Sharp AM 900 AM-900 Online Guide

Sharp AM 900 - Digital Office Laser Copier Manual

Get Sharp AM 900 - Digital Office Laser Copier PDF manuals and user guides
UPC - 074000034068
View all Sharp AM 900 manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp AM 900 manual content summary:

  • Sharp AM 900 | AM-900 Online Guide - Page 1
    MODEL AM-900 DIGITAL MULTIFUNCTIONAL SYSTEM ONLINE GUIDE 1. Installation 2. Copying 3. Sending Faxes 4. Receiving Faxes 5. Special Fax Functions 6. Printing 7. Scanning 8. Printing Lists 9. Maintenance 10. Troubleshooting
  • Sharp AM 900 | AM-900 Online Guide - Page 2
    refer to the appropriate instructions in the operation manual." As an ENERGY STAR“ partner, SHARP has determined that this product meets the ENERGY STAR“ guidelines for energy efficiency. Declaration of Conformity SHARP DIGITAL MULTIFUNCTIONAL SYSTEM, AM-900 This device complies with Part 15 of the
  • Sharp AM 900 | AM-900 Online Guide - Page 3
    you for choosing a Sharp MFP! The MFP is a combination monochrome printer, copier, fax, and color scanner. The features and specifications of the MFP are shown below. Print specifications Printer type Toner cartridge yield* (continuous printing, 5% page coverage, letter paper) Drum cartridge yield
  • Sharp AM 900 | AM-900 Online Guide - Page 4
    time* Approx. 3 seconds Communication method Super G3, G3 Compression scheme MMR, MR, MH Memory Scanner type CIS (Contact Image Sensor) Resolution 300/600 x 300 dpi, 300/600 x 600 dpi Scan speed Black and white: (TWAIN scanning using 300/600 x 300 dpi: 6 sec/page the auto document feeder
  • Sharp AM 900 | AM-900 Online Guide - Page 5
    ) Depth: 16.5" (420 mm) Height: 14.6" (370 mm) Weight Approx. 28.0 lbs. (12.7 kg) (including trays and toner and drum cartridges) As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The
  • Sharp AM 900 | AM-900 Online Guide - Page 6
    Important safety information • Do not disassemble this machine or attempt any procedures not described in this manual. Refer all servicing to qualified service personnel. • Do not install or use the machine near water, or when you are wet. For example, do not use the machine near a bath tub, wash
  • Sharp AM 900 | AM-900 Online Guide - Page 7
    information • Sharpdesk is a trademark of Sharp Corporation. • Microsoft, Windows and Internet Explorer are trademarks of Microsoft Corporation in the U.S.A. and other countries. • Acrobat and Adobe are trademarks of Adobe Systems Incorporated. • Eastman Software is a trademark of Eastman Kodak
  • Sharp AM 900 | AM-900 Online Guide - Page 8
    of Contents A Look at the Operation Panel 8 1. Installation 10 Unpacking Checklist 10 Installation 11 Installing the Toner Cartridge and Drum Cartridge 16 Loading Printing Paper 21 Installing the Software 23 Using the Machine as a Shared Printer on a Network 30 Entering Your Name and Fax
  • Sharp AM 900 | AM-900 Online Guide - Page 9
    From the Scanner Wizard (Windows XP/Me only) . . . . . 117 Scanning From the Operation Panel 118 8. Printing Lists 126 9. Maintenance 131 Cleaning the Scanning Glasses and Rollers 131 Replacing the Toner Cartridge 135 Replacing the Drum Cartridge 136 10. Troubleshooting 139 Problems and
  • Sharp AM 900 | AM-900 Online Guide - Page 10
    A Look at the Operation Panel 1 234 5 6 78 9 COPY SCAN FAX HELP QUALITY E-SORT MENU CONTRAST REDIAL ZOOM Z A BROADCAST ! DUPLEX SCAN PRINT STOP ENTER SPEED 10 11 12 13 14 15 16 17 18 19 20 21 1 Display This displays messages and prompts to help you operate the machine. 2 ZOOM
  • Sharp AM 900 | AM-900 Online Guide - Page 11
    drum cartridge is near or at the end of its life. This lights steadily when the toner cartridge is empty, the machine is out of paper, the print compartment cover is open, or when a paper jam has occurred (a message will appear to indicate the problem using an abbreviated 2-digit Speed Dial number (
  • Sharp AM 900 | AM-900 Online Guide - Page 12
    1. Installation Unpacking Checklist Before setting up, make sure you have all of the following items. If any are missing, contact your dealer or retailer. Telephone line cord Toner cartridge Drum cartridge Output tray Document feeder tray Setup Guide Points to keep in mind when setting up
  • Sharp AM 900 | AM-900 Online Guide - Page 13
    1. Installation Installation Attaching the trays Attach the document feeder tray. Installation Slide the output tray into the machine as shown. When it stops, lift the end slightly and push in so that the tray locks in place. If you will be using legal paper, pull out the tray extension Important
  • Sharp AM 900 | AM-900 Online Guide - Page 14
    Installation Releasing the scanner Before plugging in the power cord, pull the scanner release toward you to release the scanner lock. i Caution: Plugging in the power cord without releasing the scanner lock may damage the machine. If you need to move the machine: i In the event that you need to
  • Sharp AM 900 | AM-900 Online Guide - Page 15
    1. Installation Installation Connecting the power cord Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet. i Caution: Make sure the scanner has been released as explained on the previous page before plugging in the power cord. i Do not plug the power cord into any other kind
  • Sharp AM 900 | AM-900 Online Guide - Page 16
    Installation Connecting the telephone line cord Insert one end of the line cord into the socket on the back of the machine marked TEL. LINE. Insert the other end into a wall telephone socket.
