Panasonic PT-EZ570U Operating Instructions - Page 24

Using Remote control, Installing and Removing batteries, Setting Remote control ID numbers

Get Panasonic PT-EZ570U PDF manuals and user guides View all Panasonic PT-EZ570U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Using Remote control Installing and Removing batteries 1111 Open the cover 2222 Install batteries and close the cover (Insert the - side first.) Preparation zzRemove the batteries in the reverse order of installation. Setting Remote control ID numbers When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single remote control, if unique ID number is assigned to each projector. After setting the ID number of the projector, set the same ID number to the remote control. There are 65 different ID codes (All, Code 1~Code 64), the initial ID number is [All]. JJ Setting the ID number 1) W hile holding down the button, enter a 1-digit or 2-digit number corresponding to the desired ID code number by using the number buttons 0 to 9. 2) The ID code is changed when the button is released. 3) The examples are as follows: C ode 1= + or + + , Code 2= + or + + , Code 16= + + , Code 64= + + JJ Resetting the ID number 1) T he ID code is reset to [All] (default) by pressing the button and button at the same time for 5 seconds or more. Attention zz The remote control transmission is disabled during the ID code change procedure. zz The status of the ID code is not stored after replacing batteries. Note zzFor details, please refer to the [Remote control] of the [Setting] menu. (Æpage 67) MENU button Number buttons 24 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
24
- ENGLISH
Preparation
Using Remote control
Installing and Removing batteries
Open the cover
1 )
Install batteries and close the cover
2 )
(Insert the – side first.)
Remove the batteries in the reverse order of
z
installation.
Setting Remote control
ID numbers
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each
projector individually using single remote control, if unique ID number is assigned to each projector.
After setting the ID number of the projector, set the same ID number to the remote control.
There are 65 different ID codes (All, Code 1~Code 64), the initial ID number is [All].
J
Setting the ID number
1)
While holding down the <MENU> button, enter a 1-digit or 2-digit number
corresponding to the desired ID code number by using the number buttons 0 to 9.
2)
The ID code is changed when the <MENU> button is released.
3)
The examples are as follows
:
Code 1= <MENU>+<1> or <MENU>+ <0> + <1> ,
Code 2= <MENU>+<2> or <MENU>+ <0> + <2>,
Code 16= <MENU>+ <1> + <6>, Code 64= <MENU>+ <6> + <4>
J
Resetting the ID number
1)
The ID code is reset to [All] (default) by pressing the <MENU> button and <0> button
at the same time for 5 seconds or more.
Attention
The remote control transmission is disabled during
z
the ID code change procedure.
The status of the ID code is not stored after replacing batteries
z
.
Note
For details, please refer to the [Remote control] of the
z
[Setting] menu. (
Æ
page 67)
MENU button
Number buttons