Pioneer SC-85 Owner's Manual - Page 62

05 Basic playback Pairing the Bluetooth ADAPTER and Bluetooth wireless technology device "Pairing" must be done before you start playback of Bluetooth wireless technology content using the Bluetooth ADAPTER. Make sure to perform pairing the first time you operate the system or any time pairing data is cleared. The pairing step is necessary to register the Bluetooth wireless technology device to enable Bluetooth communications. For more details, see also the operating instructions of your Bluetooth wireless technology device. ! Pairing is required when you first use the Bluetooth wireless technology device and Bluetooth ADAPTER. ! To enable Bluetooth communication, pairing should be done with both your system and Bluetooth wireless technology device. ! If the Bluetooth wireless technology device's security code is "0000", there is no need to make the security code setting on the receiver. Press BT ADPT to set the ADAPTER PORT input, then conduct the pairing operation on the Bluetooth wireless technology device. If pairing is successful, there is no need to performing the pairing operation below. ! When using the AS-BT200 only: This unit complies with Bluetooth Specifications Ver. 2.1. When this unit and another device equipped with Bluetooth wireless technology both comply with Bluetooth Specification Ver. 2.1, pairing of the two may be possible without the need for inputting a password. In this case, a passcode may be displayed on this receiver and on the device equipped with Bluetooth wireless technology. If this happens, check that the same passcode is displayed on this receiver and the device equipped with Bluetooth wireless technology, then press ENTER. After this, also perform the connection operation on the Bluetooth device to be connected. If the passcode does not match the code displayed on the Bluetooth device to be connected, press RETURN to cancel pairing, then try starting over. Press BT ADPT to set the ADAPTER PORT input, then conduct the pairing operation on the Bluetooth wireless technology device. If pairing is successful, there is no need to performing the pairing operation below. ! Pair one unit at a time. ! When connecting this receiver by Bluetooth connections with a device equipped with the Bluetooth function to listen to music, do not connect any devices other than this receiver by Bluetooth connection to the Bluetoothequipped device. If a Bluetooth connection is already established with a device other than this receiver, disconnect the other device before connecting this receiver. 1 Press BT ADPT on the remote control to switch the receiver to ADAPTER PORT input. 2 Press TOP MENU to select Bluetooth Setup. 3 Use i/j to select 'PIN' then press ENTER. 4 Use i/j to select one of PIN codes 0000, 1234 or 8888, then press ENTER. You can use any of 0000, 1234 or 8888 PIN codes. Bluetooth wireless technology device using any other PIN code cannot be used with this receiver. 5 Press the RETURN button twice to exit Bluetooth Setup. 6 Switch on the Bluetooth wireless technology device that you want to make pair, place it near the receiver and set it to the pairing mode. 7 From the Bluetooth wireless technology device list, select Bluetooth ADAPTER and enter the PIN code selected in step 4. 8 Check to see that the Bluetooth ADAPTER is detected by the Bluetooth wireless technology device. If the receiver and Bluetooth wireless technology device are not paired, start over from step 6. Listening to music contents of a Bluetooth wireless technology device with your system 1 Press BT ADPT on the remote control to switch the receiver to ADAPTER PORT input. 2 From the Bluetooth wireless technology device, perform the operation to connect to the Bluetooth ADAPTER. ! When the Bluetooth ADAPTER is not plugged into the ADAPTER PORT, No Adapter will be displayed if ADAPTER PORT input is selected. 3 Start playback of music contents stored on the Bluetooth wireless technology device. This receiver's remote control buttons can be used for basic playback of files stored on Bluetooth wireless technology devices. ! Bluetooth wireless technology device should be compatible with AVRCP profile. ! Depending on the Bluetooth wireless technology device you use, operation may differ from what is shown in the remote control buttons. 4 While listening to a source, set the remote control to the receiver operation mode, then press ADV repeatedly to select SOUND RETRIEVER AIR. Notes ! The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PIONEER CORPORATION is under license. Other trademarks and trade names are those of their respective owners. ! With this receiver, when an iPod is connected or disconnected while the music of a Bluetooth wireless technology device is playing, the connection with the Bluetooth wireless technology device may be canceled. ! The SOUND RETRIEVER AIR listening mode can only be selected when the ADAPTER PORT input. Notes ! The PIN code may in some cases be referred to as PASSKEY. ! For information on enabling pairing on the Bluetooth wireless technology device, connection procedures, etc., see the Bluetooth wireless technology device's operating instructions. 62