Yamaha DTX402K DTX402K/DTX432K/DTX452K Owners Manual - Page 16

Step 3, Assembling the rack, Attaching the snare pad

Get Yamaha DTX402K PDF manuals and user guides View all Yamaha DTX402K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Setup Assembly Guide Step 3 Assembling the rack Rack (Large) Rack (Small) Joint Top view 110° 110° 1. Loosen the  key bolt on the rack (Large) and turn the joint around before sliding the Small rack (in the next step). 2. Slide the Small rack fully back into the joint in Step 1. For the DTX452K, the snare pad will be attached to the Small rack in the following step. 3. Open the left and right legs as shown in the Top view. CAUTION The rack may topple over and cause injury if the left and right legs are opened too wide. 4. Tighten the one  and five s key bolts to secure the entire rack. NOTE The pads will be rotated into place in a later step. Step 4 For DTX452K Attaching the snare pad S wing bolt Snare pad Hexagonal rod 1. Take the snare pad and the S wing bolt and lightly tighten the S wing bolt. (Five or six turns is sufficient.) 2. Place the snare pad on the hexagonal rod and slide it fully back. Then tighten the S wing bolt to secure the snare pad in place. 3. Loosen the  key bolt and adjust the angle of the snare pad. When finished, retighten the  key bolt to secure the snare pad in place. 14 DTX402K DTX432K DTX452K Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Assembly Guide
14
Setup
DTX402K DTX432K DTX452K Owner’s Manual
Assembling the rack
1.
Loosen the
key bolt on the rack (Large) and turn the joint around before sliding the Small rack (in the next step).
2.
Slide the Small rack fully back into the joint in
Step 1
.
3.
Open the left and right legs as shown in the Top view.
4.
Tighten the one
and five
s
key bolts to secure the entire rack.
Attaching the snare pad
1.
Take the snare pad and the S wing bolt and lightly tighten the S wing bolt. (Five or six turns is sufficient.)
2.
Place the snare pad on the hexagonal rod and slide it fully back. Then tighten the S wing bolt to secure the snare pad in
place.
3.
Loosen the
key bolt and adjust the angle of the snare pad. When finished, retighten the
key bolt to secure the snare
pad in place.
For the
DTX452K
, the snare pad will be attached to the Small rack in the following step.
CAUTION
The rack may topple over and cause injury if the left and right legs are opened too wide.
The pads will be rotated into place in a later step.
Step 3
Rack (Small)
110°
Top view
Rack (Large)
Joint
110°
NOTE
Step 4
For DTX452K
S wing bolt
Hexagonal rod
Snare pad