Yamaha CLP-150 Owner's Manual - Page 115

CLP-170: Keyboard Stand, Assembly

Page 115 highlights

CLP-170: Keyboard Stand Assembly CAUTION • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage. • Be sure to tighten up all screws upon completing assembly of each unit. • To disassemble, reverse the assembly sequence given below. TIP The CLP-170 has an iAFC (Instrumental Active Field Control) effect. This uses the speaker on the rear of the instrument to create a sense of reverberation and spaciousness. In order to take full advantage of iAFC, we recommend that you do the following. • Position the Clavinova so that its rear panel is at least 10 cm away from the wall. • Perform the automatic adjustment after you turn on the power of the Clavinova for the first time, and after each time you move the Clavinova to a different location (page 86). Have a Phillips-head (+) screwdriver ready. Remove the following parts from the package. Assembly Parts 6 × 25 mm long screws ×4 1 4 × 20 mm tapping screws ×4 4 6 × 16 mm short screws ×6 2 Cord holders ×2 4 × 14 mm thin screws ×8 3 Main unit Front panel Side panel (left) Rear panel Side panel (right) Pedal box Bundled pedal cord inside AC power cord 1. Attach the side panels to the pedal box. (1) Stretch out the bundled pedal cord, and pass it through the hole. (2) Use the vinyl string to fasten the pedal cord. Side panel (left) (3) Use the four 6 × 25 mm long screws 1 to attach the pedal box. First attach one side panel, then attach the other side panel. Side panel (right) CLP-170/150 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124

CLP-170/150
115
CLP-170: Keyboard Stand
Assembly
CAUTION
Be careful not to confuse parts, and be sure to install
all parts in the correct direction. Please assemble in
accordance with the sequence given below.
Assembly should be carried out by at least two per-
sons.
Be sure to use the correct screw size, as indicated
below. Use of incorrect screws can cause damage.
Be sure to tighten up all screws upon completing
assembly of each unit.
To disassemble, reverse the assembly sequence given
below.
The CLP-170 has an iAFC (Instrumental Active Field Con-
trol) effect. This uses the speaker on the rear of the instru-
ment to create a sense of reverberation and spaciousness.
In order to take full advantage of iAFC, we recommend that
you do the following.
Position the Clavinova so that its rear panel is at least 10
cm away from the wall.
Perform the automatic adjustment after you turn on the
power of the Clavinova for the first time, and after each
time you move the Clavinova to a different location
(page 86).
Remove the following parts from the package.
1.
Attach the side panels to the pedal
box.
TIP
Have a Phillips-head (+) screwdriver ready.
Assembly Parts
6
×
25 mm long screws
×
4
1
4
×
14 mm thin screws
×
8
3
Cord holders
×
2
6
×
16 mm short screws
×
6
2
4
×
20 mm tapping
screws
×
4
4
Pedal box
Rear panel
Front panel
AC power cord
Main unit
Side panel
(left)
Side panel
(right)
Bundled pedal cord inside
Side panel
(left)
Side panel
(right)
(3)
Use the four 6
×
25 mm
long screws
1
to attach the
pedal box. First attach one
side panel, then attach the
other side panel.
(2)
Use the vinyl string to fasten
the pedal cord.
(1)
Stretch out the bundled ped-
al cord, and pass it through
the hole.