Pioneer VSX-C300 Operating Instructions - Page 14

Connecting Speakers - subwoofer

Get Pioneer VSX-C300 PDF manuals and user guides View all Pioneer VSX-C300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Connecting Your Equipment Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet. Connecting Speakers A full complement of five speakers is shown here but, naturally, everyone's home setup will vary. Simply connect the speakers you have in the manner described below. The receiver will work with just two stereo speakers (called "front" speakers in the diagram) but we recommend you use five speakers. If you don't hook up surround speakers you need to adjust the Listening mode settings (see page 30). Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal. Also make sure the positive and negative (+/-) terminals on the receiver match those on the speakers. MEMO: • Use speakers with a nominal impedance of 6 Ω to 16 Ω. Before hooking up your speakers affix the color-coded stickers with the appropriate names (for example, "front right") to the speaker wire so you always know which speaker each wire is connected to. While pressing down the speaker tab push the speaker wire into the terminal and release speaker terminal tab. R L DVD IN TV/ SAT IN DIGITAL (OPTICAL) VCR IN R L AUDIO 1 MONITOR OUT 2 ANTENNA AM LOOP FM UNBAL 75Ω R L VCR OUT VIDEO AUDIO SUB WOOFER OUT FRONT R L SPEAKERS CENTER SURROUND R L IN OUT CONTROL AC IN Audio cord (sold separately) Speaker wire (sold separately) ANALOG IN When you're hooking up your subwoofer make sure its power cord is disconnected. Powered FRONT R FRONT L Subwoofer (SW) (FR) (FL) CENTER SURROUND SURROUND (C) R (SR) L (SL) Speaker terminals Use good quality speaker wire to connect the speakers to the receiver. 1 Twist about 10 mm of bare wire strands together. 2 Push in the speaker terminal tab and insert the wire. 3 Release speaker terminal tab, it should snugly grip the speaker wire. ª · 10 mm Caution: Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the 14 bare speaker wire touches the back panel it may cause the power to cut off as a safety measure. En Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
14
En
DVD
IN
VCR
IN
VCR
OUT
MONITOR
OUT
TV/
SAT
IN
DIGITAL
(OPTICAL)
AUDIO
AUDIO
FM UNBAL 75
Ω
AM LOOP
ANTENNA
VIDEO
R
L
1
2
R
L
R
L
SUB
WOOFER
OUT
FRONT
R
L
SURROUND
R
L
CENTER
IN
OUT
CONTROL
AC
IN
SPEAKERS
ANALOG
IN
Caution:
Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the
bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.
Speaker terminals
Use good quality speaker wire to connect the speakers to the receiver.
1
Twist about 10 mm of bare wire strands together.
2
Push in the speaker terminal tab and insert the wire.
3
Release speaker terminal tab, it should snugly grip the speaker wire.
ª
·
10 mm
Before hooking up your speakers
affix the color-coded stickers with
the appropriate names (for
example,
“
front right
”
) to the
speaker wire so you always know
which speaker each wire is
connected to.
While pressing down the
speaker tab push the
speaker wire into the
terminal and release
speaker terminal tab.
When you
’
re
hooking up your
subwoofer make
sure its power cord
is disconnected.
Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall
outlet.
Connecting Speakers
A full complement of five speakers is shown here but, naturally, everyone
’
s home setup will vary. Simply connect the
speakers you have in the manner described below. The receiver will work with just two stereo speakers (called
“
front
”
speakers in the diagram) but we recommend you use five speakers. If
you don
’
t hook up surround speakers
you
need to adjust the Listening mode settings (see page 30).
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal.
Also make sure the positive and negative (+/
–
) terminals on the receiver match those on the speakers.
MEMO:
•
Use speakers with a nominal impedance of 6
Ω
to 16
Ω
.
Powered
Subwoofer (SW)
FRONT R
(FR)
FRONT L
(FL)
SURROUND
R (SR)
SURROUND
L (SL)
CENTER
(C)
Connecting Your Equipment
Audio cord
(sold separately)
Speaker wire
(sold separately)
Downloaded from
www.Manualslib.com
manuals search engine