Sony EVIHD7V Product Manual (HD Color Video Camera) - Page 28

Command List EVI-HD7V/HD3V Command List (3/3) Command Set Command Command Packet Comments VideoSystem SET 5) 8x 01 06 35 00 0p FF p Video format HD7V HD3V Output connetor 0 1920×1080p/59.94 Yes 1 1920×1080p/29.97 Yes No 59.94 Hz DVI-D system No 2 1920×1080i/59.94 Yes No 3 1280×720p/59.94 Yes Yes 4 1280×720p/29.97 Yes Yes 5 640×480p/59.94 Yes Yes (Letter Box) 8 1920×1080p/50 9 1920×1080p/25 Yes No 50 Hz system Yes No A 1920×1080i/50 B 1280×720p/50 Yes No Yes Yes C 1280×720p/25 Yes Yes IR_Receive On 8x 01 06 08 02 FF IR(remote commander) receive ON/OFF Off 8x 01 06 08 03 FF On/Off 8x 01 06 08 10 FF IR_ReceiveReturn On 8x 01 7D 01 03 00 00 FF IR (remote commander) receive message via the VISCA communication ON/OFF Off 8x 01 7D 01 13 00 00 FF For contents of messages, see page 30. Information Display On 8x 01 7E 01 18 02 FF ON/OFF of the Operation status display of One Push Off 8x 01 7E 01 18 03 FF Trigger of CAM_Memory and CAM_WB Color system RGB 8x 01 7E 01 03 00 00 FF Color-reproduction format setting for VIDEO signals YPbPr 8x 01 7E 01 03 00 01 FF Pan-tiltDrive Up 3) 8x 01 06 01 VV WW 03 01 FF VV: Pan speed 0 x01 (low speed) to 0 x18 (high speed) Down 3) 8x 01 06 01 VV WW 03 02 FF WW: Tilt Speed 0 x 01 (low speed) to 0 x14 (high speed) Left 3) 8x 01 06 01 VV WW 01 03 FF YYYY: Pan Position FA60 to 05A0 (center 0000) Right 3) 8x 01 06 01 VV WW 02 03 FF ZZZZ: Tilt Position FE98 to 0168 (center 0000) UpLeft 3) 8x 01 06 01 VV WW 01 01 FF UpRight 3) 8x 01 06 01 VV WW 02 01 FF See page 37. DownLeft 3) 8x 01 06 01 VV WW 01 02 FF DownRight 3) 8x 01 06 01 VV WW 02 02 FF Stop 3) 8x 01 06 01 VV WW 03 03 FF AbsolutePosition 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF RelativePosition 8x 01 06 03 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF Home 8x 01 06 04 FF Reset 8x 01 06 05 FF Pan-tiltLimitSet LimitSet 8x 01 06 07 00 0W W: 1 UpRight 0: DownLeft 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF YYYY: Pan Limit Position FA60 to 05A0 (center 0000) LimitClear 8x 01 06 07 01 0W 07 0F 0F 0F 07 0F 0F 0F FF ZZZZ: Tilt Position FE98~0168 (center 0000) 1) After an ACK to a One Push White Balance Trigger is sent until the operation is completed, "Not Executable" is sent as a reply when any other commands are received. 2) Bright can be set only in Full Auto mode or Shutter Priority mode. 3) When the menu is displayed, this operation is ignored. 4) When other commands are received after a Completion notification for the Recall command is sent, "Command not executable" may be returned for a maximum of 240 msec due to internal processing. In this case, please transmit the command again. 5) Can be configured when the SYSTEM SELECT switch at the rear of the camera is set to position 7. Use one of the following methods to apply the settings. • Turn off DC power, and turn it on again. • Turn off power using the IR remote commander, and turn it on again. • Send CAM_Power On and Off commands. 28