Home » ZyXEL Manuals » Networking » ZyXEL EX5510-B0 » Manual Viewer

ZyXEL EX5510-B0 User Guide - Page 272

Label, Description

Add to My Manuals
Save this manual to your list of manuals

Page 272 highlights

Chapter 36 Diagnostic Figure 176 Maintenance > Diagnostic > 802.3ah The following table describes the labels in this screen. Table 122 Maintenance > Diagnostics > 802.3ah LABEL DESCRIPTION IEEE 802.3ah Ethernet OAM Interface OAM ID Auto Event Features Click this switch to enable or disable the Ethernet OAM on the specified interface. When the switch goes to the right , the function is enabled. Otherwise, it is not. Select the interface on which you want to enable the IEEE802.3ah. Enter a positive integer to identify this node. Click this switch to detect link status and send a notification when an error (such as errors in symbol, frames, or seconds) is detected. Otherwise, disable this and you will not be notified. When the switch goes to the right , the function is enabled. Otherwise, it is not. Select Variable Retrieval so the Zyxel Device can respond to requests for information, such as requests for Ethernet counters and statistics, about link events. Select Link Events so the Zyxel Device can interpret link events, such as link fault and dying asp.Link events are set in event notification PDUs (Protocol Data Units), and indicate when the number of errors in a certain given interval (time, number of frames, number of symbols, or number of error frame seconds) exceeds a specified threshold. Organizations may create organization-specific link event TLVs as well. Select Remote Loopback so the Zyxel Device can accept loopback control PDUs to convert Zyxel Device into loopback mode. Apply Select Active Mode so the Zyxel Device initiates OAM discovery, send information PDUs; and may send event notification PDUs, variable request/response PDUs, or loopback control PDUs. Click this button to save your changes. EX5510-B0 User's Guide 272

