Toshiba 52HMX95 Owner's Manual - English - Page 55

Chapter 6: Setting up your TV Setting the AVHD device skip time Setting the time and date When you connect an external AVHD (audio/video hard drive) device-such as the Toshiba Symbio™ AVHD Recorder-to one of the TV's IEEE1394 ports, you can use the AVHD device skip time feature to set the number of minutes the device will skip forward or backward when you press the SKIP buttons. Note: • This TV will work best with the Toshiba Symbio™ AVHD Recorder* for recording high definition and standard definition material from either tuner and for controlling live TV (pause/rewind/etc.). When the Symbio AVHD Recorder is connected to the TV, the remote control keys (LIVE, STOP, REW, PAUSE, PLAY, etc.) are automatically activated to allow pausing of live TV. • When you connect an AVHD (or D-VHS) device, the TV Guide On Screen® system is automatically configured to allow recording. See page 26 for device connection information. See Chapters 5 and 7 for details about setting up and using the TV Guide On screen® system. To set the AVHD device skip time: 1. Press MENU and open the Setup menu. 2. Highlight AVHD Skip Time and press •. 3. Press y or z to select the AVHD skip time (1, 3, 5, or 15 minutes) and press ENTER. Setup Sleep Timer On/Off Timer PC Settings HDMI 1 Audio HDMI 2 Audio Slide Show Interval AVHD Skip Time AAutoo AAutoo 2 Sec 15 min 1 min 3 min A5 nmailnog 15 min Navigate Select CH RTN Back EXIT Exit *To enjoy the full benefits of your Toshiba Symbio™ AVHD Recorder, you must first set up the TV Guide On Screen® system (see Chapter 5). Full Symbio™ AVHD Recorder benefits, including Intelligent One Touch recording, will not be available unless the TV Guide On Screen® system is fully operational. However, even if the TV Guide On Screen® system is not fully operational, manual recording is available as long as the TV Guide On Screen® system has acquired the necessary date and time data. If you experience any issues with your Symbio AVHD Recorder, please contact Toshiba Consumer Solutions by calling (800) 631-3811 or visiting http://www.tacp.com/customersupport/contact.asp. Setting the HDMI™ audio mode Note: If you already set up the TV Guide On Screen® system, the time and date were set automatically and you can skip this step. To set the time and date: 1. Press MENU and open the Setup menu. 2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3 below.) 3. Open the Time And Date menu, highlight Start Setup, and press ENTER. Time And Date Start Setup Navigate Select CH RTN Back EXIT Exit If you have not set up the TV Guide On Screen® system, the following screen will appear. To set the time, highlight TV Guide On Screen® and press ENTER. The TV Guide On Screen® setup sequence will start, and the time and date will be set automatically. Time And Date Your TV Guide On Screen system can provide accurate time and date information. It is recommended you set up TV Guide On Screen first and use it to obtain the time and date. Manual TV Guide On Screen Cancel If you have already set up the TV Guide On Screen® system, or if you have not set up the time, the Time and Date setting screen will appear and you will need to manually set the time and date. Time And Date Date (MM/DD/YY) Time (HH:MM) 0 6/3 0/0 5 1 1 : 1 1 AM To set the HDMI audio mode: 1. Press MENU and open the Setup menu. Setup 2. Highlight HDMI 1 (or Installation Auto 2) Audio and press •. Sleep Timer On/Off Timer Digital Analog 3. Press z or y to select the HDMI audio mode (Auto, Digital, or PC Settings HDMI 1 Audio HDMI 2 Audio Slide Show Interval Auto Auto Auto 2 Sec Analog) and press Navigate Select CH RTN Back EXIT Exit ENTER. (Auto is the recommended mode). See "Connecting an HDMI or DVI device to the HDMI input" on page 21. Cancel Done Note: • If you highlight TV Guide On Screen® (above) to set the time and date through the TV Guide On Screen® system and a power outage occurs, the time and date will be updated automatically when the power is restored. • If you highlight Manual (above) to set the time and date manually and a power outage occurs, you will lose the time and date settings when the power is restored. • If you manually set the time and date and then perform TV Guide On Screen® setup, the manual time and date settings will be overridden by the TV Guide On Screen® settings. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 55