Pioneer SC-85 Owner's Manual - Page 35

Hdmi Out 2, Out 2, Out 1+2, Hdmi Out 3, Out 3, Main/hdzone, Zone Setup, Hdmi Out, Hdmi Setup, 4k/60p

Get Pioneer SC-85 PDF manuals and user guides View all Pioneer SC-85 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

03 Connecting your equipment ! When connecting to an HDMI/DVI-compatible monitor using the HDMI OUT 2 terminal, switch the HDMI output setting to OUT 2 or OUT 1+2. See Switching the HDMI output on page 85 . In the same way, when an HDMI/DVI-compatible monitor is connected to the HDMI OUT 3 terminal, switch the HDMI OUT 3 setting to ON (page 85 ). In this case, MAIN/HDZONE at ZONE Setup must be set to MAIN (page 110 ). ! For input components, connections other than HDMI connections are also possible (see Connecting your DVD player with no HDMI output on page 35 ). ! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables. - When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT terminal, so there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on page 76 ). After setting the ARC, some time may be required for the connected device to be recognized and the sound to be produced. - If you use a coaxial digital audio cable or RCA (analog) audio cable, you'll need to tell the receiver which digital or analog audio input you connected the TV to (see The Input Setup menu on page 52 ). - Please refer to the TV's operation manual for directions on connections and setup for the TV. ! If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in accordance with TV performance. When the 4K/60p setting is changed to 4:4:4, the video image may not be output normally unless the HDMI cable supports 4K/60p 4:4:4 24 bit (18 Gbps transmission). In such a case, select 4:2:0 (page 85 ). ! You cannot input 4K/60p 4:4:4 24 bit video from HDMI IN 3 to the IN 7 terminal. Use the BD IN, HDMI IN 1 or HDMI IN 2 terminal. ! The HDMI OUT 3 terminal outputs 4K/60p 4:4:4 24 bit video when MAIN/HDZONE is set to MAIN. When it is set to HDZONE, the 4K/60p 4:4:4 24 bit video is not output. Connecting your DVD player with no HDMI output This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no HDMI output) to the receiver. HDMI/DVI-compatible monitor DVD player, etc. HDMI IN Select one Select one VIDEO OUT COMPONENT VIDEO OUT AUDIO OUT DIGITAL OUT VIDEO Y PB PR R ANALOG L COAXIAL OPTICAL HDMI ASSIGNABLE 1 -7 Y IN 1 (DVD) IN 2 (DVR/ BDR) ASSIGNABLE MONITOR OUT OUT 1 (CONTROL) OUT 2 OUT 3 (HDZONE) PB PR SELECTABLE IN 1 (DVD) BD IN DVR/BDR OUT IN COMPONENT VIDEO IN 2 IN 3 IN 4 (SAT/CBL) (DVR/BDR) LAN (10/100) IN 6 IN 7 MHL (OUTPUT 5 V 0.9 A MAX) COAXIAL ASSIGNABLE OPTICAL ASSIGNABLE IN 1 IN 2 IN 1 IN 2 (DVD) (SAT/CBL) (TV) (DVR/BDR) DC OUTPUT for WIRELESS LAN (OUTPUT 5 V 0.6 A MAX) OUT HDMI ASSIGNABLE 1 -7 Y IN 1 (DVD) IN 2 (DVR/ BDR) ASSIGNABLE MONITOR OUT OUT 1 (CONTROL) OUT 2 OUT 3 (HDZONE) PB PR SELECTABLE IN 1 (DVD) BD IN DVR/BDR OUT IN IN 2 (SAT/CBL) IN 3 IN 4 (DVR/BDR) LAN (10/100) IN 6 IN 7 MHL (OUTPUT 5 V 0.9 A MAX) COAXIAL ASSIGNABLE OPTICAL ASSIGNABLE IN 1 IN 2 IN 1 IN 2 (DVD) (SAT/CBL) (TV) (DVR/BDR) DC OUTPUT for WIRELESS LAN (OUTPUT 5 V 0.6 A MAX) OUT COMPONENT VIDEO ! With factory default settings, video from the video cable or component cable will not be output from the HDMI terminal. To output video, you must switch video input to the device connected with the video cable or component cable and set V.CONV to ON (page 82 ). ! If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables (page 34 ). - When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio Return Channel) function, the sound of the TV can be input to the receiver via the HDMI OUT 1 terminal, so there is no need to connect an audio cable. In this case, set ARC at HDMI Setup to ON (see HDMI Setup on page 76 ). ! If you use an optical digital audio cable or RCA (analog) audio cable, you'll need to tell the receiver which digital input you connected the player to (see The Input Setup menu on page 52 ). ! If HDZONE is set to on, video images connected using a video cable or component cable are not output from the HDMI terminal. To output video images, turn HDZONE off (page 86 ). 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
