Weider 7000 Crosstrainer English Manual - Page 12

WEIGHT, STACK, ASSEMBLY, Weight, Stack, position, BRACKET

Get Weider 7000 Crosstrainer PDF manuals and user guides View all Weider 7000 Crosstrainer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

PAGE 11 WEIDER SPORTING GOODS STEP 6 WEIGHT STACK ASSEMBLY PART.: NAME;::. 110 WEIGHT SELECTOR ENO TUBE CAP 114 LARGE RUBBER WASHER QTY. 2 CAUTION: To aid in this step it is advised that you secure ' the assistance of a helper to assist in steadying of the Weight Plates as they are stacked. 0 O 0 Locate the LARGE RUBBER WASHERS (114) atop the welded Guide Rod Bracket on the BASE "1" (1). With the aid of your helper, begin stacking the WEIGHT PLATES (12) atop the Rubber, Washers on the Guide Rod Bracket on the BASE (1). Ei Stack Weights one at a time until all but one are stacked on the Base. u insert the WEIGHT 24- 3 SELECTOR END TUBE CAP (110) Into the bottom end of the WEIGHT SELECTOR TUBE (13). Insert the Selector Tube Into the center hole through the stack of Weight Plates and align the pre-assembled roll pin of the Selector Tube with the groove in the top of the Weight Plate. NOTE: The Weight Selector Tube should Insert completely through the stack of Weight Plates If they are in proper alignment with the welded Guide Rod Bracket on the Base Frame. Ifit does not Insert completely, adjust the Weight Stack positioning untilit does. When the WEIGHT SELECTOR TUBE (13) has been inserted fully into the Weight Stack position the final WEIGHT PLATE (12) over the Selector Tube atop the Weight Stack CD 0 PRE-ASSEMBLED ROLL PIN 0 0 O 0 13 0 0 0 0 0 110 12 CD O O Ct 114 GUIDE ROD BRACKET

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
PAGE
11
WEIDER
SPORTING
GOODS
STEP
6
WEIGHT
STACK
ASSEMBLY
PART.:
NAME;::.
110
WEIGHT
SELECTOR
ENO
TUBE
CAP
QTY.
114
LARGE
RUBBER
WASHER
2
CAUTION:
To
aid
in
this
step
it
is
advised
that
you
secure
'
the
assistance
of
a
helper
to
assist
in
steadying
of
the
Weight
Plates
as
they
are
stacked.
Locate
the
LARGE
RUBBER
WASHERS
(114)
atop
the
welded
Guide
Rod
Bracket
on
the
BASE
"1"
(1).
With
the
aid
of
your
helper,
begin
stacking
the
WEIGHT
PLATES
(12)
atop
the
Rubber,
Washers
on
the
Guide
Rod
Bracket
on
the
BASE
(1).
Ei
Stack
Weights
one
at
a
time
until
all
but
one
are
stacked
on
the
Base.
insert
the
WEIGHT
2-
43
SELECTOR
END
TUBE
CAP (110)
Into
the
bottom
end
of
the
WEIGHT
SELECTOR
TUBE
(13).
Insert
the
Selector
Tube
Into
the
center
hole
through
the
stack
of
Weight
Plates
and
align
the
pre
-assembled
roll
pin
of
the
Selector
Tube
with
the
groove
in
the
top
of
the
Weight
Plate.
NOTE:
The
Weight
Selector
Tube
should
Insert
completely
through
the
stack
of
Weight
Plates
If
they
are
in
proper
alignment
with
the
welded
Guide
Rod
Bracket
on
the
Base
Frame.
If
it
does
not
Insert
completely,
adjust
the
Weight
Stack
positioning
until
it
does.
When
the
WEIGHT
SELECTOR
TUBE
(13)
has
been
inserted
fully
into
the
Weight
Stack
position
the
final
WEIGHT
PLATE
(12)
over
the
Selector
Tube
atop
the
Weight
Stack
12
114
0
0
GUIDE
ROD
BRACKET
CD
0
0
0
O
0
0
0
0
0
0
Ct
O
CD
O
PRE
-ASSEMBLED
ROLL
PIN
O
13
110