ZyXEL EOC350-TA User Guide - Page 12

EOC350-TA

Page 12 highlights

Chapter 1 Introduction The following table describes the connections. Table 2 EOC350-TS Connections ITEM DESCRIPTION Power Switch This rocker switch has the following positions: • POWER DC IN: Push the rocker switch to POWER 12V DC when you want the EcoOnCn3e5c0te-TdSfrtoomrePcOeivWeEpRow1e2rVfrDomC-IaNpotowearpoouwtleert.oTuhteleitn. cluded power adaptor must be • LINE: power (Puupshtoth1earmocpk)efrrosmwitachcotaoxLiaIlNpEowwehreninsyeorutewr acnotntnheectEeOdCt3o5t0h-eTSINtoproerct.eiAve 48V~90V, 50Hz or 60 Hz AC input from coax is necessary. Power 12V DC-IN To receive power from a power outlet, connect the included power adapter from this port to a power outlet and make sure the rocker switch on the side is set to DC IN. Power 12V DCOUT To provide power (up to 1 amp) to a device, such as a PON switch, connect a cable with an RCA connector-to-DC plug to the device, connect a coaxial power inserter to the IN port, and push the rocker switch on the side to LINE. Ethernet Ports These are Gigabit Ethernet ports that can be used to connect a computer for initial configuration and then connect to a switch or broadband device with Internet access. Reset While EOC350-TS is on, use a pin to press and release this button to restart the EOC350TS. Press and hold for five seconds, then release to restore all EOC350-TS settings to the factory defaults, including the IP address (default 192.168.1.1). IN Connect this port to a satellite TV, cable TV or VHF/UHF antenna to receive analog video directly. The OUT port on the EOC350-TA can then be connected directly to an analog TV. OUT Connect this port to an existing coaxial cable outlet that is in the same coaxial network as the EOC350-TA in the building. 1.3 EOC350-TA The EOC350-TA is an Ethernet over Coax Terminal Adapter. The EOC350-TA extracts TV and Ethernet media from a coaxial distribution cable for consumption by end-user devices such as PCs and TVs. 1.3.1 LEDs The following table describes the EOC350-TA LEDs. Table 3 EOC350-TA LEDs LED DESCRIPTION QLTY This LED shows the Ethernet over Coaxial cable speed. Green is high, orange is medium and red is low. PWR This LED is on when the power is on. Note: None of the LEDs are on if the EOC350-TA is not receiving power. 12 EOC350 Series User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

Chapter 1 Introduction
EOC350 Series User’s Guide
12
The following table describes the connections.
1.3
EOC350-TA
The EOC350-TA is an Ethernet over Coax Terminal Adapter. The EOC350-TA extracts TV and
Ethernet media from a coaxial distribution cable for consumption by end-user devices such as PCs
and TVs.
1.3.1
LEDs
The following table describes the EOC350-TA LEDs.
Note: None of the LEDs are on if the EOC350-TA is not receiving power.
Table 2
EOC350-TS Connections
ITEM
DESCRIPTION
Power Switch
This rocker switch has the following positions:
POWER DC IN
: Push the rocker switch to
POWER 12V DC
when you want the
EOC350-TS to receive power from a power outlet. The included power adaptor must be
connected from
POWER 12V DC-IN
to a power outlet.
LINE
: Push the rocker switch to
LINE
when you want the EOC350-TS to receive
power (up to 1 amp) from a coaxial power inserter connected to the
IN
port. A
48V~90V, 50Hz or 60 Hz AC input from coax is necessary.
Power 12V DC-IN
To receive power from a power outlet, connect the included power adapter from this port
to a power outlet and make sure the rocker switch on the side is set to
DC IN
.
Power 12V DC-
OUT
To provide power (up to 1 amp) to a device, such as a PON switch, connect a cable with an
RCA connector-to-DC plug to the device, connect a coaxial power inserter to the
IN
port,
and push the rocker switch on the side to
LINE
.
Ethernet Ports
These are Gigabit Ethernet ports that can be used to connect a computer for initial
configuration and then connect to a switch or broadband device with Internet access.
Reset
While EOC350-TS is on, use a pin to press and release this button to restart the EOC350-
TS. Press and hold for five seconds, then release to restore all EOC350-TS settings to the
factory defaults, including the IP address (default 192.168.1.1).
IN
Connect this port to a satellite TV, cable TV or VHF/UHF antenna to receive analog video
directly. The
OUT
port on the EOC350-TA can then be connected directly to an analog TV.
OUT
Connect this port to an existing coaxial cable outlet that is in the same coaxial network as
the EOC350-TA in the building.
Table 3
EOC350-TA LEDs
LED
DESCRIPTION
QLTY
This LED shows the Ethernet over Coaxial cable speed. Green is high, orange is medium
and red is low.
PWR
This LED is on when the power is on.