Sony MHC-NX1 Service Manual - Page 53

CHASSIS MOLD, STOCKER, SLIDER SELECTION, GEARS, INSTALLATION, Note: Rotating the pulley LD

Page 53 highlights

CHASSIS (MOLD B) SECTION, STOCKER SECTION AND SLIDER (SELECTION) Note: In mounting the parts, refer to page 11 and 12. 6 two screws (PTPWH M2.6) 5 stocker section 7 slider (selection) 8 washer pulley (LD) 9 compression spring 1 three screws (BVTP M2.6) 4 two step screws GEARS INSTALLATION 3 gear (gear B) portion A 4 two step screws 2 chassis (mold B) section Note: Rotating the pulley (LD), shift the slider (selection) to the left. 3 gear (eject) Adjust the gear (gear B) with the portion A as shown. 1 Slide the slider (U/D) fully in the arrow direction. 2 gear (U/D slider) slider (U/D) gear Adjust the gear so that it meshes with the bottom tooth of slider (U/D)gear, as shown. 10 4 gear (gear A) gear (gear B) linearly Adjust so as to be aligned with gear (B) linearly,as shown.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97

10
CHASSIS (MOLD
B)
SECTION,
STOCKER
SECTION
AND
SLIDER (SELECTION)
Note:
In mounting the parts, refer to page 11 and 12.
GEARS
INSTALLATION
5
stocker
section
4
two step
screws
4
two step screws
3
gear (eject)
2
chassis (mold B) section
Note: Rotating the pulley (LD),
shift the slider (selection)
to the left.
9
compression
spring
7
slider (selection)
8
washer
6
two screws
(PTPWH M2.6)
1
three screws
(BVTP M2.6)
pulley (LD)
1
Slide the slider (U/D)
fully in the arrow
direction.
3
gear (gear B)
2
gear (U/D slider)
4
gear (gear A)
Adjust the gear (gear B) with the
portion A as shown.
Adjust the gear so that it meshes with
the bottom tooth of slider (U/D)gear,
as shown.
portion A
slider (U/D) gear
linearly
gear
(gear B)
Adjust so as to be aligned with
gear (B) linearly,as shown.