  • Sharp AM 900 | AM-900 Online Guide - Page 17
    the facsimile function in conjunction with any of these services, you may experience errors during transmission and reception of facsimile messages. i The facsimile function of this machine is not compatible with digital telephone systems. Extension phone (optional) If desired, you can connect an
  • Sharp AM 900 | AM-900 Online Guide - Page 18
    and Drum Cartridge The laser printer in the machine uses a toner cartridge and a drum cartridge. i The starter toner cartridge included with the machine can print approximately 1,500 letter-size pages at 5% page coverage. i When replacing the toner cartridge, use a SHARP AM-90ND toner cartridge. One
  • Sharp AM 900 | AM-900 Online Guide - Page 19
    1. Installation Installing the Toner Cartridge and Drum Cartridge 2 Remove the new drum cartridge from its packaging. 3 Insert the drum cartridge into the print compartment, sliding it along the guides. x Do not touch or allow other objects to contact the drum (the green cylinder). This may
  • Sharp AM 900 | AM-900 Online Guide - Page 20
    Installing the Toner Cartridge and Drum Cartridge 5 Grasp the cartridge handle and insert the toner cartridge into the print compartment, sliding it along the guides. x After inserting the cartridge, press on the arrow mark to make sure it "clicks" into place. x Do not touch the roller in the toner
  • Sharp AM 900 | AM-900 Online Guide - Page 21
    not alert you when the toner cartridge is out of toner.) 8 Press . 9 If you installed a new drum cartridge, reset the drum counter as explained below. Resetting the drum counter Each time you install a new drum cartridge, follow the steps below to reset the drum counter to zero. 1 Press MENU
  • Sharp AM 900 | AM-900 Online Guide - Page 22
    Cartridge and Drum Cartridge Manually resetting the toner counter When a new toner cartridge is installed, the toner counter is reset in Step 7 on the previous page. The procedure below is normally not necessary; however, it can be used in the event that you need to reset the toner counter manually
  • Sharp AM 900 | AM-900 Online Guide - Page 23
    1. Installation Loading Printing Paper Loading Printing Paper You can load up to 250 sheets of letter or legal paper (max. 20 lbs.) in the paper tray. Caution! Do not use the blank side of paper that has already been printed on. 1 Remove the output tray. 2 Insert a stack of paper into the tray,
  • Sharp AM 900 | AM-900 Online Guide - Page 24
    Loading Printing Paper 4 Replace the output tray. x If you loaded legal size paper (or you changed the paper size), change the paper size setting as explained below. Setting the paper size The
  • Sharp AM 900 | AM-900 Online Guide - Page 25
    1. Installation Installing the Software Installing the Software To use the machine as a printer and scanner for your computer, you must install the software and connect a USB cable. The CD-ROM that comes with the machine contains the following software: i MFP Drivers: These consist of the printer
  • Sharp AM 900 | AM-900 Online Guide - Page 26
    Installing the Software i To scan a legal size document (the maximum size) at 1200 dpi in full color, at least 1 GB of memory is required. In addition, at least 600 MB or more of free hard disk space is required on the drive where your operating system is installed. In Windows“ Me, it is not
  • Sharp AM 900 | AM-900 Online Guide - Page 27
    and click Next (the language selections will vary depending on your country or region). 6. Follow the instructions in the windows that appear. i When the Setup Type Selection window appears, select Standard to install all software components (this should normally be selected). If you only wish to
  • Sharp AM 900 | AM-900 Online Guide - Page 28
    the Software 7. When the Finish window appears to indicate that the selected packages have been installed, click Close. 8. If the installation was a Standard installation, the following window will appear. Click OK. i If you installed the MFP drivers using a Custom installation and did not install
  • Sharp AM 900 | AM-900 Online Guide - Page 29
    1. Installation Installing the Software 10. The Search Setup Wizard will appear. Follow the on-screen instructions to create an index database for Sharpdesk. 11. Make sure that the power cord of the machine is not plugged in (the machine is powered off), and then connect the USB cable. i Insert one
  • Sharp AM 900 | AM-900 Online Guide - Page 30
    Installing the Software Comments: i Do not connect the AM-900 to a hub to which another AM-900 is connected. If this is done, the AM-900 will not operate correctly. i If you find that your computer does not recognize the machine or operation is unstable, try connecting the USB cable to a
  • Sharp AM 900 | AM-900 Online Guide - Page 31
    in using the same user name as when you installed the software. 1. Disconnect the USB cable from your computer and the machine. 2. Open the Control Panel and select Add or Remove Programs (or Add/ Remove Programs). 3. Select SHARP AM-900 Series MFP Driver (or Sharpdesk) from the list, and click the
  • Sharp AM 900 | AM-900 Online Guide - Page 32
    the same version of Windows or a version that is older than the server. Configuring settings on the server Follow the appropriate procedure below for the server's operating system. Windows“ XP 1. Click the start button and click Printers and Faxes. 2. Right-click the SHARP AM-900 icon and select
  • Sharp AM 900 | AM-900 Online Guide - Page 33
    1. Installation Using the Machine as a Shared Printer on a Network 3. The following window will appear. Click Network Setup Wizard to run the wizard. 4. After running the wizard, the following window will appear. Select Share this printer. i If you would like to change the name, enter a new name (
  • Sharp AM 900 | AM-900 Online Guide - Page 34
    “ 2000 1. Click the Start button, point to Settings, and select Printers. 2. Right-click the SHARP AM-900 icon and select Sharing. 3. The following window will appear. Click Shared as. i If you would like to change the name, enter a new name (this must be 8 characters or less to allow sharing
  • Sharp AM 900 | AM-900 Online Guide - Page 35
    , see if File and Printer Sharing for Microsoft Networks appears in the list of installed network components. If it appears, click the OK button and go to Step 8. If it does not appear, continue from Step 3. 3. Click the Add button on the Configuration tab. 4. Select Service from the list of network
  • Sharp AM 900 | AM-900 Online Guide - Page 36
    on a Network 7. You will be prompted to restart your computer. Click OK to restart. 8. Click the Start button, point to Settings, and select Printers. 9. Right-click the SHARP AM-900 icon and select Sharing. 10. Select Shared As on the Sharing tab. i If you would like to change the name, enter a new
  • Sharp AM 900 | AM-900 Online Guide - Page 37
    system that each client is running. i Each client can only print to one AM-900 printer. It is not possible to install printer drivers for multiple AM-900 printers connected to the network (or directly to the client) and switch between those printers. Note: If the server is running Windows“ XP
  • Sharp AM 900 | AM-900 Online Guide - Page 38
    the Machine as a Shared Printer on a Network 4. Select Browse for a printer and click Next. 5. Select the AM-900 from the list of shared printers and click Next. 6. Select Yes if you would like to use the AM-900 as the default printer and click Next. 7. Click Finish. Windows“ 2000 1. Click the Start
  • Sharp AM 900 | AM-900 Online Guide - Page 39
    1. Installation Using the Machine as a Shared Printer on a Network 3. The following window will appear. Select Network printer and click Next. 4. Select Type the printer name, or click Next to browse for a printer and click Next. 5. Select the AM-900 from the list of shared printers and click Next.
