Thermador HMWB36WS View Kitchen Design and Planning Guide - Page 65
Planning Information, Blower And Duct Selection Guide
View all Thermador HMWB36WS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 65 highlights
| THERMADOR | VENTILATION | THERMADOR | VENTILATION PLANNING INFORMATION Ventilation Installation Considerations Hood Width The hood width should be no less than the width of the cooking surface. Where space is not restricted, a wider hood can be used to increase your capture area. Distance from Cooking Surface Proper mounting height is very important. If a hood is mounted too low, it may be difficult to cook and be unsafe. If a hood is mounted too high, performance may be compromised. For optimal performance, the distance from the cooking surface to the bottom of the hood should be a minimum of 30", unless otherwise noted. Please refer to the installation manual for each hood and cooktop / range model for proper hood mounting heights. Available Ceiling Height The standard ceiling height can vary from region to region and in homes built in different eras. Ceiling heights, even in the same room, can sometimes vary by as much as several inches. Kitchen ceiling heights can vary between 7'6" (or 90") to over 10' (or 120"). Before selecting a Thermador Hood, check the available installation space and any extra space that may remain after proper installation of a hood and cooktop or range. This extra space can be filled using Thermador stainless steel duct cover accessories or integrated with kitchen cabinetry. The space can also be adjusted by raising or lowering your hood within the recommended range (typically 30" to 36" above the cooking surface). Choosing the Correct Blower A variety of interior and exterior blower options (Remote, Inline or Integrated) are available for Thermador Professional and Masterpiece® Hoods. If the unit you have selected does not have a blower, one can be purchased separately. Blower selection will vary based on the volume of air that needs to be moved and the length and location of the duct run. For long duct runs with multiple turns and bends, consider using a more powerful blower. For the most efficient air flow exhaust, use a straight run or as few elbows as possible. Remote Blowers (VTR Series) Depending on your preference and ducting situation, these blowers can be mounted on the roof or exterior wall of your home. An exterior installation may be more appealing to reduce noise in the kitchen. Inline Blowers (VTI Series) To minimize noise in the kitchen, these blowers are mounted along the duct line anywhere between the kitchen and the exterior wall. If you have easy access to your duct line (in an attic, for example), this may be an appealing option. Integrated Blowers (VTN series) These blowers are purchased separately and integrated into the hood or onto the downdraft unit at the time of installation. This option allows you to select your ideal hood with the exact power you require. Integrated blowers are included with HPWB30FS, HPWB36FS and HPWB48FS. SPECIAL NOTE: Always allow access to the blower for serviceability, should it be needed. Choosing the Right CFM The power of the cooktop or range, measured in BTU, is perhaps the most important factor in determining CFM needs for a hood. You should also consider the cooking space and cooking style of your client. • More demanding cooks usually require more exhaust capacity to handle moisture generated by boiling large pots of water or the grease and smoke resulting from grilling or frying. This cooking style could require a hood or downdraft system with airflow of 600 to 1,300 CFM. • For those who are used to preparing quick meals in a relatively small kitchen, a hood with 400 CFM may be adequate ventilation for the cooking space. • If the cooking surface is in a peninsula or island, a larger capacity hood can provide better capture when there are cross currents and when the hood needs to be mounted higher. Downdraft ventilation systems are also a good alternative. • High heat cooking or aromatic foods may require additional CFM. Increasing capture area by 3" on each side is also a recommended way to address this issue. Length and Size of Duct Work Do not use flexible duct; it creates back pressure / air turbulence and reduces performance. Straight runs and gradual turns are best. Use the shortest route with the fewest turns possible. Proper performance is dependent upon proper ducting. Use a qualified and trained installer. Local building codes may require the use of makeup air systems when using ducted ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area. If using a 10" duct, Thermador recommends not exceeding 50 feet of duct. Transitions, elbows and wall or roof caps are all factors that will add more static pressure, therefore increasing your equivalent duct run. 126 Visit Thermador.com for complete specifications or text a Thermador model number to 21432 to have specs sent to your phone BLOWER AND DUCT SELECTION GUIDE ACCESSORIES Type Model # Wall Hoods - Professional 60" - PH60GWS 54" - PH54GWS 48" - PH48GWS 42" - PH42GWS 36" - PH36GWS 48" - PH48HWS 36" - PH36HWS 30" - PH30HWS Remote Inline Integrated Remote Inline Integrated Remote Inline Integrated Remote Inline Integrated Remote Inline Integrated VTR2FZ VTI2FZ VTN2FZ VTR2FZ VTI2FZ VTN2FZ VTR2FZ VTI2FZ VTN2FZ VTR2FZ VTI2FZ VTN2FZ VTR1FZ VTR2FZ VTI1FZ VTI2FZ VTN1DZ VTN2FZ Wall Hoods - Masterpiece® 36" - HMWB36WS Use Recirculation Kit RECHMWB36 30" - HMWB30WS Use Recirculation Kit RECHMWB30 Integrated 48" - HMWB481WS 36" - HMWB361WS Integrated 36" - HMDW36WS 30" - HMDW30WS Use Recirculation Kit RECHMDW30 or RECHMDW36 Integrated Included Included Included Blower Information CFM Max. Total Amps (120V, 60Hz) Roofplate Required Hood Information Transition Duct Duct Size w/Backdraft Size at at Blower Damper Discharge Discharge Direction 1000 1000 1000 1000 600 1000 600 1000 400 1000 RFPLT1000P 16.3 10-inch Included 10-inch Vertical, Horizontal - 14.7 RFPLT1000P 15.5 10-inch Included 10-inch Vertical, Horizontal - 13.9 RFPLT1000P 11.1 10-inch Included 10-inch Vertical, Horizontal - 9.5 RFPLT1000P 10.3 10-inch Included 10-inch Vertical, Horizontal - 8.7 5.7 RFPLT600P 6-inch 10.3 RFPLT1000P 10-inch 5.7 6-inch Included 10-inch Vertical, Horizontal 10.3 10-inch - 3.3 6-inch 8.7 10-inch 600 3.4 1000 7.6 600 3.4 - 10-inch Included 10-inch Vertical - 10-inch Included 10-inch - 6-inch Included 10-inch Vertical Vertical 127