Pioneer SC-85 Owner's Manual - Page 85
Press CH LV..
View all Pioneer SC-85 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 85 highlights
09 Using other functions Notes ! When 7.2ch + Speaker B or 5.2ch + SP-B Bi-Amp is selected for the Speaker System setting (page 104 ) and Speaker B Link (HDMI Setup on page 76 ) is set to "ON", the setting of the speaker terminals that are played changes automatically when HDMI OUT 1 and HDMI OUT 2 are switched. For details, see Switching the HDMI output on page 85. ! The subwoofer output depends on the settings you made in Manual speaker setup on page 104 . However, if SP: B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed). ! All speaker systems (except 7.2ch + Speaker B connections) are switched off when headphones are connected. Switching the HDMI output Set which terminal to use when outputting video and audio signals from the HDMI output terminals. The HDMI OUT 1 terminal is compatible with the Control with HDMI function. 1 Press OUT P.. 2 Use i/j to select 'OUT 1/2'. 3 Use k/l to select the output settings for the HDMI OUT 1 and HDMI OUT 2 terminals. Please wait a while when Please wait ... is displayed. The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed. ! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro- nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV's remote control. 4 Use i/j to select 'OUT 3'. 5 Use k/l to select the output settings for the HDMI OUT 3 terminal. Please wait a while when Please wait ... is displayed. The setting switches between ON and OFF each time this is pressed. ! When MAIN/HDZONE is set to HDZONE, the output of the HDMI OUT 3 terminal cannot be switched (page 110 ). 6 When you're finished, press RETURN. About the Speaker B Link function When 7.2ch + Speaker B or 5.2ch + SP-B Bi-Amp is selected for the Speaker System setting (page 104 ) and Speaker B Link (HDMI Setup on page 76) is set to "ON", the setting of the speaker terminals that are played changes automatically when HDMI OUT 1 and HDMI OUT 2 are switched. The setting switches as follows. ! OUT 1+2 - Switches to SP: A+B ON. Sound is output simultaneously in the room where the A speakers are located and in the room where the B speakers are located. ! OUT 1 - Switches to SP: A ON. Sound is only output in the room where the A speakers are located. ! OUT 2 - Switches to SP: B ON. Sound is only output in the room where the B speakers are located. HDMI 4K/60p signal output setting If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in accordance with TV performance. Operation is performed on the front panel of the unit. You cannot perform the setting if the multizone function is not set to MULTI ZONE OFF (page 86 ). 1 Switch the receiver into standby. 2 While holding down ENTER on the front panel, press u STANDBY/ON. The display shows RESET c NO d. 3 Use i/j to select '4K/60p'. 4 Use k/l to select the signal to set. ! 4:4:4 - Select this setting when connecting to a 4K/60p 4:4:4 24 bit compatible TV using HDMI. More high quality video images can be enjoyed. - When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission), video image may not be output properly. In that case, select 4:2:0 to watch a 4K/60p 4:2:0 24 bit video image. - The HDMI OUT 3 terminal does not output a 4K/60p 4:4:4 24 bit video image if MAIN/HDZONE is set to HDZONE. ! 4:2:0 - Select this setting when connecting to a 4K/60p 4:2:0 24 bit compatible TV using HDMI. 5 When you're finished, press RETURN. 6 Press u STANDBY/ON to switch on the receiver and your TV. Make sure that the TV's video input is set to this receiver. Changing the channel level while listening Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system. 1 Press CH LV.. 2 Use i/j to select the channel you wish to adjust. 3 Adjust the volume using k/l. The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps. 4 When you're finished, press RETURN. Input Volume Absorber This can be used to correct for the difference in volume between input sources. 1 Switch to the input whose volume you want to adjust. 2 Press CH LV.. 3 Use i/j to select 'ALL'. 4 Adjust the volume using k/l. The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps. 5 When you're finished, press RETURN. 85