Pioneer VSX-36TX Owner's Manual - Page 36

Setup Menu.

Get Pioneer VSX-36TX PDF manuals and user guides View all Pioneer VSX-36TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Initial Set Up Î S0URCE MULTI OPERATION USE SETUP SYSTEM OFF RECEIVER DVD/LD TV/SAT VCR1 VCR2 MULTI CONTROL CD MD/ TAPE1 TUNER TVCONT CLASS MPX BAND DIRECT ACCESS ¶ 7 38 - + TUNING - + STATION 1¡ DTV ON/OFF DTV MENU 4¢ - + CHANNEL 123 456 7 GUIDE +10 + TV VOL - 8 0 TV TV CONTROL TV FUNC 9 EXIT ENTER DISC + VOLUME - REMOTE SETUP INPUT ATT SYSTEM SETUP EFFECT/ CH SEL MENU + MUTE FUNCTION DIGITAL NR ENTER - SIGNAL SELECT MIDNIGHT LIGHT MULTI CH INPUT THX DSP /DTS ADVANCED STEREO/ DIRECT STANDARD AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT 4 Adjust speaker levels so that you hear the test tone at the same volume from each speaker when seated in your main listening position. Note: The volume of the subwoofer tends to sound lower than it actually is, you may need to raise its level after testing the sound with actual soundtracks. In AUTO mode 1 Press the 2 or 3 button to adjust the level of the speaker outputting the TEST TONE. In MANUAL mode 1 Press the 2 or 3 button to adjust the level of the first speaker. 2 Press the 5/∞ button to switch the TEST TONE to the next speaker. 3 Repeat 1 and 2 for each speaker. If you are using a Sound Pressure Level (SPL) meter Take the readings from your main listening position and adjust the level of each speaker to 75 dB SPL (C-weighted/slow mode). 4-6 5 When you have adjusted each speaker level, press ENTER button to return to the previous screen. The MASTER VOLUME will return to its original position. 6 Select EXIT with the 5/∞ buttons and press ENTER button to return to the SYSTEM SETUP MENU. Next, proceed to CROSSOVER NETWORK on the next page. If you want to change a setting before proceeding simply use the arrow buttons to go back. memo Note that it is also possible to set channel levels temporarily. Then follow the same procedure as explained on this page. This function is designed to be used when you want to change the levels temporarily to raise the level of one channel. Using this method you can set speaker levels in different modes, such as, STEREO, and each DSP mode, independently. You should return the settings to their original state when done. Doing the set up procedures on this page will erase any temporary/independent level settings that have been made. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
36
4
Adjust speaker levels so that you hear the
test tone at the same volume from each
speaker when seated in your main listening
position.
Note: The volume of the subwoofer tends to sound lower than
it actually is, you may need to raise its level after testing the
sound with actual soundtracks.
In AUTO mode
1
Press the
2
or
3
button to adjust the level of the speaker
outputting the TEST TONE.
In MANUAL mode
1
Press the
2
or
3
button to adjust the level of the first
speaker.
2
Press
the
5
/
∞
button to switch the TEST TONE to the next
speaker.
3
Repeat
1
and
2
for each speaker.
If you are using a Sound Pressure Level (SPL) meter
Take the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighted/slow
mode).
5
When you have adjusted each speaker level,
press ENTER button to return to the
previous screen.
The MASTER VOLUME will return to its original position.
6
Select EXIT with the
5
/
∞
buttons and press
ENTER button to return to the SYSTEM
SETUP MENU.
Next, proceed to CROSSOVER NETWORK on the next page.
If you want to change a setting before proceeding
simply
use the arrow buttons to go back.
Note that it is also possible to set
channel levels temporarily. Then follow
the same procedure as explained on
this page. This function is designed to
be used when you want to change the
levels temporarily to raise the level of
one channel. Using this method you
can set speaker levels in different
modes, such as, STEREO,
and each
DSP mode, independently. You should
return the settings to their original
state when done. Doing the set up
procedures on this page will erase any
temporary/independent level settings
that have been made.
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
S0URCE
DVD/LD
TV/SAT
VCR1
VCR2
CD
TV VOL
TV FUNC
MENU
ENTER
STEREO/
DIRECT
DSP
THX
LIGHT
MUTE
TV
VOLUME
MD/
TAPE1
TUNER
TVCONT
RECEIVER
USE
SETUP
MULTI
OPERATION
CLASS
MPX
DIRECT ACCESS
CHANNEL
STATION
TV CONTROL
FUNCTION
REMOTE SETUP
SYSTEM SETUP
INPUT
ATT
MIDNIGHT
MULTI CH
INPUT
STANDARD
DIGITAL
NR
EFFECT/
CH SEL
SIGNAL
SELECT
BAND
SYSTEM
OFF
1
2
3
4
5
6
7
8
9
0
Î
8
7
3
1
¡
4
¢
+
-
+
-
+
-
MULTI CONTROL
+
+
–
–
+
–
4-6
ADVANCED
DISC
EXIT
+10
GUIDE
ENTER
/
DTS
DTV ON/OFF
DTV MENU
TUNING
Initial Set Up
memo