  • Sharp AM 900 | AM-900 Online Guide - Page 40
    button, point to Settings, and select Printers. 2. Double-click the Add Printer icon. Click Next in the Add Printer Wizard. 3. The following window will appear. Select Network printer and click Next. 4. The following window will appear. Click Browse. 5. Select the AM-900 from the list of shared
  • Sharp AM 900 | AM-900 Online Guide - Page 41
    1. Installation Using the Machine as a Shared Printer on a Network 6. If the server is running Windows“ XP or 2000, the dialog box below will appear. Click Have Disk and click Next. If the server is running Windows“ Me, go to Step 10. 7. Click Browse. 8. Navigate to your CD-ROM drive and open the
  • Sharp AM 900 | AM-900 Online Guide - Page 42
    Using the Machine as a Shared Printer on a Network 9. The following window will appear. Click Next. 10. Select Yes if you would like to use the AM-900 as the default printer and click Next. 11. Select Yes if you would like the printer to print a test page. Click Finish. 40
  • Sharp AM 900 | AM-900 Online Guide - Page 43
    Entering Your Name and Fax Number 1. Installation Entering Your Name and Fax Number Before you can begin sending faxes, Press . ENTER FAX NUMBER 4 Enter your fax number by pressing the number keys (max. 20 digits). x To insert a space between digits, press . x To clear a mistake, press Z . 41
  • Sharp AM 900 | AM-900 Online Guide - Page 44
    as shown in the chart below. Up to 24 characters can be entered. Example: SHARP = 7777 44 2 777 A 7 SPACE = G = N = U = A = H = O = V = B = I = P = W = C = J = Q letter until the lower case letter appears. To enter one of the following symbols, press or repeatedly Note:
  • Sharp AM 900 | AM-900 Online Guide - Page 45
    Setting the Date and Time 1. Installation Setting the Date and Time The date and Press . 1: DATE&TIME SET 3 Press . The currently set date appears: DATE 01-01-2005 4 Enter a two-digit number for the month ("01" for January, "02" for February, "12" for December, etc.). Example: February DATE
  • Sharp AM 900 | AM-900 Online Guide - Page 46
    " to "31"). Example: the 5th DATE 02-05-2005 6 Enter the year (four digits). Example: 2005 The currently set time appears (example): TIME 12:00 AM 7 Enter a two-digit number for the hour ("01" to "12") and a two-digit number for the minute ("00" to "59"). Example: 9:25 TIME 09:25 AM 8 Press
  • Sharp AM 900 | AM-900 Online Guide - Page 47
    1. Installation Setting the Date and Time Daylight Saving Time If desired, you can set the clock to move forward and backward automatically at the beginning and
  • Sharp AM 900 | AM-900 Online Guide - Page 48
    General Machine Settings General Machine Settings Ringer Like a telephone, the machine will ring to alert you when a call comes in. To adjust the volume of the ringer or turn it off, follow the steps below. 1 Make sure that the date and time display of fax mode appears (if needed press FAX ) and
  • Sharp AM 900 | AM-900 Online Guide - Page 49
    1. Installation General Machine Settings Alarm volume The machine sounds a three-beep alarm to alert you when an error occurs during fax transmission or reception. To adjust
  • Sharp AM 900 | AM-900 Online Guide - Page 50
    General Machine Settings Auto clear After a copy job or fax job is completed, the machine will automatically return all temporary copy settings or all temporary fax settings to the default settings if 60 seconds elapses without any keys being pressed on the operation panel. If desired, you can
  • Sharp AM 900 | AM-900 Online Guide - Page 51
    1. Installation General Machine Settings Key tone off The machine normally sounds a beep (key tone) each time you press a key on the operation panel. If you wish
  • Sharp AM 900 | AM-900 Online Guide - Page 52
    General Machine Settings Selecting the display language If desired, you can change the language used in the display, reports and lists. 1 Press COPY (or SCAN ) and then MENU . 2 Press . Display: COMMON SETTING 1: ENGLISH 3 Press Z or A until the desired language appears and then press ENTER . x
  • Sharp AM 900 | AM-900 Online Guide - Page 53
    2. Copying 2. Copying Making a Copy To make a copy, you can place the original on the document glass or insert it into the auto document feeder. i The auto document feeder allows you to load up to 20 letter-size originals at once. 1 COPY Press to select copy mode. Display:  COPY 100%
  • Sharp AM 900 | AM-900 Online Guide - Page 54
    (the surface to be copied must lie flat on the glass). Using the auto document feeder: Adjust the document guide to the width of your original(s), and then insert the original face up into the feeder. x Up to 20 letter-size sheets can be inserted at once. x For detailed information on using
  • Sharp AM 900 | AM-900 Online Guide - Page 55
    settings. 4 When you are ready to make the copy, press . x If Duplex Scan is selected: After the stack of originals is fed through the auto document feeder, turn the entire stack over (do not change the order of the pages or remove any pages), insert it into the auto
  • Sharp AM 900 | AM-900 Online Guide - Page 56
    memory becomes full while multiple originals are being scanned using the auto document feeder, MEMORY IS FULL will appear in the display. i Press if 78% (legal to letter size), 64%, 50%, 25%, 400%, 200%, and 129% (letter to legal size). i After selecting one of the above preset percentages, you
  • Sharp AM 900 | AM-900 Online Guide - Page 57
    2. Copying Selecting Temporary Copy Settings Number of Copies If you wish to make more than one copy of the original (or of each original if you have loaded multiple originals in the auto document feeder), press the number keys to enter the number of copies. i The maximum number is 99. i To clear
  • Sharp AM 900 | AM-900 Online Guide - Page 58
    first time, you simply turn the stack over (do not change the order of the pages or remove any pages), insert it into the auto document feeder again, and press to scan the back side of the originals. The machine will automatically sort the copies into the correct order (front of 1st
  • Sharp AM 900 | AM-900 Online Guide - Page 59
    2. Copying Permanent Copy Settings Permanent Copy Settings The following copy settings remain in effect until they are changed. These settings do not revert to the default settings when the auto clear time elapses or when is pressed. Default copy quality setting The default quality setting (
  • Sharp AM 900 | AM-900 Online Guide - Page 60
    Permanent Copy Settings Copy resolution The copy resolution is initially set to 300 dpi. If you need a sharper image, follow the steps below to change the setting to 600 dpi. 1 Press MENU and then Z or A until the display at right appears. Display: COPY SETTING 2 Press . 1: 300 DPI 3 Select
  • Sharp AM 900 | AM-900 Online Guide - Page 61
    2. Copying Permanent Copy Settings Default copy contrast setting The default contrast setting (page 55) is medium (this is the setting that is used if you do not make a selection). If desired, you can change the default contrast to a higher or lower level. 1 Press MENU and then Z or A until the
