Sanyo PDG-DXL2000 Owners Manual - Page 76

Appendix When the input signal is digital from HDMI terminal, refer to the chart below. ON-SCREEN RESOLUTION H-FREQ. DISPLAY [kHz] D-VGA D-480i D-480p D-575i D-575p D-SVGA D-SVGA D-XGA D-XGA D-WXGA 3 D-WXGA 6 D-WXGA 7 D-WXGA 8 D-WXGA 9 D-WXGA 10 D-WXGA 11 D-WXGA 13 D-WXGA 14 D-WXGA 15 D-SXGA 1 D-SXGA 2 D-SXGA+ 2 640x480 720x480 i 720x480 i 720x480 720x480 720x575 i 720x575 i 720x575 720x575 800x600 800x600 1024x768 1024x768 1376x768 1280x768 1280x768 1280x768 1280x800 1280x800 1280x800 1360x768 1280x768 1280x800 1280x1024 1280x1024 1400x1050 31.469 15.734 31.469 31.469 62.937 15.625 31.250 31.250 62.500 37.879 76.302 43.363 97.551 48.360 47.776 60.289 68.633 49.600 41.200 49.702 97.533 97.396 101.563 63.980 60.276 65.350 V-FREQ. [Hz] 59.940 59.940 119.880 59.940 119.880 50.00 100.00 50.000 100.00 60.320 119.972 60.000 119.989 60.000 59.870 74.893 84.837 60.050 50.000 59.810 119.967 119.798 119.909 60.020 58.069 60.120 3D DISPLAY 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 - ON-SCREEN RESOLUTION H-FREQ. V-FREQ. 3D DISPLAY [kHz] [Hz] DISPLAY D-SXGA+ 2 1400x1050 65.120 59.900 - D-SXGA+ 5 1400x1050 62.500 58.600 4 D-SXGA+ 6 1400x1050 64.744 59.948 4 D-SXGA+ 2 1400x1050 65.317 59.978 4 D-UXGA 1 1600x1200 75.000 60.000 4 D-WUXGA 2 1920 x 1200 74.038 59.950 - D-WSXGA+ 1 1680 x 1050 65.290 59.954 - D-WXGA+ 1 1440 x 900 55.935 59.887 4 1280x720 45.000 60.000 4 D-720p 1280x720 37.500 50.000 4 1280x720 90.000 120.000 4 1280x720 75.000 100.000 4 1920x1080 i 33.750 59.94/60 4 D-1080i 1920x1080 i 28.125 50.000 4 1920x1080 i 67.500 119.98/120 4 1920x1080 i 56.250 100.000 4 1920x1080 33.750 30.000 - 1920x1080 28.125 25.000 - D-1080p 1920x1080 27.000 24.000 - 1920x1080 67.500 60.000 - 1920x1080 56.250 50.000 - 4Note: • The mark "4" indicates that the 3D image can be projected. • Alphabet letter "i" placed beside some of the resolutions represents interlace signal. • The specifications are subject to change without notice. • Depending on your PC settings, the digital signals of your PC may not be projected correctly. In such a case, confirm your PC settings. • When you project a DVI signal, connect the cables, turn the projector on, then select the input. Finally, turn on your PC. Be sure to follow this procedure, otherwise an image may not be projected on the screen. If an image is not projected correctly, restart your PC. • Do not disconnect the cable while the projector is running. If the cable has been disconnected and then reconnected, an image may not be correctly projected. 76