Battery charger Input voltage: DC 12 V, 3.0 A Output voltage: DC 8.4 V, 4.0 A indicates safety information Charging current: Max. 4000 mA Ambient operating temperature: 0 oC to 40 oC (32 °F to 104 °F) Ambient operating humidity: 10%RH to 80%RH (no - Panasonic AG-UX90 | AG-UX90 Operating Instructions - Page 207
Panasonic Corporation Web site: http://www.panasonic.com © Panasonic Corporation 2016
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
 |
 |
Operating Instructions
Memory Card Camera-Recorder
Model No.
AG-UX90
Please read these instructions carefully before using this product, and save this manual for future
use.
DVQP1146ZA
ENGLISH
F1016YA0
P
PJ