Home » ZyXEL Manuals » Networking » ZyXEL EOC350-TA » Manual Viewer

ZyXEL EOC350-TA User Guide - Page 29

Testing from the Termination System

Get ZyXEL EOC350-TA PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 5 EP Management 5.5.6 The Status Screen Use this screen to see the status of the termination system's interfaces. Click EP Management > Ether > Config > Status on the local termination system device to show the following screen. Figure 18 EP Management > Ether > Config > Status (termination system) The following table describes the items in this screen. Table 17 EP Management > Ether > Config > Status (termination system) LABEL DESCRIPTION Status Link This shows whether the port is up or down. Speed/Duplex This shows the speed and the duplex mode of the Ethernet connection on this port. Flow Control This shows whether flow control is enabled on this port. Statistics CLEAR Click this to clear the port traffic statistics. RxPkt This shows how many packets have been received by this port. RxByte This shows how many bytes have been received by this port. TxPkt This shows how many packets have been sent from this port. TxByte This shows how many bytes have been sent from this port. Collision This shows how many Ethernet collisions have been detected on this port. Error This shows how many errors have been detected on this port. Refresh Back Click this to refresh this screen. Click Back to return to the previous screen. 5.6 Testing from the Termination System Follow these steps to measure the noise spectrum at the termination system's coax interface. 1 Click EP Management > Test in the termination system region of the screen. EOC350 Series User's Guide 29

Section	Page
EOC350 Series	1
Contents Overview	3
Table of Contents	4
Introduction	9
1.1 Overview	9
1.1.1 Integrating the EOC350-TS and EOC350-TA with Satellite TV	9
1.1.2 Integrating the EOC350-TS and EOC350-TA with an STB	10
1.2 EOC350-TS	10
1.2.1 LEDs	11
1.2.2 Connections	11
1.3 EOC350-TA	12
1.3.1 LEDs	12
1.3.2 Connections	13
1.4 The RESET Button	13
1.5 Ways to Manage the EOC350-TS	14
The Web Configurator	15
2.1 Overview	15
2.1.1 Accessing the Web Configurator	15
2.2 Securing the EOC350-TS	16
2.3 The Web Configurator Layout	17
2.3.1 Navigation Panel	17
2.3.2 Main Window	18
System Setup	19
3.1 Overview	19
3.2 The System Setup Screen	19
Auto Configuration	21
4.1 Overview	21
4.2 The Auto Configuration Screen	21
EP Management	22
5.1 Overview	22
5.2 The EP Management Screen	22
5.3 The View Host Screen	23
5.4 The View Host Screen	24
5.5 Termination System Configuration	25
5.5.1 The EoC Screen (Privacy Mode)	25
5.5.2 The Port Screen	25
5.5.3 The QoS Screen	26
5.5.4 The IGMP Screen	27
5.5.5 The VLAN Screen	28
5.5.6 The Status Screen	29
5.6 Testing from the Termination System	29
5.7 Ether EP Default Profile Configuration	30
5.7.1 The EoC Screen	30
5.7.2 The Port Screen	31
5.7.3 The QoS Screen	32
5.7.4 The IGMP Screen	33
5.7.5 The VLAN Screen	33
5.7.6 The Filter Screen	34
5.8 EP Configuration	35
5.8.1 The EoC Screen	35
5.8.2 The Port Screen	35
5.8.3 The QoS Screen	37
5.8.4 The IGMP Screen	37
5.8.5 The VLAN Screen	38
5.8.6 The Filter Screen	39
5.8.7 The Status Screen	39
5.9 Testing from a Termination Adapter	40
5.9.1 Noise	40
5.9.2 Online Diag	41
5.10 Backup and Restore of Termination Adapter Configuration	42
5.10.1 Backup Configuration	42
5.10.2 Restore Configuration	43
5.11 Adding Offline Termination Adapters	43
Administration	45
6.1 Overview	45
6.2 The Administrator Screen	45
6.3 The Allowed Source Screen	46
6.4 The Telnet Setup Screen	47
6.5 The HTTP Setup Screen	48
6.6 The SNMP Setup Screen	49
6.7 The SNMP Trap Server Screen	49
System Log	51
7.1 Overview	51
7.2 The Syslog Setup Screen	51
7.3 The Syslog View Screen	52
System Time	53
8.1 Overview	53
8.2 The SNTP Setup Screen	53
8.3 The View Time Screen	54
Static MAC	55
9.1 Overview	55
9.2 The Static MAC Screen	55
Maintenance	56
10.1 Overview	56
10.2 Rebooting the System	56
10.3 Restoring Default Settings	56
10.4 Uploading Firmware	56
10.5 The Activate Firmware Screen	58
10.6 Backup and Restore	59
10.6.1 Backup Configuration	59
10.6.2 Restore Configuration	60
Telnet	61
11.1 Overview	61
11.2 Config Telnet Server	61
11.2.1 Command Format	61
11.2.2 Generic Command Sets	62
SNMP	71
12.1 Overview	71
Troubleshooting	73
13.1 Power, Hardware Connections, and LEDs	73
13.2 EOC350-TS Access and Login	74
13.3 Bandwidth and Connectivity	75
13.4 Resetting the EOC350-TS to Factory Defaults	76