Sony PDX10 Operating Instructions - Page 31

When you unplug the microphone plug, When detaching the XLR adaptor

Page 31 highlights

Recording - Basics Recording a picture Note If you use equipment other than a 48-V microphone with the +48V switch set to ON, a malfunction of the equipment may occur. When you connect equipment other than a 48-V microphone, set it to OFF. When the wind is blowing hard Set INPUT1 of the LOW CUT switch to ON when the audio is input via the INPUT1 connector. Set INPUT2 to ON when the audio is input via the INPUT2 connector. The sound of wind is reduced. We recommend that you set MIC NR to OFF in the menu settings in the following cases: - When you use the external microphone at a distance from the camcorder. - When the REC CH SELECT switch is set to CH1 and you will not record any audio via the INPUT2 connector. - When you set the INPUT LEVEL selector to LINE. When you use an external microphone Make sure that the wind screen does not appear on the screen, using an underscan monitor. When you unplug the microphone plug Unplug it while holding the PUSH button down. When you connect equipment other than a microphone Set the +48V switch to OFF and the INPUT LEVEL selector to LINE. When detaching the XLR adaptor Unplug the hot shoe plug of the XLR adaptor from the intelligent accessory shoe beforehand. Detach the XLR adaptor after having loosened the screw of the XLR adaptor. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264

31
Recording – Basics
Note
If you use equipment other than a 48-V microphone with the +48V switch set to ON, a
malfunction of the equipment may occur. When you connect equipment other than a
48-V microphone, set it to OFF.
When the wind is blowing hard
Set INPUT1 of the LOW CUT switch to ON when the audio is input via the INPUT1
connector. Set INPUT2 to ON when the audio is input via the INPUT2 connector. The
sound of wind is reduced.
We recommend that you set MIC NR to OFF in the menu settings in the following
cases:
– When you use the external microphone at a distance from the camcorder.
– When the REC CH SELECT switch is set to CH1 and you will not record any audio via
the INPUT2 connector.
– When you set the INPUT LEVEL selector to LINE.
When you use an external microphone
Make sure that the wind screen does not appear on the screen, using an underscan
monitor.
When you unplug the microphone plug
Unplug it while holding the PUSH button down.
When you connect equipment other than a microphone
Set the +48V switch to OFF and the INPUT LEVEL selector to LINE.
When detaching the XLR adaptor
Unplug the hot shoe plug of the XLR adaptor from the intelligent accessory shoe
beforehand. Detach the XLR adaptor after having loosened the screw of the XLR
adaptor.
Recording a picture