  • Sharp AM 900 | AM-900 Online Guide - Page 62
    size: The maximum size and weight of documents that you can load in the document feeder depend on how many sheets you load. Up to 20 sheets at once: Size: Letter (8.5" x 11", 216 x 279 mm) Max. weight: 20 lbs. (80 g/m2) 1 sheet at a time (manual feeding): Max. size: 8.5" x 14" (216 x 356 mm
  • Sharp AM 900 | AM-900 Online Guide - Page 63
    the Auto Document Feeder Other restrictions i The scanner cannot recognize yellow, greenish yellow, or light blue ink. i Ink, glue, and correcting fluid on documents must be dry before they pass through the document feeder. i All clips, staples, and pins must be removed from documents before loading
  • Sharp AM 900 | AM-900 Online Guide - Page 64
    top edge of the document should enter the feeder first. x DOCUMENT READY will appear briefly in the display. x You can now continue with a copy, fax, or scan operation. Copying onto Envelopes and Cards To copy onto envelopes, cards, and other special sizes of paper, use the bypass tray on the side
  • Sharp AM 900 | AM-900 Online Guide - Page 65
    and then close the cover. Using the auto document feeder: Adjust the document guide to the width of your original, and then insert the original face up into the feeder. x Multiple originals (max. letter size) can be placed. 3 Adjust the document guides on the bypass tray to the width of the sheet or
  • Sharp AM 900 | AM-900 Online Guide - Page 66
    and Cards 4 Insert the sheet or envelope into the bypass tray as shown with the print side face down. x When needed and then press copying. to begin x If you placed multiple originals in the auto document feeder or set the number of copies to more than "1", copying will stop after the first
  • Sharp AM 900 | AM-900 Online Guide - Page 67
    number of the receiving machine, you can either directly enter the number with the number keys SPEED (Direct Keypad Dialing), or press and enter a two-digit Speed Dial number (Speed Dialing). i To use a Speed Dial number, you must first store the number in the machine as explained on page 70
  • Sharp AM 900 | AM-900 Online Guide - Page 68
    face down on the glass with the top edge against the document guide. x Make sure the center of the original is aligned with the center mark on the document guide, and then close the cover. Using the auto document feeder: Adjust the document guide to the width of your original(s), and then insert the
  • Sharp AM 900 | AM-900 Online Guide - Page 69
    settings. 4 Enter the number of the receiving machine using one of the following methods: x Direct Keypad Dialing: Press the number keys to enter the fax number. Note: If a pause is required between any of the digits to access a special REDIAL service or an outside line, press . The pause will
  • Sharp AM 900 | AM-900 Online Guide - Page 70
    one digit at a time, and then re-enter the correct digit(s). 6 Scanning of the original(s) will begin. x If you are using the auto document feeder once the machine is free. x If Duplex Scan is selected: After the stack of originals is fed through the auto document feeder, turn the entire stack
  • Sharp AM 900 | AM-900 Online Guide - Page 71
    display. i Press if you want to transmit the pages which have been stored up to that point in memory. If you are using the auto document feeder, the remaining pages will feed out without being scanned. After transmission, the memory will be cleared and you can transmit the remaining pages. You
  • Sharp AM 900 | AM-900 Online Guide - Page 72
    the full fax number in the machine and select a two-digit Speed Dial number for it. One hundred Speed Dial numbers are available (00 to 99). press Z . x If a pause is required between any of the digits to access a special service REDIAL or an outside line, press . The pause appears as a hyphen
  • Sharp AM 900 | AM-900 Online Guide - Page 73
    go directly to Step 8.) Example: SHARP = 7777 44 2 777 A one of the following symbols, press or repeatedly: Note: National characters of the selected display language will appear at the end of the symbol list. (For some languages, no national characters will appear.) 8 Press ENTER . SUPER G3
  • Sharp AM 900 | AM-900 Online Guide - Page 74
    the other machine also supports Super G3 mode. STORED #01 OK? NO: SET SPEED # YES: PRESS ENTER Note: "#01" is shown as an example above. 10 The display will show the next available Speed Dial number. If that number is acceptable, press ENTER . If not, enter the desired two-digit number and press
  • Sharp AM 900 | AM-900 Online Guide - Page 75
    to the number. x To move the cursor to the right, press A . When the cursor is over a digit that you wish to change, simply enter the new digit. The new digit will replace the old digit. To backspace and clear digits, press Z . x If you do not wish to change the number, go directly to Step 8. 73
  • Sharp AM 900 | AM-900 Online Guide - Page 76
    clear letters, press Z . x If you do not wish to change the name, go directly to Step 10. 10 Press ENTER . SUPER G3 1: ON, 2: OFF 11 Press press if you want the number to use Super G3 mode. Otherwise . 12 Return to Step 4 to edit or delete another number, or press repeatedly to exit. 74
  • Sharp AM 900 | AM-900 Online Guide - Page 77
    Fax Settings You can adjust one or more of the following temporary fax settings before pressing to begin transmission. Resolution The following resolution settings are available for faxing: STANDARD FINE SUPER FINE HALF TONE Use STANDARD for ordinary documents. This setting gives you the
  • Sharp AM 900 | AM-900 Online Guide - Page 78
    order of the pages or remove any pages), insert it into the auto document feeder again, and press to scan the back side of the originals. The machine the receiving machine is responding correctly. FAX To select Line Monitor, press one or more times until MONITOR ON appears in the display. i The
  • Sharp AM 900 | AM-900 Online Guide - Page 79
    3. Sending Faxes Other Fax Transmission Settings Other Fax Transmission Settings Checking and canceling stored fax jobs Follow the steps below to check the fax jobs that are waiting in memory for transmission. You can also use this procedure to cancel a stored fax job. 1 Make sure that the date
  • Sharp AM 900 | AM-900 Online Guide - Page 80
    MENU . Display: FAX SETTING 2 Press . 1: AUTO RECALL 3 Press 3 times. 4 Press the numeric keys to enter the desired interval in minutes (any 2-digit number from 01 to 15). Example: 1 minute ENTER (01 - 15) 05 RECALL INTERVAL The display briefly shows your selection, then: 2: RECALL TIMES
  • Sharp AM 900 | AM-900 Online Guide - Page 81
    Press . 1: AUTO RECALL 3 Press twice. 1: RECALL INTERV. 4 Press . 5 Press the numeric keys to enter the desired number of recall attempts (any 2-digit number from 00 to 14). Example: 5 attempts ENTER (00 - 14) 02 RECALL TIMES The display briefly shows your selection, then: 1: RECALL INTERV
  • Sharp AM 900 | AM-900 Online Guide - Page 82
