Yamaha RX-V371 Owners Manual - Page 60

APPENDIX, Troubleshooting, General

Get Yamaha RX-V371 PDF manuals and user guides View all Yamaha RX-V371 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

APPENDIX Troubleshooting Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below, or if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. General Problem The power will not turn on. The unit enters standby mode soon after the power is turned on. This unit cannot be turned off or does not work properly. The unit enters standby mode. Cause Remedy The protection circuitry operated three times consecutively. As a safety precaution, when the protection circuitry operates three times consecutively, the capability to turn on the power is disabled. Please contact your nearest Yamaha dealer or service center to request repair. The power cable is not completely Connect the power cable properly to an AC inserted. wall outlet. The speaker impedance settings are incorrect. Set the speaker impedance to match your speakers. (When this unit is turned back on and "CHECK SP WIRES!" is displayed.) The protection circuitry has been activated because this unit was turned on while a speaker cable was shorted. Make sure that all speaker cables between this unit and speakers are connected properly. The internal microcomputer is hung-up due to an external electric shock (such as lightning or excessive static electricity) or by a drop in power supply voltage. Disconnect the power cable from the AC wall outlet, wait about 30 seconds and then plug it in again. The batteries in the remote control Replace all batteries. may have lost their charge. The protection circuitry has been activated because of a short circuit, etc. Check that the speaker impedance settings are correct. See page - - 10 12 - 4 10 Problem After display of a countdown on the front panel, the unit goes into standby mode. "Internal Error" is displayed on the front panel display. Sound/images suddenly go off. Cause If you do not use take any action, the Auto Power Down function operates. An internal error has occurred. Remedy Turn on the unit, and play the source again. In the Setup menu "AutoPowerDown" ("Func. Setup" → "AutoPowerDown"), increase the time until switching to standby mode, or turn off the Auto Power Down function. Please contact authorized Yamaha dealer or service center to request repair. See page - 49 - The protection circuitry has been Check that the speaker impedance settings 10 activated because of a short circuit, are correct. etc. Check that the speaker wires are not - touching each other, then turn the unit back on. The sleep timer has turned off the Turn on the unit, and play the source again. - unit. En 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
En
60
APPENDIX
Refer to the table below when this unit does not function properly.
If the problem you are experiencing is not listed below, or if the instructions below do not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service
center.
General
Troubleshooting
Problem
Cause
Remedy
See
page
The power will not
turn on.
The protection circuitry operated
three times consecutively.
As a safety precaution, when the protection
circuitry operates three times consecutively,
the capability to turn on the power is
disabled. Please contact your nearest
Yamaha dealer or service center to request
repair.
—
The unit enters
standby mode soon
after the power is
turned on.
The power cable is not completely
inserted.
Connect the power cable properly to an AC
wall outlet.
—
The speaker impedance settings
are incorrect.
Set the speaker impedance to match your
speakers.
10
(When this unit is turned back on
and “CHECK SP WIRES!” is
displayed.) The protection
circuitry has been activated
because this unit was turned on
while a speaker cable was shorted.
Make sure that all speaker cables between
this unit and speakers are connected
properly.
12
This unit cannot be
turned off or does
not work properly.
The internal microcomputer is
hung-up due to an external electric
shock (such as lightning or
excessive static electricity) or by a
drop in power supply voltage.
Disconnect the power cable from the AC
wall outlet, wait about 30 seconds and then
plug it in again.
—
The batteries in the remote control
may have lost their charge.
Replace all batteries.
4
The unit enters
standby mode.
The protection circuitry has been
activated because of a short circuit,
etc.
Check that the speaker impedance settings
are correct.
10
After display of a
countdown on the
front panel, the unit
goes into standby
mode.
If you do not use take any action,
the Auto Power Down function
operates.
Turn on the unit, and play the source again.
—
In the Setup menu “AutoPowerDown”
(“Func. Setup”
→
“AutoPowerDown”),
increase the time until switching to standby
mode, or turn off the Auto Power Down
function.
49
“Internal Error” is
displayed on the
front panel display.
An internal error has occurred.
Please contact authorized Yamaha dealer or
service center to request repair.
—
Sound/images
suddenly go off.
The protection circuitry has been
activated because of a short circuit,
etc.
Check that the speaker impedance settings
are correct.
10
Check that the speaker wires are not
touching each other, then turn the unit back
on.
—
The sleep timer has turned off the
unit.
Turn on the unit, and play the source again.
—
Problem
Cause
Remedy
See
page