Weed Eater ONE Owner Manual - Page 18
Muffler, Spark Plugs, Cleaning, Clean Air Intake/cooling Areas, Clean Air Screen, Important, Conozca - riding mower
View all Weed Eater ONE manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
4. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see "PRODUCT SPECIFICATIONS"sectionofthismanual. 5. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULL" line on dipstick. Tighten cap onto the tube securely when finished. AIR FILTER Your engine will not run properly using a dirty air filter. Replace the air filter every 100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions. 1. Remove cover knob and cover. 2. Carefully remove cartridge. 3. Clean base carefully to prevent debris from falling into carburetor. 4. Clean by gently tapping on a flat sur- face. 5. Reinstall cartridge, cover and secure with cover knob. Cover Knob Cover Air Filter NOTE: If very dirty or damaged, replace cartridge. IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean cartridge. CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. CLEAN AIR INTAKE/COOLING AREAS To ensure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times. Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled. NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating. MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS" section of this manual. CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your riding mower unless the engine and transmission are covered to keep water out. Water in engine or transmission will shorten the useful life of your riding mower. Use compressed air or a leaf blower to remove grass, leaves and trash from riding mower and mower. 18 CONOZCA SU CORTADORA DE CÉSPED LEA ESTE MANUAL DE OPERARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU CORTADORA DE CÉSPED Compare las ilustraciones con su cortadora de césped para familiarizarse con las ubicaciones de los diferentes controles y ajustes. Conserve este manual para futuras consultas. Pedal del freno Palanca del embrague de la plataforma Émbolo de la palanca del elevador Palanca de ajuste de altura Control de rueda libre Pedal del freno de estacionamiento (ROS) en posición "on" Interruptor de arranque Palanca de control de movimiento Nuestra cortadora de césped cumple con las normas de seguridad aplicables del Instituto Nacional Estadounidense de Normas. PALACA DEL EMBRAGUE DE LA PLATAFORMA - Se usa para activar la cuchilla de la cortadora de césped. PEDAL DEL FRENO - Se usa para frenar la cortadora de césped y arrancar el motor. PALANCA DE AJUSTE DE ALTURA - Se usa para ajustar la altura de corte de la cortadora de césped. INTERRUPTOR DE ARRANQUE - Se usa para arrancar y detener el motor. ÉMBOLO DE LA PALANCA DEL ELEVADOR Se usa para soltar la palanca de ajuste de altura cuando se cambia su posición. PALANCA DE FRENO DE ESTACIONAMIENTO - Fija el freno de estacionamiento en la posición de freno. PALANCA DE CONTROL DE MOVIMIENTO Selecciona la velocidad y dirección de la cortadora de césped. CONTROL DE RUEDA LIBRE - Desactiva la transmisión para empujar o remolcar despacio la cortadora de césped con el motor apagado. INTERRUPTOR DEL SISTEMA DE FUNCIONAMIENTO HACIA ATRÁS (ROS) EN POSICIÓN "ON" - Permite la operación del conjunto segador o otro accesorio accionado mientras que en revés. 35