    attempt to complete the transmission. Retransmission will begin from the page which was being transmitted when the error occurred. The machine will make one attempt at retransmission after an interval of two minutes. i To cancel a job that is waiting for automatic redialing, follow the procedure in
  • Sharp AM 900 | AM-900 Online Guide - Page 83
    Other Fax Transmission Settings 3. Sending Faxes 6 Press the numeric keys to enter the desired interval in minutes (any 2-digit number from 01 to 15). Example: 1 minute 7 Press repeatedly to exit. The display briefly shows your selection, then: 2: RECALL TIMES Recall times for automatic
  • Sharp AM 900 | AM-900 Online Guide - Page 84
    Default resolution for faxing The default resolution for faxing is initially set to STANDARD. If desired, you can change the default resolution to FINE or SUPER FINE. 1 Make sure that the date and time display of fax mode appears (if needed press FAX ) and then press MENU . Display: FAX SETTING
  • Sharp AM 900 | AM-900 Online Guide - Page 85
    Using an Extension Phone to Send a Fax Default Line Monitor setting The default setting for Line Monitor (listening to the line and fax tones through the speaker during a fax transmission) is initially MONITOR OFF. If desired, you can change the default setting to MONITOR ON. 1 Make sure that the
  • Sharp AM 900 | AM-900 Online Guide - Page 86
    a Fax 2 Place the original on the document glass or in the auto document feeder. x If the document glass is used, only one page can be transmitted. x If needed, fax tone, press on the machine. MANUAL MODE 1:SEND, 2:RECEIVE 6 Press to select SEND. Replace the extension phone. x Transmission
  • Sharp AM 900 | AM-900 Online Guide - Page 87
    glass or in the auto document feeder. x If needed, select temporary fax settings such as the resolution and contrast. 3 BROADCAST Press . BROADCAST MODE ENTER SPEED # OR SELECT BY , 4 Select a destination using one of the methods below. x Enter the 2-digit Speed Dial number of the destination
  • Sharp AM 900 | AM-900 Online Guide - Page 88
    1 Make sure that the date and time display of fax mode appears (if needed FAX press ). 2 Place the original on the document glass or in the auto document feeder. x If needed, select temporary fax settings such as the resolution and contrast. 3 Press A once or twice to display Group 1 or Group
  • Sharp AM 900 | AM-900 Online Guide - Page 89
    in the display. This is the number of the Group you are storing. ENTER SPEED # OR SELECT BY , 5 Select a destination using one of the methods below. x Enter the 2-digit Speed Dial number of the destination. x Press Z or A until the name of the destination appears in the display (if no name was
  • Sharp AM 900 | AM-900 Online Guide - Page 90
    Broadcasting (Sending a Fax to Multiple Destinations) 7 Repeat Steps 5 and 6 for each of the other destinations that you want to include in the Group (maximum of 100). x To check your selected destinations, press MENU to scroll through them. To delete a destination, scroll to the destination and
  • Sharp AM 900 | AM-900 Online Guide - Page 91
    , store the job again. 1 Make sure that the date and time display of fax mode appears (if needed FAX press ). 2 Place the original on the document glass or in the auto document feeder. 3 Press MENU . Display: FAX SETTING 4 Press . 1: AUTO RECALL 5 Press . 1: SET, 2: CLEAR 89
  • Sharp AM 900 | AM-900 Online Guide - Page 92
    Timer Transmission 6 Press to select SET. x Note which Timer number (Timer 1, 2, 3, or 4) appears in the display. This is the number of the Timer job you are storing. The first available Timer number appears: TIMER NUMBER=1 ENTER TIME 7 Enter the time at which you want the fax to be sent.
  • Sharp AM 900 | AM-900 Online Guide - Page 93
    Timer Transmission 11 Select a destination using one of the methods below: x Press SPEED , enter the 2-digit Speed Dial number of the destination, and press ENTER . x Press Z or A until the name of the destination appears in the display (if no name was
  • Sharp AM 900 | AM-900 Online Guide - Page 94
    Timer Transmission Canceling a timer job If you need to cancel a timer job before it is performed, follow the steps below. i You will need to know the timer number assigned to the job in order to cancel it. If you don't remember the number (it appears in the display when you store the job), print
  • Sharp AM 900 | AM-900 Online Guide - Page 95
    faxes: FAX ONLY mode: Select this mode when you only want to receive faxes on your line. The machine will automatically answer all calls on one ring and receive incoming faxes. ("FAX" will appear in the fax mode display.) EXT. TEL mode: Select this mode when you have connected an extension
  • Sharp AM 900 | AM-900 Online Guide - Page 96
    Using FAX ONLY Mode Using FAX ONLY Mode When the reception mode is set to FAX ONLY, the machine will automatically answer all calls on one ring and receive incoming faxes. i The number of rings on which the machine answers can be changed as explained below. i When the reception mode is
  • Sharp AM 900 | AM-900 Online Guide - Page 97
    , press on the machine. x If the other party first speaks with you, press after speaking. (Press before the sender presses their Start key.) MANUAL MODE 1:SEND, 2:RECEIVE 3 Press to select RECEIVE. Replace the extension phone. x RECEIVING will appear in the display and reception will begin
  • Sharp AM 900 | AM-900 Online Guide - Page 98
    middle of a line. i Automatic reduction may not be possible if the received document is too large, contains too many fine graphics or images, or is sent at high resolution. In this case, the remainder of the document will be printed on a second page. 1 Make sure that the date and
  • Sharp AM 900 | AM-900 Online Guide - Page 99
    such as when the machine runs out of paper, the toner cartridge needs replacement, or the paper jams, incoming faxes will be tray). When you have received a fax in memory, FAX RX IN MEMORY will appear in the display, alternating with a message that indicates the problem. When you resolve the problem
  • Sharp AM 900 | AM-900 Online Guide - Page 100
    an additional second number to your regular single line. The second number rings differently from your normal number. If you subscribe to a distinctive ring service, you can set the machine to automatically answer when your second number is called. This allows you to use the second number as an
  • Sharp AM 900 | AM-900 Online Guide - Page 101
    Distinctive Ring (Requires Subscription to Service) 4 Press a number from 1 to 3 (1 to 5 in Canada function, press 7. : PATTERN 1 Two short rings : PATTERN 2 One short, one long, and one short ring : PATTERN 3 Two short rings and one long ring : PATTERN 4 Three very short rings (Canada only)
  • Sharp AM 900 | AM-900 Online Guide - Page 102
    another fax machine and have it send a document (previously loaded in the machine's feeder or stored in memory) to your machine that you want to poll using one of the following methods: x Enter the full fax number and press . x Press SPEED , enter a 2-digit Speed Dial number, and press .
