Stihl MS 441 C-M MAGNUM174 Product Instruction Manual - Page 30

Tensioning the Chain, Checking Chain Tension

Get Stihl MS 441 C-M MAGNUM174 PDF manuals and user guides View all Stihl MS 441 C-M MAGNUM174 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

English Tensioning the Chain Checking Chain Tension Fuel 1 Retensioning during cutting work: N Shut off the engine. N Loosen the nuts. N Hold the bar nose up. N Use a screwdriver to turn the tensioning screw (1) clockwise until the chain fits snugly against the underside of the bar. N While still holding the bar nose up, tighten down the nuts firmly. N Go to "Checking Chain Tension". A new chain has to be retensioned more often than one that has been in use for some time. N Check chain tension frequently - see chapter on "Operating Instructions". 133BA024 KN 143BA007 KN N Shut off the engine. N Wear work gloves to protect your hands. N The chain must fit snugly against the underside of the bar and it must still be possible to pull the chain along the bar by hand. N If necessary, retension the chain. A new chain has to be retensioned more often than one that has been in use for some time. N Check chain tension frequently - see chapter on "Operating Instructions". This engine is certified to operate on unleaded gasoline and STIHL twostroke engine oil at a mix ratio of 50:1. Your engine requires a mixture of highquality gasoline and two-stroke air cooled engine oil. Use mid-grade unleaded gasoline with a minimum octane rating of 89 (R+M/2) and no more than 10% ethanol content. Fuel with a lower octane rating may increase engine temperatures. This, in turn, increases the risk of piston seizure and damage to the engine. The chemical composition of the fuel is also important. Some fuel additives not only detrimentally affect elastomers (carburetor diaphragms, oil seals, fuel lines, etc.), but magnesium castings and catalytic converters as well. This could cause running problems or even damage the engine. For this reason STIHL recommends that you use only high-quality unleaded gasoline! For further details, see www.STIHLusa.com/ethanol Use only STIHL two-stroke engine oil or equivalent high-quality two-stroke engine oils that are designed for use only in air cooled two-cycle engines. To ensure the maximum performance of your STIHL engine, use a high quality 2cycle engine oil. To help your engine run cleaner and reduce harmful carbon deposits, STIHL recommends using STIHL HP Ultra 2-cycle engine oil or ask your dealer for an equivalent fully synthetic 2-cycle engine oil. 28 MS 441 C-M

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
MS 441 C-M
English
28
Retensioning during cutting work:
N
Shut off the engine.
N
Loosen the nuts.
N
Hold the bar nose up.
N
Use a screwdriver to turn the
tensioning screw (1) clockwise until
the chain fits snugly against the
underside of the bar.
N
While still holding the bar nose up,
tighten down the nuts firmly.
N
Go to "Checking Chain Tension".
A new chain has to be retensioned more
often than one that has been in use for
some time.
N
Check chain tension frequently –
see chapter on "Operating
Instructions".
N
Shut off the engine.
N
Wear work gloves to protect your
hands.
N
The chain must fit snugly against
the underside of the bar and it must
still be possible to pull the chain
along the bar by hand.
N
If necessary, retension the chain.
A new chain has to be retensioned more
often than one that has been in use for
some time.
N
Check chain tension frequently –
see chapter on "Operating
Instructions".
This engine is certified to operate on
unleaded gasoline and STIHL two-
stroke engine oil at a mix ratio of 50:1.
Your engine requires a mixture of high-
quality gasoline and two-stroke air
cooled engine oil.
Use mid-grade unleaded gasoline with a
minimum octane rating of 89 (R+M/2)
and no more than 10% ethanol content.
Fuel with a lower octane rating may
increase engine temperatures. This, in
turn, increases the risk of piston seizure
and damage to the engine.
The chemical composition of the fuel is
also important. Some fuel additives not
only detrimentally affect elastomers
(carburetor diaphragms, oil seals, fuel
lines, etc.), but magnesium castings and
catalytic converters as well. This could
cause running problems or even
damage the engine. For this reason
STIHL recommends that you use only
high-quality unleaded gasoline!
For further details, see
www.STIHLusa.com/ethanol
Use only STIHL two-stroke engine oil or
equivalent high-quality two-stroke
engine oils that are designed for use
only in air cooled two-cycle engines.
To ensure the maximum performance of
your STIHL engine, use a high quality 2-
cycle engine oil. To help your engine run
cleaner and reduce harmful carbon
deposits, STIHL recommends using
STIHL HP Ultra 2-cycle engine oil or ask
your dealer for an equivalent fully
synthetic 2-cycle engine oil.
Tensioning the Chain
1
133BA024 KN
Checking Chain Tension
143BA007 KN
Fuel