Reebok 1000 X Elliptical English Manual - Page 7

Tip: Avoid pinching the Wire Harness

Get Reebok 1000 X Elliptical PDF manuals and user guides View all Reebok 1000 X Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

3. Identify the Upright (3) and orient it as shown. Then, pull the Pulse Wire (64) out of the top of 3 the Upright. While a second person holds the Upright (3) near the top of the Frame (1), slide the Upright Cover (6) upward onto the Upright. Have the second person hold the Upright Cover around the Upright until step 5. 64 3 1 6 4. Note: For clarity, the Upright Cover (6) is not shown in the drawing. Have the second person hold the Upright (3) and the Upright Cover near the top of the Frame (1). Locate the wire tie (see the inset drawing) in the Upright. Tie the lower end of the wire tie to the Wire Harness (46). Next, pull the upper end of the wire tie upward out of the top of the Upright. Then, untie and discard the wire tie. Tip: Do not allow the ends of the wires to fall into the Upright. Use a piece of tape or an elastic band to hold the wires in place until step 6. Slide the Upright (3) onto the Frame (1). Attach the Upright with four M8 x 19mm Patch Screws (85). Tip: Avoid pinching the Wire Harness (46) during this step. 4 64 46 85 1 Avoid pinching the Wire Harness (46) during this step Wire Tie 46 3 85 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
7
3.
Identify the Upright (3) and orient it as shown.
Then, pull the Pulse Wire (64) out of the top of
the Upright.
While a second person holds the Upright (3)
near the top of the Frame (1), slide the Upright
Cover (6) upward onto the Upright.
Have the
second person hold the Upright Cover
around the Upright until step 5.
4.
Note: For clarity, the Upright Cover (6) is not
shown in the drawing.
Have the second per-
son hold the Upright (3) and the Upright Cover
near the top of the Frame (1). Locate the wire
tie (see the inset drawing) in the Upright. Tie the
lower end of the wire tie to the Wire Harness
(46). Next, pull the upper end of the wire tie
upward out of the top of the Upright. Then, untie
and discard the wire tie.
Tip: Do not allow the
ends of the wires to fall into the Upright. Use
a piece of tape or an elastic band to hold the
wires in place until step 6.
Slide the Upright (3) onto the Frame (1). Attach
the Upright with four M8 x 19mm Patch Screws
(85).
Tip: Avoid pinching the Wire Harness
(46) during this step.
3
46
64
64
6
3
1
3
1
85
85
Avoid pinching the
Wire Harness (46)
during this step
4
Wire Tie
46