  • Sharp AM 900 | AM-900 Online Guide - Page 103
    will remain in memory until you clear it as explained in the following section, Clearing a memory polling document. 1 Place the original on the document glass or in the auto document feeder. 2 Make sure that the date and time display of fax mode appears (if needed press FAX ) and then press
  • Sharp AM 900 | AM-900 Online Guide - Page 104
    (see page 93). (When the polling fax machine calls, the machine must answer automatically in order to transmit the document.) Clearing a memory polling document To clear a memory polling document from memory, follow these steps: 1 Make sure that the date and time display of fax mode appears (if
  • Sharp AM 900 | AM-900 Online Guide - Page 105
    printer driver must be installed on your computer (see page 23). 1. When you are ready to print a document from Printer in the Print dialog box (the name of the button varies depending on the application). The SHARP AM-900 Printing Preferences ("SHARP AM-900 Properties" in some versions of Windows
  • Sharp AM 900 | AM-900 Online Guide - Page 106
    from the Printers and Faxes folder (the Printers folder in Windows“ Me/2000) as explained below: Windows“ XP: Click the start button, click Control Panel, click Printers and Other Hardware, and then click Printers and Faxes. In the Printers and Faxes window, click on the SHARP AM-900 icon and
  • Sharp AM 900 | AM-900 Online Guide - Page 107
    Size and Paper Source. When the Paper Source is set to Tray, the Paper Size can be set to Letter or Legal. paper, select 2 Pages per Sheet. x For a normal document, set the Orientation to Portrait. If the document is oriented so that the width is longer than the height printer driver settings. 105
  • Sharp AM 900 | AM-900 Online Guide - Page 108
    Selecting Print Settings Advanced tab The Advanced tab is used to specify how the printed image is scaled to the paper. Normally Match Page Size is selected so that the image size matches the paper size selected on the Page Setup tab (the image is not reduced). 106
  • Sharp AM 900 | AM-900 Online Guide - Page 109
    Selecting Print Settings x If you wish to scale the image to a smaller size, select Auto Scaling. The paper size setting on the Page Setup tab will appear in Current Page Size. Select the size to which you wish to scale the image in Output Size. The amount of the reduction will be shown in the page
  • Sharp AM 900 | AM-900 Online Guide - Page 110
    size in the Page Setup tab of the SHARP AM-900 Printing Preferences (or "Properties") before printing. (Select Properties, Setup, or Printer from the Print dialog box to open the SHARP AM-900 Printing Preferences.) 1 Adjust the document guides on the bypass tray to the width of the sheet or envelope
  • Sharp AM 900 | AM-900 Online Guide - Page 111
    to open the Print dialog box. Click "Properties", "Setup", or "Printer" (the name of the button varies depending on the application) in the dialog box to open the SHARP AM-900 Printing Preferences (or "Properties"). Set the "Paper Source" to "Bypass Tray" on the "Page Setup" tab and then select the
  • Sharp AM 900 | AM-900 Online Guide - Page 112
    the machine must be connected to your computer with a USB cable, and the scanner driver and utility software (Sharpdesk) must be installed on your computer (see page 23). i Depending on your system and the application being used, it may take considerable time for an image scanned at high resolution
  • Sharp AM 900 | AM-900 Online Guide - Page 113
    TWAIN Application Using the auto document feeder: Adjust the document guide to the width of your original(s), and then insert the originals face up into the feeder. x Up to 20 letter-size sheets can be inserted at once. Note that some applications may only allow you to scan one page at a time. x For
  • Sharp AM 900 | AM-900 Online Guide - Page 114
    MFP TWAIN I" and click the Select button. Note: The selection WIA-SHARP AM-900 is for WIA applications and is explained in the following section. 5 Click the File menu and select "Acquire Image". 6 The TWAIN scanner driver window will appear. Select settings as desired (see the next page) and then
  • Sharp AM 900 | AM-900 Online Guide - Page 115
    Scanning From a TWAIN Application x If you are using the auto document feeder, select Use Automatic Document Feeder. x If you wish to use the standard preset scanning settings, click Photo or Document as appropriate for the original in the Standard Preset field. x The Advanced Controls can be
  • Sharp AM 900 | AM-900 Online Guide - Page 116
    a WIA Application (Windows XP/Me only) Scanning From a WIA Application (Windows XP/Me only) If you are using Windows“ XP or Windows“ Me, you can scan a document into Paint“ or any other WIA-compliant application. i The auto document feeder cannot be used to scan a document into a WIA application
  • Sharp AM 900 | AM-900 Online Guide - Page 117
    From a WIA Application (Windows XP/Me only) 3 Click the File menu and select "From Scanner or Camera". x The File menu of Paint“ is shown below. 4 If you have WIA drivers for other devices installed on your system, the "Select Device" window will appear. Select "WIA-SHARP AM-900" and click the OK
  • Sharp AM 900 | AM-900 Online Guide - Page 118
    Scanning From a WIA Application (Windows XP/Me only) 5 The following window will appear. Select the desired scan settings and then click the Scan button to begin scanning. x To view a preview of the scanned image using the
  • Sharp AM 900 | AM-900 Online Guide - Page 119
    XP/Me only) Scanning From the Scanner Wizard (Windows XP/Me only) If you are using Windows“ XP/Me, you can also scan from the Scanner and Camera Wizard. Place the original on the document glass (the auto document feeder cannot be used). Click the start button, click Control Panel, click Printers
  • Sharp AM 900 | AM-900 Online Guide - Page 120
    one installed. Linking programs to scan menus Follow the appropriate procedure below for your operating system to link programs to scan menus. Windows“ XP 1. Click the start button, click Control Panel, click Printers and Other Hardware, and then click Scanners and Cameras. 2. Right-click the SHARP
  • Sharp AM 900 | AM-900 Online Guide - Page 121
    Scanning From the Operation Panel 3. The SHARP AM-900 Properties appear. Click on the Events tab. 4. Select SC1 (scan menu SC1) from the Select an event list. 119 7. Scanning
  • Sharp AM 900 | AM-900 Online Guide - Page 122
    and then select the program that you wish to link to scan menu SC1 from the list of programs. i Microsoft Scanner and Camera Wizard is selected as an example in the window below. 6. Click the Apply button. 7. Repeat Steps 4 through 6 as needed for any of the other scan menus (SC2 to SC6
