Sanyo PDG-DXL2000 Owners Manual - Page 69

Appendix, Troubleshooting

Get Sanyo PDG-DXL2000 - 2000 Lumens PDF manuals and user guides
UPC - 086483079436
View all Sanyo PDG-DXL2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. - Make sure you have properly connected the projector to peripheral equipment as described on pages 16-18. - Make sure all equipment is connected to AC outlet and the power is turned on. - When the projector does not project an image from the connected computer, restart the computer. Power Opening display Problem Solutions No power q Plug the power cord of the projector into the AC outlet. q See if the POWER indicator lights red. q Wait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red. q Check the WARNING indicator. If the WARNING TEMP. indicator lights red, projector can not be turned on. q Check the projection lamp. q Unlock the Key lock function for the projector. PIN code dialog box appears at q PIN code lock is being set. Enter a PIN code (the "1234" or start-up. numbers you have set.) The initial display is not shown. q Make sure Off or Countdown off are not chosen at display function. The initial display is not same q Make sure User or Off are not chosen at Logo (select) as the default set. function. Input signal switches automati- q Make sure Input search function is adjusted properly. cally. (or does not switch automatically) An icon other than Input mode q That is the Filter warning icon or the Lamp replacement icon. or Lamp mode icon appears No image q Check the connection between your computer or video equipment and the projector. q See if the input signal is correctly output from your computer. Some laptop computers may need to change the setting for monitor output when connecting to a projector. See your computer's instruction manual for the setting. q It takes about 30 seconds to display an image after turning on the projector. q Check the Input signal, color system, video system or computer system mode. q Make sure the temperature is not out of the specified Operating Temperature (41˚F-95˚F [5˚C-40˚C]). q When No Show is operating, the image can not be displayed. Press the NO SHOW button or any other button on the remote control. Image is Left/Right reversed. q Check the Ceiling/Rear function. Image is Top/Bottom reversed. q Check the Ceiling function. Pages 20 64 67 59 21, 59-60 53 53 51 62, 67 16-18 20 40, 47 40, 47 Image 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
69
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described on pages 16-18.
– Make sure all equipment is connected to AC outlet and the power is turned on.
– When the projector does not project an image from the connected computer, restart the computer.
Problem
Solutions
Pages
Power
No power
q
Plug the power cord of the projector into the AC outlet.
q
See if the POWER indicator lights red.
q
Wait until the POWER indicator stops blinking to turn on the
projector again. The projector can be turned on after the
POWER indicator turns red.
20
q
Check the WARNING indicator. If the WARNING TEMP.
indicator lights red, projector can not be turned on.
64
q
Check the projection lamp.
67
q
Unlock the Key lock function for the projector.
59
PIN code dialog box appears at
start-up.
q
PIN code lock is being set. Enter a PIN code (the “1234” or
numbers you have set.)
21,
59-60
Opening display
The initial display is not shown.
q
Make sure
Off
or
Countdown off
are not chosen at display
function.
53
The initial display is not same
as the default set.
q
Make sure
User
or
Off
are not chosen at Logo (select)
function.
53
Input signal switches automati-
cally. (or does not switch auto-
matically)
q
Make sure Input search function is adjusted properly.
51
An icon other than Input mode
or Lamp mode icon appears
q
That is the Filter warning icon or the Lamp replacement icon.
62, 67
Image
No image
q
Check the connection between your computer or video
equipment and the projector.
16-18
q
See if the input signal is correctly output from your computer.
Some laptop computers may need to change the setting for
monitor output when connecting to a projector. See your
computer’s instruction manual for the setting.
q
It takes about 30 seconds to display an image after turning on
the projector.
20
q
Check the Input signal, color system, video system or
computer system mode.
q
Make sure the temperature is not out of the specified
Operating Temperature (41˚F–95˚F [5˚C–40˚C]).
q
When
No Show
is operating, the image can not be displayed.
Press the NO SHOW button or any other button on the remote
control.
Image is Left/Right reversed.
q
Check the Ceiling/Rear function.
40, 47
Image is Top/Bottom reversed.
q
Check the Ceiling function.
40, 47