Xerox Z750/N Network Guide - Page 11

Token Ring parameters, Parameter, Description, Choices, Adapter status, Details, Broadcast

Get Xerox Z750/N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 042215455084
View all Xerox Z750/N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Token Ring Token Ring parameters Parameter Network Address Speed Early Token Release Adapter Status Description Token Ring Address (by default, this is a bit-swapped version of the printer's Printer ID, and it is a unique address on the network). You can supply a Locally Administered Address. Reports the ring speed set by the jumper on the card. The printer releases the token at the end of the last byte transmitted (not applicable at 4 Mbps). Reports the Token Ring card status. The report is in two parts, separated by a comma: Adapter status, Details Adapter status reports the condition of the Token Ring card. Details reports additional information. Route Cache Size The number of entries in the source route table. Route Cache Timeout The time in seconds that an entry remains in the source route table before being updated. Broadcast For broadcasting to all network nodes. Changes the default frame type for source route broadcasts. Broadcast is ignored if Frame Routing is set to Transparent. Note: Some protocols (such as IP) always use all routes, so they are not affected by this parameter. Unknown Route Used when the printer is searching for a route to a specific network node. Changes the default frame type for source route broadcasts. Unknown Route is ignored if Frame Routing is set to Transparent. Note: Some protocols (such as IP) always use all routes, so they are not affected by this parameter. Choices Any valid Token Ring address between 40.xx.xx.xx.xx.xx and 7F.xx.xx.xx.xx.xx. 4 Mbps or 16 Mbps. Enabled (default) or Disabled Adapter status: Adapter Initializing. Card is starting up. Adapter Open. Card is connected to the network. Adapter Closed. Card is not connected to the network. Adapter Fault. Card is defective. Details: Ring OK. Ready for network communication. Fault. Internal error; the card is defective. Cable Disconnected. Cable is not connected to the card. Ring Error. Network problem. Removed by network management. The network administrator has disabled the connection. 10 to 300. 5 to 65535. Single Route. The printer uses single-route broadcasts for most source-route broadcasts. All Routes. The printer uses all-routes broadcasts for all broadcasts. Single Route. The printer uses single-route broadcasts for most source-route broadcasts. All Routes. The printer uses all-routes broadcasts for all broadcasts. 6 PhaserShare Networking Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
6
PhaserShare Networking Manual
Token Ring
Token Ring parameters
Parameter
Description
Choices
Network
Address
Token Ring Address (by default, this
is a bit-swapped version of the
printer’s Printer ID, and it is a unique
address on the network).
You can
supply a Locally Administered
Address.
Any valid Token Ring address
between 40.
xx.xx.xx.xx.xx
and
7F.
xx.xx.xx.xx.xx
.
Speed
Reports the ring speed set by the
jumper on the card.
4 Mbps or 16 Mbps.
Early Token
Release
The printer releases the token at the
end of the last byte transmitted (not
applicable at 4 Mbps).
Enabled (default) or Disabled
Adapter Status
Reports the Token Ring card status.
The report is in two parts, separated
by a comma:
Adapter status
,
Details
Adapter status
reports the condition
of the Token Ring card.
Details
reports additional information.
Adapter status:
Adapter Initializing.
Card is starting
up.
Adapter Open.
Card is connected to
the network.
Adapter Closed.
Card is not
connected to the network.
Adapter Fault.
Card is defective.
Details:
Ring OK.
Ready for network
communication.
Fault.
Internal error; the card is
defective.
Cable Disconnected.
Cable is not
connected to the card.
Ring Error.
Network problem.
Removed by network management.
The
network administrator has
disabled the connection.
Route Cache Size
The number of entries in the source
route table.
10 to 300.
Route Cache
Timeout
The time in seconds that an entry
remains in the source route table
before being updated.
5 to 65535.
Broadcast
For broadcasting to all network nodes.
Changes the default frame type for
source route broadcasts.
Broadcast
is
ignored if
Frame Routing
is set to
Transparent.
Note: Some protocols (such as IP)
always use all routes, so they are not
affected by this parameter.
Single Route.
The printer uses
single-route broadcasts for most
source-route broadcasts.
All Routes.
The printer uses
all-routes broadcasts for all
broadcasts.
Unknown Route
Used when the printer is searching for
a route to a specific network node.
Changes the default frame type for
source route broadcasts.
Unknown
Route
is ignored if
Frame Routing
is
set to
Transparent
.
Note: Some protocols (such as IP)
always use all routes, so they are not
affected by this parameter.
Single Route.
The printer uses
single-route broadcasts for most
source-route broadcasts.
All Routes.
The printer uses
all-routes broadcasts for all
broadcasts.