Sharp AL-1670 AL-1670 Operation Manual - Page 62

Moving Instructions

Get Sharp AL-1670 - B/W Laser - Copier PDF manuals and user guides View all Sharp AL-1670 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

MOVING INSTRUCTIONS When moving this copier, follow the procedure below. When moving this copier, be sure to remove the TD cartridge in advance. 1 Turn the power switch off and disconnect the power cord. 2 Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. Push gently the right side of the front cover to open the cover. Moving instructions TD cartridge lock release lever 3 Lift the TD cartridge lock release lever and pull the cartridge out until the green strap handle can be grasped by the right hand. Lift the cartridge by the handle while supporting it with the left hand at the green label position to remove it. 4 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. 5 Gently lift and pull out the paper tray until it stops. 6 Push the center of the pressure plate down until it locks in place and lock the plate using the pressure plate lock which has been stored in the front of the paper tray. 7 Use a coin (or suitable object) to attach to the left side of the copier the screw that has been stored in the front of the paper tray. When shipping the copier, the screw must be reinstalled to prevent shipping damage. 8 Push the paper tray back into the copier. q Repeat steps 5, 6, and 8 for both the upper and lower trays. 9 Close the bypass tray. Attach the packing materials and tape which were removed during installation of the copier. See page 11, SET-UP. 10 Pack the copier into the carton. See page 10, CHECKING PACKED COMPONENTS AND ACCESSORIES. 60 GENERAL INFORMATION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
60
GENERAL INFORMATION
MOVING INSTRUCTIONS
When moving this copier, follow the procedure below.
When moving this copier, be sure to remove the TD cartridge in advance.
1
Turn the power switch off and disconnect the power
cord.
2
Open the bypass tray. Lift slightly on the side cover
and slide the cover out until it stops.
Push gently the
right side of the front cover to open the cover.
3
Lift the TD cartridge lock release lever and pull the
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
4
Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover.
When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
5
Gently lift and pull out the paper tray until it stops.
6
Push the center of the pressure plate down until it locks
in place and lock the plate using the pressure plate lock
which has been stored in the front of the paper tray.
7
Use a coin (or suitable object) to attach to the left side of
the copier the screw that has been stored in the front of
the paper tray.
When shipping the copier, the screw must be rein-
stalled to prevent shipping damage.
8
Push the paper tray back into the copier.
●
Repeat steps 5, 6, and 8 for both the upper and lower trays.
9
Close the bypass tray. Attach the packing materials and
tape which were removed during installation of the
copier. See page 11, SET-UP.
10
Pack the copier into the carton. See page 10, CHECKING
PACKED COMPONENTS AND ACCESSORIES.
Moving instructions
TD cartridge lock
release lever