  • Sharp AM 900 | AM-900 Online Guide - Page 123
    the Properties button. 4. Click the Events tab in the SHARP AM-900 Properties. 5. Select SC1 from the Scanner events list. 6. In Send to this application, select the program that you wish to link to scan menu SC1 (make sure only one program is selected). 7. Click the Apply button. 8. Repeat Steps
  • Sharp AM 900 | AM-900 Online Guide - Page 124
    From the Operation Panel Windows“ Me 1. Click the Start button, point to Settings, select Control Panel, and then double-click Scanners and Cameras. i If Scanners and Cameras does not appear in the Control Panel, click view all Control Panel options. 2. Right-click the SHARP AM-900 icon and select
  • Sharp AM 900 | AM-900 Online Guide - Page 125
    computer. Select the program that you wish to link to scan menu from the list of programs. In addition, to stop the window from appearing each time you use that scan menu, select Always use this program for this action. i Microsoft Scanner and Camera Wizard is selected as an example in the
  • Sharp AM 900 | AM-900 Online Guide - Page 126
    scanned image. Using the auto document feeder: Adjust the document guide to the width of your original(s), and then insert the originals face up into the feeder. x Up to 20 letter-size sheets can be inserted at once. Note that some applications may only allow you to scan one page at a time. x For
  • Sharp AM 900 | AM-900 Online Guide - Page 127
    Scanning From the Operation Panel 3 Press Z or A until the desired scan menu appears in the display. Example: Press A once for SC2: SCAN : SC2 4 Press . x The program linked to the selected scan menu starts on your computer. Respond appropriately as prompted by the program to complete the scan
  • Sharp AM 900 | AM-900 Online Guide - Page 128
    . 4 Press ENTER once. Activity List This list shows information on your most recent 30 fax transactions. The report is divided into two parts: the SEND REPORT, which shows information on fax transmissions, and the RECEIVE REPORT, which shows information on fax receptions. i All information is
  • Sharp AM 900 | AM-900 Online Guide - Page 129
    of every page you transmit (HEADER PRINT). Timer List This shows the timer transmission jobs that are currently stored. Help List This list provides a brief guide to the operation of the machine. To print this SCAN FAX list, press and simultaneously. 127
  • Sharp AM 900 | AM-900 Online Guide - Page 130
    taken for transmission/reception. Number of pages transmitted/received. (One of the following notes will appear under NOTE in the The transaction was cancelled because the STOP key was pressed, no document was in the feeder, or the other machine requested transmission using a function which your
  • Sharp AM 900 | AM-900 Online Guide - Page 131
    8. Printing Lists Printing Lists Transaction Report print condition You can change the condition under which a Transaction Report is printed out. Follow the steps below. 1 Make sure that the date and time display of fax mode appears (if needed press FAX ) and then press MENU Display: FAX SETTING
  • Sharp AM 900 | AM-900 Online Guide - Page 132
    Printing Lists Auto print-out of Activity List You can set the Activity List to print automatically whenever information on 30 fax transactions has accumulated. (The Activity List can still be printed on demand at any time.) Follow these steps: 1 Make sure that the date and time display of fax
  • Sharp AM 900 | AM-900 Online Guide - Page 133
    regularly as explained below. Cleaning the scanning glass in the auto document feeder 1 Squeeze the cover release ➊ and open the auto document feeder cover. Open 1 the document glass cover. 2 Wipe the parts indicated in white below (scanning glass, rollers, and white backplate) with a clean
  • Sharp AM 900 | AM-900 Online Guide - Page 134
    Maintenance 3 Close the auto document feeder cover, pressing down on both sides to make sure it clicks into place. Press down on the marks Cleaning the document glass Open the document glass cover and clean the document glass by wiping it with a soft, dry cloth (be sure not to use a cloth that will
  • Sharp AM 900 | AM-900 Online Guide - Page 135
    the side cover release to open the side cover, and then clean the rollers indicated below with a clean cloth. Cleaning the housing Wipe the external parts and surface of the machine with a dry cloth. Caution! i Do not use benzene or thinner. These solvents may damage or discolor the machine. 133
  • Sharp AM 900 | AM-900 Online Guide - Page 136
    1 2 2 Press the center roller with your finger to make it rotate a half turn back into the machine. 3 Remove the output tray and then remove the paper from the paper tray. Wipe the side of the center roller that is visible in the paper inlet with a damp cloth. x When finished, replace the paper
  • Sharp AM 900 | AM-900 Online Guide - Page 137
    Once a fax is received, it will be held in memory and printing will no longer be possible. Replace the toner cartridge with the following cartridge: Sharp AM-90ND toner cartridge 1 Press the side cover release ➊, open the side cover ➋, and then open the front cover ➌. 1 3 2 x Caution! The fusing
  • Sharp AM 900 | AM-900 Online Guide - Page 138
    Maintenance 3 Continue from Step 4 on page 17 to install the new toner cartridge. Replacing the Drum Cartridge Viewing the total number of pages printed To maintain excellent printing quality, we recommend that you replace the drum cartridge after 20,000 pages have been printed. Follow these steps
  • Sharp AM 900 | AM-900 Online Guide - Page 139
    cartridge: Sharp AM-90DR drum cartridge 1 Press the side cover release ➊, open the side cover ➋, and then open the front cover ➌. 1 3 2 x Caution! The fusing unit inside the print compartment becomes very hot during operation. Do not touch the inside of the print compartment except as instructed
  • Sharp AM 900 | AM-900 Online Guide - Page 140
    3 Grasp the drum cartridge handle and gently pull the old cartridge out of the machine. 4 Remove the new drum cartridge from its packaging. 5 Insert the drum cartridge into the print compartment, sliding it along the guides. x Do not touch or allow other objects to contact the drum (the green
  • Sharp AM 900 | AM-900 Online Guide - Page 141
    10.. Troubleshooting 10. Troubleshooting Problems and Solutions If you have any problems with the machine, first refer to the following troubleshooting guide. If you cannot solve the problem, call Sharp's Customer Assistance Center at 1-877-794-8675 (U.S.A. only). Line error Problem Solution
