Home » ZyXEL Manuals » Networking » ZyXEL EOC350-TA » Manual Viewer

ZyXEL EOC350-TA User Guide - Page 67

base on IP TOS/TC or DSCP

Get ZyXEL EOC350-TA PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Chapter 11 Telnet Table 50 Generic Telnet Commands (continued) COMMANDS ARGUMENTS [ ] IS OPTIONAL swqosq [-t ] [-p ] swqosrate swqostc swsmac [-m ] [-c ] DESCRIPTION Display or setup the QoS Queue Scheduling, and 802.1p or IP Priority scheme selection. • -t: schedule mode • strict: strict priority • wfq: weighted fair queue Q3/Q2/Q1/Q0 service weight 8/4/2/1 • mix: Q3 is strict, Q2/Q1/Q0 service weight=4/2/1 • -p: select QoS scheme • 0: base on 802.1p (default) • 1: base on IP TOS/TC or DSCP Display or setup bandwidth throttling on LAN1/ LAN2. • : configure LAN1 or LAN2 port • : direction, incoming (rx) or outgoing (tx) • : enable or disable control on this direction • : the maximum rate (multiply value by 64kbps). Range from 1 to 3125, bandwidth control is invalid if N >= 3125 (>200Mbps) Display or setup the QoS configuration for TCP/ UDP traffic classification, to assign a higher priority for up to 8 different TCP/UDP protocols. • : rule set index (0~2) • : activate or deactivate this set • : TCP/UDP port number (0~65535), • : select queue index (0~3) for this rule set to q0 (lowest priority) / q1 / q2 / q3 (highest priority) Display or setup the static MAC entry. A total of 8 entries can be setup. • : amx 8nteries • : bind the current MAC entry to LAN1 or LAN2 port, i.e. enable this MAC entry as static MAC • :disable this MAC entry, neither bind to LAN1 nor LAN2 • : remove the current MAC entry. Invalidate this MAC entry to the default 00-0000-00-00-00 EOC350 Series User's Guide 67

Section	Page
EOC350 Series	1
Contents Overview	3
Table of Contents	4
Introduction	9
1.1 Overview	9
1.1.1 Integrating the EOC350-TS and EOC350-TA with Satellite TV	9
1.1.2 Integrating the EOC350-TS and EOC350-TA with an STB	10
1.2 EOC350-TS	10
1.2.1 LEDs	11
1.2.2 Connections	11
1.3 EOC350-TA	12
1.3.1 LEDs	12
1.3.2 Connections	13
1.4 The RESET Button	13
1.5 Ways to Manage the EOC350-TS	14
The Web Configurator	15
2.1 Overview	15
2.1.1 Accessing the Web Configurator	15
2.2 Securing the EOC350-TS	16
2.3 The Web Configurator Layout	17
2.3.1 Navigation Panel	17
2.3.2 Main Window	18
System Setup	19
3.1 Overview	19
3.2 The System Setup Screen	19
Auto Configuration	21
4.1 Overview	21
4.2 The Auto Configuration Screen	21
EP Management	22
5.1 Overview	22
5.2 The EP Management Screen	22
5.3 The View Host Screen	23
5.4 The View Host Screen	24
5.5 Termination System Configuration	25
5.5.1 The EoC Screen (Privacy Mode)	25
5.5.2 The Port Screen	25
5.5.3 The QoS Screen	26
5.5.4 The IGMP Screen	27
5.5.5 The VLAN Screen	28
5.5.6 The Status Screen	29
5.6 Testing from the Termination System	29
5.7 Ether EP Default Profile Configuration	30
5.7.1 The EoC Screen	30
5.7.2 The Port Screen	31
5.7.3 The QoS Screen	32
5.7.4 The IGMP Screen	33
5.7.5 The VLAN Screen	33
5.7.6 The Filter Screen	34
5.8 EP Configuration	35
5.8.1 The EoC Screen	35
5.8.2 The Port Screen	35
5.8.3 The QoS Screen	37
5.8.4 The IGMP Screen	37
5.8.5 The VLAN Screen	38
5.8.6 The Filter Screen	39
5.8.7 The Status Screen	39
5.9 Testing from a Termination Adapter	40
5.9.1 Noise	40
5.9.2 Online Diag	41
5.10 Backup and Restore of Termination Adapter Configuration	42
5.10.1 Backup Configuration	42
5.10.2 Restore Configuration	43
5.11 Adding Offline Termination Adapters	43
Administration	45
6.1 Overview	45
6.2 The Administrator Screen	45
6.3 The Allowed Source Screen	46
6.4 The Telnet Setup Screen	47
6.5 The HTTP Setup Screen	48
6.6 The SNMP Setup Screen	49
6.7 The SNMP Trap Server Screen	49
System Log	51
7.1 Overview	51
7.2 The Syslog Setup Screen	51
7.3 The Syslog View Screen	52
System Time	53
8.1 Overview	53
8.2 The SNTP Setup Screen	53
8.3 The View Time Screen	54
Static MAC	55
9.1 Overview	55
9.2 The Static MAC Screen	55
Maintenance	56
10.1 Overview	56
10.2 Rebooting the System	56
10.3 Restoring Default Settings	56
10.4 Uploading Firmware	56
10.5 The Activate Firmware Screen	58
10.6 Backup and Restore	59
10.6.1 Backup Configuration	59
10.6.2 Restore Configuration	60
Telnet	61
11.1 Overview	61
11.2 Config Telnet Server	61
11.2.1 Command Format	61
11.2.2 Generic Command Sets	62
SNMP	71
12.1 Overview	71
Troubleshooting	73
13.1 Power, Hardware Connections, and LEDs	73
13.2 EOC350-TS Access and Login	74
13.3 Bandwidth and Connectivity	75
13.4 Resetting the EOC350-TS to Factory Defaults	76