ZyXEL EOC350-TS User Guide - Page 28

The VLAN Screen

Get ZyXEL EOC350-TS PDF manuals and user guides View all ZyXEL EOC350-TS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Chapter 5 EP Management The following table describes the items in this screen. Table 15 EP Management > Ether > Config > IGMP (termination system) LABEL DESCRIPTION IGMP Snooping Select Enable to enable IGMP v1/2 fast leave. Select Disable if only IGMP v3 is implemented on the network. Apply Click Apply to save your settings. Back Click Back to return to the previous screen. 5.5.5 The VLAN Screen Use this screen to configure VLAN tagging on the termination system's interfaces. Click EP Management > Ether > Config > VLAN on the local termination system device and then select Enable from Tag VLAN to show the following screen. Figure 17 EP Management > Ether > Config > VLAN (termination system) The following table describes the items in this screen. Table 16 EP Management > Ether > Config > VLAN (termination system) LABEL DESCRIPTION Cascade Mode Tag V LAN Select Enable to enable VLAN tagging. Port This shows the port name for this row. Priority Select the 802.1Q priority applied to incoming frames. VID In Rule Out Rule Apply Back Select the 802.1Q VLAN ID applied to incoming frames. Select Accept All to forward all incoming frames regardless of VID. Select VID Matched to forward only the incoming frames that match the port VID. Select Tag to add an 802.1Q tag to egress frames. Select Untag to remove the 802.1Q tag from egress frames. Select Bypass to leave the tag of the frame alone. Click Apply to save your settings. Click Back to return to the previous screen. 28 EOC350 Series User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Chapter 5 EP Management
EOC350 Series User’s Guide
28
The following table describes the items in this screen.
5.5.5
The VLAN Screen
Use this screen to configure VLAN tagging on the termination system’s interfaces. Click
EP
Management
>
Ether
>
Config
>
VLAN
on the local termination system device and then select
Enable from
Tag VLAN
to show the following screen.
Figure 17
EP Management > Ether > Config > VLAN (termination system)
The following table describes the items in this screen.
Table 15
EP Management > Ether > Config > IGMP (termination system)
LABEL
DESCRIPTION
IGMP Snooping
Select
Enable
to enable IGMP v1/2 fast leave. Select
Disable
if only IGMP v3 is
implemented on the network.
Apply
Click
Apply
to save your settings.
Back
Click
Back
to return to the previous screen.
Table 16
EP Management > Ether > Config > VLAN (termination system)
LABEL
DESCRIPTION
Cascade Mode
Tag VLAN
Select
Enable
to enable VLAN tagging.
Port
This shows the port name for this row.
Priority
Select the 802.1Q priority applied to incoming frames.
VID
Select the 802.1Q VLAN ID applied to incoming frames.
In Rule
Select
Accept All
to forward all incoming frames regardless of VID. Select
VID Matched
to
forward only the incoming frames that match the port VID.
Out Rule
Select
Tag
to add an 802.1Q tag to egress frames. Select
Untag
to remove the 802.1Q tag
from egress frames. Select
Bypass
to leave the tag of the frame alone.
Apply
Click
Apply
to save your settings.
Back
Click
Back
to return to the previous screen.