Section	Page
EX5510-B0	1
Document Conventions	3
Contents Overview	4
Table of Contents	6
User’s Guide	15
Introducing the Zyxel Device	16
1.1 Overview	16
1.1.1 Multi-Gigabit Ethernet	16
1.2 Example Applications	16
1.2.1 Internet Access	17
1.2.2 Dual-Band WiFi	17
1.3 Ways to Manage the Zyxel Device	18
1.4 Good Habits for Managing the Zyxel Device	19
1.5 Hardware	19
1.5.1 Front Panel	19
1.5.2 Rear Panel	20
1.5.3 WPS Button	21
1.5.4 RESET Button	21
The Web Configurator	22
2.1 Overview	22
2.1.1 Accessing the Web Configurator	22
2.2 Web Configurator Layout	25
2.2.1 Navigation Panel	25
Quick Start Wizard	31
3.1 Overview	31
3.2 Wizard Setup	31
3.2.1 Time Zone	31
3.2.2 Internet	32
3.2.3 WiFi	34
Tutorials	36
4.1 Overview	36
4.2 Setting Up a Secure Wireless Network	36
4.2.1 Configuring the Wireless Network Settings	36
4.2.2 Using WPS	38
4.2.3 Without WPS	42
4.3 Setting Up Multiple Wireless Groups	43
4.4 Configuring Static Route for Routing to Another Network	47
4.5 Configuring QoS Queue and Class Setup	49
4.6 Access the Zyxel Device Using DDNS	53
4.6.1 Registering a DDNS Account on www.dyndns.org	53
4.6.2 Configuring DDNS on Your Zyxel Device	54
4.6.3 Testing the DDNS Setting	54
4.7 Configuring the MAC Address Filter	55
Technical Reference	57
Connection Status	58
5.1 Overview	58
5.1.1 Layout Icon	59
5.1.2 Connectivity	59
5.1.3 System Info	60
5.2 WiFi Settings	63
5.3 Guest WiFi Settings	64
5.4 LAN Settings	66
5.5 Parental Control	67
5.5.1 Create/Edit a Parental Control Profile	68
5.5.2 Define a Schedule	69
Broadband	71
6.1 Overview	71
6.1.1 What You Can Do in this Chapter	71
6.1.2 What You Need to Know	71
6.1.3 Before You Begin	74
6.2 Broadband Settings	74
6.2.1 Add/Edit Internet Connection	75
6.3 Technical Reference	82
Wireless	85
7.1 Wireless Overview	85
7.1.1 What You Can Do in this Chapter	85
7.1.2 What You Need to Know	85
7.2 Wireless General Settings	86
7.2.1 No Security	89
7.2.2 More Secure (Recommended)	89
7.3 Guest/More AP	91
7.3.1 Edit Guest/More AP Settings	92
7.4 MAC Authentication	95
7.4.1 Add/Edit MAC Addresses	96
7.5 WPS Settings	96
7.6 WMM Settings	98
7.7 Others Settings	99
7.8 Channel Status Settings	102
7.9 Band Steering	102
7.10 Technical Reference	103
7.10.1 Wireless Network Overview	103
7.10.2 Additional Wireless Terms	105
7.10.3 Wireless Security Overview	105
7.10.4 Signal Problems	107
7.10.5 BSS	107
7.10.6 MBSSID	108
7.10.7 Preamble Type	108
7.10.8 WiFi Protected Setup (WPS)	109
Home Networking	116
8.1 Home Networking Overview	116
8.1.1 What You Can Do in this Chapter	116
8.1.2 What You Need To Know	116
8.1.3 Before You Begin	118
8.2 LAN Setup	118
8.3 LAN Static DHCP	122
8.4 UPnP Settings	124
8.4.1 Turning on UPnP in Windows 7 Example	125
8.4.2 Turning on UPnP in Windows 10 Example	127
8.5 LAN Additional Subnet	129
8.6 STB Vendor ID	131
8.7 Wake on LAN	131
8.8 TFTP Server Name	132
8.9 Technical Reference	133
8.9.1 LANs, WANs and the Zyxel Device	133
8.9.2 DHCP Setup	133
8.9.3 DNS Server Addresses	134
8.9.4 LAN TCP/IP	134
Routing	136
9.1 Overview	136
9.2 Static Route Settings	136
9.2.1 Add/Edit Static Route	137
9.3 DNS Route	139
9.3.1 Add DNS Route	139
9.4 Policy Route	140
9.4.1 Add/Edit Policy Route	142
9.5 RIP Settings	143
Quality of Service (QoS)	144
10.1 QoS Overview	144
10.1.1 What You Can Do in this Chapter	144
10.2 What You Need to Know	145
10.3 Quality of Service General Settings	146
10.4 Queue Setup	148
10.4.1 Adding a QoS Queue	149
10.5 QoS Classification Setup	150
10.5.1 Add/Edit QoS Class	151
10.6 QoS Shaper Setup	155
10.6.1 Add/Edit a QoS Shaper	156
10.7 QoS Policer Setup	156
10.7.1 Add/Edit a QoS Policer	157
10.8 QoS Monitor	159
10.9 Technical Reference	160
Network Address Translation (NAT)	165
11.1 NAT Overview	165
11.1.1 What You Can Do in this Chapter	165
11.1.2 What You Need To Know	165
11.2 Port Forwarding	166
11.2.1 Add/Edit Port Forwarding	168
11.3 Port Triggering	170
11.3.1 Add/Edit Port Triggering Rule	172