35
Connecting your equipment
03
!
When connecting to an HDMI/DVI-compatible monitor using the
HDMI OUT 2
terminal, switch the HDMI
output setting to
OUT 2
or
OUT 1+2
. See
Switching the HDMI output
on
page 85
.
In the same way, when an HDMI/DVI-compatible monitor is connected to the
HDMI OUT 3
terminal, switch
the
HDMI
OUT 3
setting to
ON
(
page 85
). In this case,
MAIN/HDZONE
at
ZONE Setup
must be set to
MAIN
(
page 110
).
!
For input components, connections other than HDMI connections are also possible (see
Connecting your DVD
player with no HDMI output
on
page 35
).
!
If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables.
—
When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the
HDMI OUT
terminal, so
there is no need to connect an audio cable. In this case, set
ARC
at
HDMI Setup
to
ON
(see
HDMI Setup
on
page 76
).
After setting the
ARC
, some time may be required for the connected device to be recognized and the sound to
be produced.
—
If you use a coaxial digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digi-
tal or analog audio input you connected the TV to (see
The Input Setup menu
on
page 52
).
—
Please refer to the TV’s operation manual for directions on connections and setup for the TV.
!
If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in
accordance with TV performance. When the
4K/60p
setting is changed to
4:4:4
, the video image may not be
output normally unless the HDMI cable supports 4K/60p 4:4:4 24 bit (18 Gbps transmission). In such a case,
select
4:2:0
(
page 85
).
!
You cannot input 4K/60p 4:4:4 24 bit video from
HDMI
IN 3
to the
IN 7
terminal. Use the
BD IN
,
HDMI
IN 1
or
HDMI
IN 2
terminal.
!
The
HDMI OUT 3
terminal outputs 4K/60p 4:4:4 24 bit video when
MAIN/HDZONE
is set to
MAIN
. When it is
set to
HDZONE
, the 4K/60p 4:4:4 24 bit video is not output.
Connecting your DVD player with no HDMI output
This diagram shows connections of a TV (with HDMI input) and DVD player (or other playback component with no
HDMI output) to the receiver.
LAN
OPTICAL
COAXIAL
COMPONENT
VIDEO
HDMI
ASSIGNABLE
DVR/BDR
IN
OUT
MONITOR
OUT
P
B
Y
P
R
IN
1
(DVD)
IN
2
(DVR/
BDR)
LAN
(10/100)
OUT 3
(HDZONE)
OUT 2
OUT 1
(CONTROL)
DC OUTPUT
for WIRELESS LAN
(OUTPUT 5 V
0.6 A MAX)
(OUTPUT 5 V
0.9 A MAX)
OPTICAL
COAXIAL
SELECTABLE
ASSIGNABLE
ASSIGNABLE
IN
1
(DVD)
BD IN
IN
2
(SAT/CBL)
IN
3
(DVR/BDR)
IN
6
IN
4
IN
7
MHL
IN
1
(TV)
IN
2
(DVR/BDR)
IN
1
(DVD)
IN
2
(SAT/CBL)
OUT
COMPONENT
VIDEO
HDMI
ASSIGNABLE
1
-
7
HDMI IN
DIGITAL OUT
COAXIAL
OPTICAL
ANALOG
R
L
AUDIO OUT
VIDEO
VIDEO OUT
Y
P
B
P
R
COMPONENT VIDEO OUT
HDMI/DVI-compatible monitor
DVD player, etc.
Select one
Select one
!
With factory default settings, video from the video cable or component cable will not be output from the HDMI
terminal. To output video, you must switch video input to the device connected with the video cable or compo-
nent cable and set
V.CONV
to
ON
(
page 82
).
!
If you want to listen to the sound of the TV over the receiver, connect the receiver and TV with audio cables
(
page 34
).
—
When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI ARC (Audio
Return Channel) function, the sound of the TV can be input to the receiver via the
HDMI OUT 1
terminal, so
there is no need to connect an audio cable. In this case, set
ARC
at
HDMI Setup
to
ON
(see
HDMI Setup
on
page 76
).
!
If you use an optical digital audio cable or RCA (analog) audio cable, you’ll need to tell the receiver which digi-
tal input you connected the player to (see
The Input Setup menu
on
page 52
).
!
If HDZONE is set to on, video images connected using a video cable or component cable are not output from
the HDMI terminal. To output video images, turn HDZONE off (
page 86
).