  • Sharp AM 900 | AM-900 Online Guide - Page 142
    problems Problem not the TEL. SET jack. • If the receiving machine is in manual mode with no attendant, reception will not be possible. • Check document for transmission is placed face down if you are using the document glass, or face up if you are using the auto document feeder. 140
  • Sharp AM 900 | AM-900 Online Guide - Page 143
    10. Troubleshooting A distorted image is • Noise on the telephone line may cause distortion. Try received at the other end. sending the document again. • Make a copy of the document on your machine. If the copy is also distorted, your machine may need service. Fax reception problems Problem
  • Sharp AM 900 | AM-900 Online Guide - Page 144
    problems Problem Solution The quality of copies is poor and/or dark vertical lines appear when the document feeder document feeder, make sure the original is placed face up in the feeder. • If you are using the document . • The drum cartridge may be damaged. Replace the drum cartridge. A copy is
  • Sharp AM 900 | AM-900 Online Guide - Page 145
    10. Troubleshooting Problems and Solutions General problems Problem Solution Nothing appears in the display. • make sure that the scanner lock has been released (see page 12). Characters or parts of the image are missing from printed output. • Remove the drum cartridge as explained on page
  • Sharp AM 900 | AM-900 Online Guide - Page 146
    scanner lock has been released (see page 12) and then unplug the power cord, wait at least 5 seconds, and plug it back in. COVER OPEN One failure occurs. DOCUMENT JAMMED The original document is jammed in the auto document feeder. See the following section, Clearing Paper Jams. Document jams will
  • Sharp AM 900 | AM-900 Online Guide - Page 147
    10. Troubleshooting DRUM LIFE OVER FAX RX IN MEMORY GRP. SPACE FULL LINE ERROR MEMORY IS FULL NO # STORED OFF HOOK OUTPUT TRAY OFF PAPER JAMMED PAPER MISMATCHED This appears when the drum cartridge needs replacement. A fax has been received in memory because the toner cartridge needs replacement
  • Sharp AM 900 | AM-900 Online Guide - Page 148
    ; a paper size appears in "XXXX") Paper must be inserted in the bypass tray for a print job or copy job that requires use of the bypass tray. Insert the indicated size of paper in the tray. TONER EMPTY The toner cartridge must be replaced. Printing will be possible (although the output will be
  • Sharp AM 900 | AM-900 Online Guide - Page 149
    10. Troubleshooting Clearing Paper Jams Clearing Paper Jams Clearing a jammed document If the original document doesn't feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing . If the document doesn't feed out, open the auto document feeder
  • Sharp AM 900 | AM-900 Online Guide - Page 150
    Clearing Paper Jams 3 Close the auto document feeder cover, pressing down on both sides to make sure it clicks into place. Press down on the marks 148
  • Sharp AM 900 | AM-900 Online Guide - Page 151
    printing paper 1 Press the side cover release ➊ and then open the side cover ➋. 1 10. Troubleshooting 2 Push the two heater roller release levers down to release the heater roller. x Caution! The care not to touch or allow other objects to contact the drum (the green cylinder). This may damage the
  • Sharp AM 900 | AM-900 Online Guide - Page 152
    pulled out directly, open the front cover ➊ and rotate the white knob ➋ in the direction shown to feed the jammed page out into the output tray. 5 After the jammed page has been removed, push the two heater roller release levers back up. 2 1 6 Close the front cover ➊ (if you opened it) and
  • Sharp AM 900 | AM-900 Online Guide - Page 153
    located nearest you. When ordering a part, use the part order number shown below. Setup Guide TCADH3738XHZZ Output tray LPCTP3344XHSA Telephone line cord QCNWG370BXHZZ CD-ROM UDSKA2050XHZB Document feeder tray PHOP-2121XHSA Part distribution centers Tritronics, Inc. 1306 Continental
  • Sharp AM 900 | AM-900 Online Guide - Page 154
    comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. This equipment
  • Sharp AM 900 | AM-900 Online Guide - Page 155
    Company Identification Product Name : Toner Cartridge of AM-900, AM-700, AM-90ND, DUNT-29LDXH01 Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, 4. First-Aid Measures Ingestion: Wash out mouth with water. Drink one or two glasses of water. If symptoms occur, get medical attention.
  • Sharp AM 900 | AM-900 Online Guide - Page 156
    S H A R P Date Revised : Date Issued :Sep. 16, 2004 MATERIAL SAFETY DATA SHEET (2/4) MSDS No. B-1021 Section 5. Fire-Fighting Measures Suitable Extinguishing Media: CO2, water spray, foam and dry chemical Extinguishing Media to Avoid: Full water jet Fire and Explosion Hazards: If dispersed in air,
  • Sharp AM 900 | AM-900 Online Guide - Page 157
    a two-year inhalation study of chronic toxicity and carcinogenicity using a typical toner in rats, there were no lung changes at all in the lowest development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung
  • Sharp AM 900 | AM-900 Online Guide - Page 158
    ): Health: 1 Flammability: 1 Reactivity: 0 Recommended Uses: Toner for Electrophotographic Equipment Explanation of term : IARC 2B means " the manufacturer. This information is supplied to us by the manufacturer and Sharp offers no warranties as to its accuracy and accepts no responsibilities for
  • Sharp AM 900 | AM-900 Online Guide - Page 159
    signals, 146 Auto clear, 48 Auto document feeder Document restrictions, 61 Document sizes, 60 Loading document, 61 Automatic redialing Line busy, 78 Document glass, cleaning, 132 Document guides, 61 Document guides, bypass tray, 63 Document, maximum scanning size, 60 Drum cartridge Installing,
  • Sharp AM 900 | AM-900 Online Guide - Page 160
    of rings in FAX ONLY reception mode, 94 O Ordering parts, 151 P Paper feed roller, cleaning, 134 Paper jams Software, installing, 23 Speed Dialing, 67 T TEL. LINE jack, 14 TEL. SET jack, 15 Telephone line cord, 14 Telephone Number List, 127 Time, setting, 43 Timer List, 127 Toner cartridge Installing
  • Sharp AM 900 | AM-900 Online Guide - Page 161
    SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163 SHARP ELECTRONICS OF CANADA LTD SHARP ÉLECTRONIQUE DU CANADA LTÉE 335 Britannia Road East, Mississauga, Ontario L4Z 1W9 http://www.sharp.ca SHARP CORPORATION Ver 1.1
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
DIGITAL MULTIFUNCTIONAL SYSTEM
ONLINE GUIDE
MODEL
AM-900
1. Installation
2. Copying
3. Sending Faxes
4. Receiving Faxes
5. Special Fax Functions
6. Printing
7. Scanning
8. Printing Lists
9. Maintenance
10. Troubleshooting