11.4 DMZ Settings	173
11.5 ALG Settings	174
11.6 Address Mapping	175
11.6.1 Add/Edit Address Mapping Rule	176
11.7 NAT Sessions	177
11.8 Technical Reference	178
11.8.1 NAT Definitions	178
11.8.2 What NAT Does	179
11.8.3 How NAT Works	179
11.8.4 NAT Application	180
Dynamic DNS Setup	182
12.1 DNS Overview	182
12.1.1 What You Can Do in this Chapter	182
12.1.2 What You Need To Know	182
12.2 DNS Entry	183
12.2.1 Add/Edit DNS Entry	183
12.3 Dynamic DNS	184
IGMP/MLD	186
13.1 IGMP/MLD Overview	186
13.1.1 What You Need To Know	186
13.2 IGMP/MLD Settings	186
VLAN Group	189
14.1 Overview	189
14.1.1 What You Can Do in this Chapter	189
14.2 VLAN Group Settings	190
14.2.1 Add/Edit a VLAN Group	190
Interface Grouping	192
15.1 Interface Grouping Overview	192
15.1.1 What You Can Do in this Chapter	192
15.2 Interface Grouping Setup	192
15.2.1 Interface Group Configuration	193
15.2.2 Interface Grouping Criteria	195
Firewall	197
16.1 Firewall Overview	197
16.1.1 What You Can Do in this Chapter	197
16.1.2 What You Need to Know	198
16.2 Firewall Settings	198
16.3 Protocol Settings	200
16.3.1 Add New/Edit Protocol Entry	200
16.4 Access Control	201
16.4.1 Add/Edit an ACL Rule	202
16.5 DoS Settings	204
MAC Filter	206
17.1 MAC Filter Overview	206
17.2 MAC Filter Settings	206
Parental Control	208
18.1 Parental Control Overview	208
18.2 Parental Control Settings	208
18.2.1 Add/Edit a Parental Control Profile	209
Scheduler Rule	215
19.1 Scheduler Rule Overview	215
19.2 Scheduler Rule Settings	215
19.2.1 Add/Edit a Schedule Rule	216
Certificates	217
20.1 Certificates Overview	217
20.1.1 What You Can Do in this Chapter	217
20.2 What You Need to Know	217
20.3 Local Certificates	217
20.3.1 Create Certificate Request	219
20.3.2 View Certificate Request	219
20.4 Trusted CA	221
20.4.1 View Trusted CA Certificate	222
20.4.2 Import Trusted CA Certificate	223
Log	224
21.1 Log Overview	224
21.1.1 What You Can Do in this Chapter	224
21.1.2 What You Need To Know	224
21.2 System Log	225
21.3 Security Log	226
Traffic Status	227
22.1 Traffic Status Overview	227
22.1.1 What You Can Do in this Chapter	227
22.2 WAN Status	227
22.3 LAN Status	228
22.4 NAT Status	229
ARP Table	231
23.1 ARP Table Overview	231
23.1.1 How ARP Works	231
23.2 ARP Table Settings	232
Routing Table	233
24.1 Routing Table Overview	233
24.2 Routing Table Settings	233
Multicast Status	236
25.1 Multicast Status Overview	236
25.2 IGMP Status	236
25.3 MLD Status	237
WLAN Station Status	238
26.1 WLAN Station Status Overview	238
System	240
27.1 System Overview	240
27.2 System Settings	240
User Account	241
28.1 User Account Overview	241
28.2 User Account Settings	241
28.2.1 User Account Add/Edit	242
Remote Management	244
29.1 Remote Management Overview	244
29.1.1 What You Can Do in this Chapter	244
29.2 MGMT Services	244
29.3 Trust Domain	246
29.3.1 Add Trust Domain	246
SNMP	248
30.1 SNMP Overview	248
30.2 SNMP Settings	249
Time Settings	251
31.1 Time Settings Overview	251
31.2 Time	251
E-mail Notification	254
32.1 E-mail Notification Overview	254
32.2 E-mail Notification Settings	254
32.2.1 E-mail Notification Edit	255
Log Setting	257
33.1 Logs Setting Overview	257
33.2 Log Settings	257
33.2.1 Example E-mail Log	259
Firmware Upgrade	261
34.1 Firmware Upgrade Overview	261
34.2 Firmware Upgrade Settings	261
Backup/Restore	264
35.1 Backup/Restore Overview	264
35.2 Backup/Restore Settings	264
35.3 Reboot	266
Diagnostic	268
36.1 Diagnostic Overview	268
36.1.1 What You Can Do in this Chapter	268
36.2 What You Need to Know	268
36.3 Ping & TraceRoute & NsLookup	269
36.4 802.1ag (CFM)	270
36.5 802.3ah (OAM)	271
Troubleshooting and Appendices	273
Troubleshooting	274
37.1 Power, Hardware Connections, and LEDs	274
37.2 Zyxel Device Access and Login	275
37.3 Internet Access	276
37.4 Wireless Internet Access	278
37.5 UPnP	278
37.6 IP Address Setup	279
Customer Support	282
IPv6	288
Services	296
Legal Information	300