Ricoh Aficio SP 9100DN Hardware Guide - Page 98

Call Service: EC Power Off On/Call Service if error reoccurs, Add staples Booklet: Back

Get Ricoh Aficio SP 9100DN PDF manuals and user guides View all Ricoh Aficio SP 9100DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

9. Troubleshooting The printer is out of the staple. • Add staples, cancel staples mode or cancel the job. • See p.81 . Add staples (Booklet) Both staplers of the Booklet Finisher is out of staples. • Add staples to the both staplers of the Booklet Finisher. • See p.81 . • Alternatively, cancel the staple mode using [Form Feed], or cancel the job. Add staples (Booklet: Back) The back stapler of the Booklet Finisher is out of staples. • Add staples to the back stapler of the Booklet Finisher. • See p.81 . • Alternatively, cancel the staple mode using [Form Feed], or cancel the job. Add staple (Booklet: Front) The front stapler of the Booklet Finisher is out of staples. • Add staples to the front stapler of the Booklet Finisher. • See p.81 . • Alternatively, cancel the staple mode using [Form Feed], or cancel the job. Add Toner 9 The printer is out of toner. • Replace the toner bottle. • See p.81 . Call Service: EC Power Off On/Call Service if error reoccurs A communication error was sent from the engine to the controller. • Turn the power switch to Standby, and then to ON. If the message appears again, call your sales / service representative. Cannot check Signal in Ad hoc An attempt to check the radio signal was made while the communication mode was set to [802.11 Ad hoc] in the [Maintenance] menu. • To check the radio signal, select Infrastructure in the communication mode settings. Cannot duplex Tray # The selected tray is set to 1 sided tray when duplex mode is set. 96

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
The printer is out of the staple.
•
Add staples, cancel staples mode or cancel the job.
•
See p.81 .
Add staples (Booklet)
Both staplers of the Booklet Finisher is out of staples.
•
Add staples to the both staplers of the Booklet Finisher.
•
See p.81 .
•
Alternatively, cancel the staple mode using [Form Feed], or cancel the job.
Add staples (Booklet: Back)
The back stapler of the Booklet Finisher is out of staples.
•
Add staples to the back stapler of the Booklet Finisher.
•
See p.81 .
•
Alternatively, cancel the staple mode using [Form Feed], or cancel the job.
Add staple (Booklet: Front)
The front stapler of the Booklet Finisher is out of staples.
•
Add staples to the front stapler of the Booklet Finisher.
•
See p.81 .
•
Alternatively, cancel the staple mode using [Form Feed], or cancel the job.
Add Toner
The printer is out of toner.
•
Replace the toner bottle.
•
See p.81 .
Call Service: EC Power Off On/Call Service if error reoccurs
A communication error was sent from the engine to the controller.
•
Turn the power switch to Standby, and then to ON. If the message appears again, call your sales /
service representative.
Cannot check Signal in Ad hoc
An attempt to check the radio signal was made while the communication mode was set to [802.11 Ad
hoc] in the [Maintenance] menu.
•
To check the radio signal, select Infrastructure in the communication mode settings.
Cannot duplex Tray #
The selected tray is set to 1 sided tray when duplex mode is set.
9. Troubleshooting
96
9