Toshiba PSM30C-7101U User Manual - Page 142

Removing memory module, System Properties, General

Get Toshiba PSM30C-7101U PDF manuals and user guides View all Toshiba PSM30C-7101U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 142 highlights

OPTIONAL DEVICES User's Manual 5. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Figure 8-6 Seating the memory module CAUTIONS: 1. Be careful not to drop the screw inside the computer. 2. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 6. Seat the memory module cover and secure it with one screw. 7. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power, for details. 8. Turn the power on and make sure the added memory is recognized. Open System Properties in the Control Panel and click the General tab. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn off the power and disconnect all cables from the computer. 2. Turn the computer upside down and remove the battery. 3. Loosen one screw securing the memory module cover and lift off the cover. Refer to figure 8-5. 4. Push the latches to the outside to release the module. A spring will force one end of the module up. 8-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
User's Manual
8-8
O
PTIONAL
D
EVICES
5.
Fit the memory module’s connectors into the socket at about a 45 degree angle
and push the module down until latches on either side snap into place.
Figure 8-6
Seating the memory module
CAUTIONS:
1.
Be careful not to drop the screw inside the computer.
2.
Do not touch the connectors on the memory module or
on the computer. Debris on the connectors may cause
memory access problems.
6.
Seat the memory module cover and secure it with one screw.
7.
Install the battery pack. Refer to
Replacing the battery pack
section in
Chapter 6,
Power
, for details.
8.
Turn the power on and make sure the added memory is recognized. Open
System Properties
in the Control Panel and click the
General
tab.
Removing memory module
To remove the memory module, make sure the computer is in boot mode then:
1.
Turn off the power and disconnect all cables from the computer.
2.
Turn the computer upside down and remove the battery.
3.
Loosen one screw securing the memory module cover and lift off the cover.
Refer to figure 8-5.
4.
Push the latches to the outside to release the module. A spring will force one
end of the module up.