Sanyo XU86 Instruction Manual, PLC-XU86 Network Set Up - Page 45

Parameter, Description, IP Address, Subnet Mask, and Gateway Address fields will be displayed

Get Sanyo XU86 - PLC XGA LCD Projector PDF manuals and user guides View all Sanyo XU86 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

6. Configurations with Browser Parameter Description Projector Name each projector to distinguish it from other projectors. (up to 32 one-byte characters). The name set here will be displayed on the Network Projector List in the application operation screen. IP Configured Method A desired IP address setup method is selected from "Manual", "DHCP", and "BOOTP". If "DHCP" or "BOOTP" is selected, the IP address is obtained automatically as "DHCP client" or "BOOTP client". At this time, it is necessary that the DHCP server/BOOTP server must be in the environment allowing the network communication. IP Address, Subnet Mask, and Gateway Address fields will be displayed "-.-.-.-", when the IP Address Configuration Method is set to DHCP or BOOTP and failed to get the figures from the DHCP server, the computer cannot be connected to the projector. If the projector fails to obtain IP address from BOOTP server, the existing IP address will be assigned. IP Address Set the IP address in the environment you wish to use. If "IP Configuration Method" is set to "DHCP" or "BOOTP", this setting is not needed. Subnet Mask Set the Subnet mask in the environment you wish to use. If "IP Configuration Method" is set to "DHCP" or "BOOTP", this setting may become unnecessary depending on the settings of "DHCP Server" and "BOOTP Server". Gateway Address Set the gateway address in the environment you wish to use. If "IP Configuration Method" is set at "DHCP" or "BOOTP", this setting may become unnecessary depending on the settings of "DHCP Server" and "BOOTP Server". If any segment beyond the router is not used, the gateway address can be remained "255.255.255.255". Wireless Mode Select the Communication mode 802.11b or 802.11b.g Network Type Select either "Infrastructure" or "AdHoc". SSID Set the SSID/ESSID. (up to ASCII 32 characters) SSID/ESSID is case-sensitive. Even though all characters projected in Wired/Wireless information are uppercase, it is necessary to distinguish between upper case and lower case characters. APPLY button Click the APPLY button to update. The screen to restart the projector will be displayed. REFRESH button Update and show the adjusted data. RESTORE Factory Default Settings button ..........Restore the settings to the values at the factory. English * Not displayed at Wired LAN setting. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
45
6. Configurations with Browser
* Not displayed at Wired LAN setting.
Parameter
Description
Projector
..........................................
Name each projector to distinguish it from other projectors. (up to 32
one-byte characters). The name set here will be displayed on the
Network Projector List in the application operation screen.
IP Configured Method
....................
A desired IP address setup method is selected from "Manual", "DHCP",
and "BOOTP".
If "DHCP" or "BOOTP" is selected, the IP address is obtained
automatically as "DHCP client" or "BOOTP client".
At this time, it is
necessary that the DHCP server/BOOTP server must be in the
environment allowing the network communication.
IP Address, Subnet Mask, and Gateway Address fields will be displayed
"-.-.-.-", when the IP Address Configuration Method is set to DHCP or
BOOTP and failed to get the figures from the DHCP server, the
computer cannot be connected to the projector.
If the projector fails to obtain IP address from BOOTP server, the
existing IP address will be assigned.
IP Address
......................................
Set the IP address in the environment you wish to use.
If "IP Configuration Method" is set to "DHCP" or "BOOTP", this setting is
not needed.
Subnet Mask
..................................
Set the Subnet mask in the environment you wish to use.
If "IP Configuration Method" is set to "DHCP" or "BOOTP", this setting
may become unnecessary depending on the settings of "DHCP Server"
and "BOOTP Server".
Gateway Address
............................
Set the gateway address in the environment you wish to use.
If "IP Configuration Method" is set at "DHCP" or "BOOTP", this setting
may become unnecessary depending on the settings of "DHCP Server"
and "BOOTP Server".
If any segment beyond the router is not used, the gateway address can
be remained “255.255.255.255”.
Wireless Mode*
..............................
Select the Communication mode 802.11b or 802.11b.g
Network Type*
................................
Select either “Infrastructure” or “AdHoc”.
SSID*
..............................................
Set the SSID/ESSID. (up to ASCII 32 characters)
SSID/ESSID is case-sensitive.
Even though all characters projected in
Wired/Wireless information are uppercase, it is necessary to distinguish
between upper case and lower case characters.
APPLY button
..................................
Click the APPLY button to update. The screen to restart the projector will be
displayed.
REFRESH button
............................
Update and show the adjusted data.
RESTORE Factory Default
Settings button
..........
Restore the settings to the values at the factory.
English