Samsung SRP-350PG Service Manual - Page 43

Maintenance and Adjustments

Get Samsung SRP-350PG - SRP 350 B/W Direct Thermal Printer PDF manuals and user guides View all Samsung SRP-350PG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

5 Maintenance and Adjustments 5-1 Adjustment 5-1-1 Remaining Roll Paper Adjustment This sensor is set to the step3 position at the factory. If you find that there is not or too enough paper remaining on the roll when the near-end sensor is triggered, you can change the setting to the upper or Lower position as described below. Note : The factory setting is based on a paper roll core with an outside diameter of 18mm. If you use a paper roll with a cor e with an outside diameter of mor e than 18mm, it is better to change to the upper position (Rotate the tab at front side) as described below. 1. Open the paper roll cover. 2. Rotate the tab at front or rear Position. Near end sensor tab Figure 5-1 Adjusting the Paper Near End Sensor Note : For your r eference, this shows the diameter at which the near-end sensor is triggered. Note that this figur e is a calculated value, and there may be some variations depending on the printer. Figure 5-2 Paper Remaining Amount for Paper Spool Diameter Samsung Electro-Mechanics 5-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Near end sensor tab
5-1
5
Maintenance and Adjustments
5-1-1 Remaining Roll Paper Adjustment
Figure 5-1 Adjusting the Paper Near End Sensor
Note :
The factory setting is based on a paper roll core with an outside diameter of 18mm.
If you use a paper roll
with a cor e with an outside diameter of mor e than 18mm, it is better to change to the upper position
1. Open the paper
5-1
5
Maintenance and Adjustments
5-1-1 Remaining Roll Paper Adjustment
Figure 5-1 Adjusting the Paper Near End Sensor
Note :
The factory setting is based on a paper roll core with an outside diameter of 18mm.
If you use a paper roll
with a cor e with an outside diameter of mor e than 18mm, it is better to change to the upper position
5-1
5
Maintenance and Adjustments
5-1-1 Remaining Roll Paper Adjustment
Figure 5-1 Adjusting the Paper Near End Sensor
Note :
The factory setting is based on a paper roll core with an outside diameter of 18mm.
If you use a paper roll
with a cor e with an outside diameter of mor e than 18mm, it is better to change to the upper position
5-1
5
Maintenance and Adjustments
5-1 Adjustment
5-1-1 Remaining Roll Paper Adjustment
Figure 5-1 Adjusting the Paper Near End Sensor
Figure 5-2 Paper Remaining Amount for Paper Spool Diameter
Note :
The factory setting is based on a paper roll core with an outside diameter of 18mm.
If you use a paper roll
with a cor e with an outside diameter of mor e than 18mm, it is better to change to the upper position
Note :
For your reference, this shows the diameter at which the near-end sensor is triggered. Note that this figure
is a calculated value, and there may be some variations depending on the printer.
This sensor is set to the
position at the
.
Samsung Electro-M
e
chanics