Sharp AL-1670 AL-1670 Operation Manual - Page 59

Self-diagnostic function

Get Sharp AL-1670 - B/W Laser - Copier PDF manuals and user guides View all Sharp AL-1670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

COPIER TROUBLE? Problem Power is on but copying is not possible. Solution q Is the POWER SAVE ( ) indicator blinking? Wait until warm-up is complete. Warm-up time is approximately 35 seconds. q Is the indicator on? Copy paper is needed. See page 13, LOADING COPY PAPER. q Is blinking in the copy quantity display? The TD cartridge is not installed. Install the TD cartridge. q Is steadily lit in the copy quantity display? Side cover(s) is open. Close the front and side covers securely. q Is the indicator blinking? The TD cartridge must be replaced. See page 39, TD CARTRIDGE REPLACEMENT. Lighting fixture flickers. q Is the indicator blinking? A misfeed has occurred. See page 43, MISFEED REMOVAL. q Is the same power outlet used for the lighting fixture and the copier? Connect the copier to a power outlet which is not used for other electric appliances. Be sure to use only genuine SHARP parts and supplies. Please contact your SHARP service center immediately if a problem persists after checking the above. Self-diagnostic function An automatic self-diagnostic function is built into the copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage. An alphanumeric code will appear in the copy quantity display. Example Should the copier completely stop and a letter and a number appear alternately, contact your SHARP service center immediately. 57 Copier trouble? GENERAL INFORMATION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
57
GENERAL INFORMATION
The TD cartridge is not installed. Install the
TD cartridge.
Side cover(s) is open.
Close the front and side covers securely.
The TD cartridge must be replaced. See page
39, TD CARTRIDGE REPLACEMENT.
A misfeed has occurred. See page 43,
MISFEED REMOVAL.
Connect the copier to a power outlet which is
not used for other electric appliances.
●
Is
blinking in the copy
quantity display?
●
Is
steadily lit in the copy
quantity display?
●
Is the
indicator blinking?
●
Is the
indicator blinking?
●
Is the same power outlet used for
the lighting fixture and the copier?
Self-diagnostic function
An automatic self-diagnostic function is built into the copier. Should the
copier malfunction, the self-diagnostic function will locate the problem and
stop the copier to prevent damage. An alphanumeric code will appear in the
copy quantity display.
Example
Should the copier completely stop and a letter and a number appear alternately,
contact your SHARP service center immediately.
Be sure to use only genuine SHARP parts and supplies.
Please contact your SHARP service center immediately if a problem persists
after checking the above.
Problem
Solution
●
Is the POWER SAVE (
)
indicator blinking?
●
Is the
indicator on?
Wait until warm-up is complete.
Warm-up time is approximately 35 seconds.
Copy paper is needed. See page 13, LOADING
COPY PAPER.
Power is on but copying
is not possible.
Copier trouble?
COPIER TROUBLE?
Lighting fixture flickers.