Yamaha HTR-6180BL Owner's Manual - Page 119

ADDITIONAL, INFORMATION, English, Problem, Cause, Remedy, No picture or sound.

Get Yamaha HTR-6180BL - HTR 6180 AV Receiver PDF manuals and user guides
UPC - 027108930107
View all Yamaha HTR-6180BL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

Troubleshooting Problem Cause Remedy The volume level cannot be increased, or the sound is distorted. The sound effects cannot be recorded. A source cannot be recorded by a digital recording component connected to the DIGITAL OUTPUT jack. A source cannot be recorded by an analog component connected to the AUDIO OUT (REC) jacks. The sound field parameters and some other settings of this unit cannot be changed. This unit does not operate properly. No sound is heard from the connected HDMI component. "CHECK SP WIRES" appears in the front panel display. There is noise interference from digital or radio frequency equipment. The picture is disturbed. This unit suddenly enters the standby mode. The component connected to the AUDIO OUT (REC) jacks of this unit is turned off. It is not possible to record the sound effects with a recording component. The source component is not connected to the DIGITAL INPUT jacks of this unit. Some components cannot record Dolby Digital or DTS sources. (U.S.A. model only) HD Radio signals are not output at the DIGITAL OUTPUT jacks. The source component is not connected to the analog AUDIO IN jacks of this unit. XM Satellite Radio and SIRIUS Satellite Radio signals are not output at the AUDIO OUT (REC) jacks. "MEMORY GUARD" in "SET MENU" is set to "ON". The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. The HDMI component does not accept the multi-channel audio signals. Speaker cables are short-circuited. This unit is too close to the digital or highfrequency equipment. The video source uses scrambled or encoded signals to prevent dubbing. The internal temperature is too high and the overheat protection circuitry has been activated. Turn on the power of the component. Connect the source component to the DIGITAL INPUT jacks. Connect the recording component to the analog AUDIO OUT (REC) jacks. Connect the source component to the analog AUDIO IN jacks. Set "MEMORY GUARD" to "OFF". Disconnect the power cable from the AC wall outlet and then plug it in again after about 30 seconds. Convert the multi-channel audio signals to the 2-channel audio signals at the source component such as a DVD player. Make sure all speaker cables are connected correctly. Move this unit further away from such equipment. Wait about 1 hour for this unit to cool down and then turn it back on. See page - 21, 23 - 23 100 - - 14 - - ■ HDMI Problem Cause No picture or sound. The number of the connected HDMI components is over the limit. HDCP authentication failed. Remedy Reduce the number of the connected HDMI components. Check that the connected HDMI components support the HDCP copy protection standards. See page - - ADDITIONAL INFORMATION English 115 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
115
En
Troubleshooting
ADDITIONAL
INFORMATION
English
■
HDMI
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned off.
Turn on the power of the component.
—
The sound effects
cannot be recorded.
It is not possible to record the sound effects
with a recording component.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack.
The source component is not connected to
the DIGITAL INPUT jacks of this unit.
Connect the source component to the DIGITAL
INPUT jacks.
21, 23
Some components cannot record Dolby
Digital or DTS sources.
(U.S.A. model only)
HD Radio signals are not output at the
DIGITAL OUTPUT jacks.
Connect the recording component to the analog
AUDIO OUT (REC) jacks.
—
A source cannot be
recorded by an analog
component connected
to the AUDIO OUT
(REC) jacks.
The source component is not connected to
the analog AUDIO IN jacks of this unit.
Connect the source component to the analog AUDIO
IN jacks.
23
XM Satellite Radio and SIRIUS Satellite
Radio signals are not output at the AUDIO
OUT (REC) jacks.
The sound field
parameters and some
other settings of this
unit cannot be
changed.
“MEMORY GUARD” in “SET MENU” is
set to “ON”.
Set “MEMORY GUARD” to “OFF”.
100
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
—
No sound is heard
from the connected
HDMI component.
The HDMI component does not accept the
multi-channel audio signals.
Convert the multi-channel audio signals to the
2-channel audio signals at the source component such
as a DVD player.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
14
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to the digital or high-
frequency equipment.
Move this unit further away from such equipment.
—
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This unit suddenly
enters the standby
mode.
The internal temperature is too high and the
overheat protection circuitry has been
activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
Problem
Cause
Remedy
See
page
Problem
Cause
Remedy
See
page
No picture or sound.
The number of the connected HDMI
components is over the limit.
Reduce the number of the connected HDMI
components.
—
HDCP authentication failed.
Check that the connected HDMI components support
the HDCP copy protection standards.
—