Sony MHC-NX1 Service Manual - Page 62

DIAGRAMS, PRINTED, WIRING, BOARDS, SCHEMATIC, In addition to

Get Sony MHC-NX1 PDF manuals and user guides View all Sony MHC-NX1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

SECTION 7 DIAGRAMS 7-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • x : parts mounted on the conductor side. • b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. • Indication of transistor. Q BCE Q These are omitted. BCE These are omitted. C Q These are omitted. BE Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • 5 : fusible resistor. • C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. • U : B+ Line. • V : B- Line. • H : adjustment for repair. • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. E : TAPE PLAYBACK (DECK A) d : TAPE PLAYBACK (DECK B) G : RECORD J : CD PLAY (ANALOG OUT) c : CD PLAY (DIGITAL OUT) • Abbreviation AUS : Australian model CND : Canadian model JE : Tourist model KR : Korean model MY : Malaysia model SP : Singapore model TH : Thai model • Circuit Boards Location SENSOR 2 board SENSOR board CLAMP MOTOR board BD board PANEL board IN SW board INT/COUNT SW board LEAF SW board PANEL TC-B board PANEL TC-A board OUT SW board MAIN board CONNECTOR board LOAD MOTOR board AUDIO board 19 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
19
19
SECTION
7
DIAGRAMS
7-1.
NOTE
FOR
PRINTED
WIRING
BOARDS
AND
SCHEMATIC
DIAGRAMS
(In addition to this, the necessary note is printed in each block)
Note on Schematic Diagram:
•
All capacitors are in μF unless otherwise noted.
pF: μμF
50 WV or less are not indicated except for electrolytics
and tantalums.
•
All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
f
: internal component.
•
5
: fusible resistor.
•
C
: panel designation.
•
U
: B+ Line.
•
V
: B– Line.
•
H
: adjustment for repair.
•
Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
•
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
•
Circled numbers refer to waveforms.
•
Signal path.
E
: TAPE PLAYBACK (DECK A)
d
: TAPE PLAYBACK (DECK B)
G
: RECORD
J
: CD PLAY (ANALOG OUT)
c
: CD PLAY (DIGITAL OUT)
• Abbreviation
AUS
: Australian model
CND
: Canadian model
JE
: Tourist model
KR
: Korean model
MY
: Malaysia model
SP
: Singapore model
TH
: Thai model
Note:
The components identi-
fied by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro
spécifié.
Note on Printed Wiring Board:
•
X
: parts extracted from the component side.
•
Y
: parts extracted from the conductor side.
•
x
: parts mounted on the conductor side.
•
b
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
Parts on the pattern face side seen from
(Side B)
the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(Side A)
the parts face are indicated.
•
Indication of transistor.
C
B
These are omitted.
E
Q
B
These are omitted.
C
E
Q
B
These are omitted.
C
E
Q
•
Circuit Boards Location
CLAMP MOTOR board
BD board
IN SW board
INT/COUNT SW board
MAIN board
CONNECTOR board
LOAD MOTOR board
AUDIO board
OUT SW board
PANEL TC-A board
PANEL TC-B board
LEAF SW board
PANEL board
SENSOR board
SENSOR 2 board