Home » ZyXEL Manuals » Networking » ZyXEL MES-3728 » Manual Viewer

ZyXEL MES-3728 User Guide - Page 121

Table 22

Get ZyXEL MES-3728 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Chapter 11 Static Multicast Forward Setup The following table describes the labels in this screen. Table 22 Advanced Application > Static Multicast Forwarding LABEL DESCRIPTION Active Select this check box to activate your rule. You may temporarily deactivate a rule without deleting it by clearing this check box. Name Type a descriptive name (up to 32 printable ASCII characters) for this static multicast MAC address forwarding rule. This is for identification only. MAC Address Enter a multicast MAC address which identifies the multicast group. The last binary bit of the first octet pair in a multicast MAC address must be 1. For example, the first octet pair 00000001 is 01 and 00000011 is 03 in hexadecimal, so 01:00:5e:00:00:0A and 03:00:5e:00:00:27 are valid multicast MAC addresses. VID You can forward frames with matching destination MAC address to port(s) within a VLAN group. Enter the ID that identifies the VLAN group here. If you don't have a specific target VLAN, enter 1. Port Enter the port(s) where frames with destination MAC address that matched the entry above are forwarded. You can enter multiple ports separated by (no space) comma (,) or hyphen (-). For example, enter "3-5" for ports 3, 4, and 5. Enter "3,5,7" for ports 3, 5, and 7. Add Click Add to save your rule to the Switch's run-time memory. The Switch loses this rule if it is turned off or loses power, so use the Save link on the top navigation panel to save your changes to the non-volatile memory when you are done configuring. Cancel Click Cancel to reset the fields to their last saved values. Clear Click Clear to begin configuring this screen afresh. Index Click an index number to modify a static multicast MAC address rule for port(s). Active This field displays whether a static multicast MAC address forwarding rule is active (Yes) or not (No). You may temporarily deactivate a rule without deleting it. Name This field displays the descriptive name for identification purposes for a static multicast MAC address-forwarding rule. MAC Address This field displays the multicast MAC address that identifies a multicast group. VID This field displays the ID number of a VLAN group to which frames containing the specified multicast MAC address will be forwarded. Port This field displays the port(s) within a identified VLAN group to which frames containing the specified multicast MAC address will be forwarded. Delete Click Delete to remove the selected entry from the summary table. Cancel Click Cancel to clear the Delete check boxes. MES-3728 User's Guide 121

Section	Page
MES-3728	1
About This User's Guide	3
Document Conventions	5
Safety Warnings	7
Contents Overview	9
Table of Contents	11
Introduction and Hardware	21
Getting to Know Your Switch	23
1.1 Introduction	23
1.1.1 Backbone Application	23
1.1.2 Bridging Example	24
1.1.3 High Performance Switching Example	25
1.1.4 IEEE 802.1Q VLAN Application Examples	25
1.1.5 Metro Ethernet	26
1.2 Ways to Manage the Switch	27
1.3 Good Habits for Managing the Switch	28
Hardware Installation and Connection	29
2.1 Installation Scenarios	29
2.2 Desktop Installation Procedure	29
2.3 Mounting the Switch on a Rack	29
2.3.1 Rack-mounted Installation Requirements	30
2.3.2 Attaching the Mounting Brackets to the Switch	30
2.3.3 Mounting the Switch on a Rack	31
Hardware Overview	33
3.1 Front Panel	33
3.1.1 Console Port	34
3.1.2 Gigabit Ethernet Ports	34
3.1.3 Mini-GBIC Slots	35
3.1.4 Management Port	37
3.1.5 Power Connector	37
3.1.6 Signal Slot	39
3.2 Rear Panel	41
3.2.1 External Backup Power Supply Connector	41
3.3 LEDs	42
Basic Configuration	45
The Web Configurator	47
4.1 Introduction	47
4.2 System Login	47
4.3 The Status Screen	48
4.3.1 Change Your Password	53
4.4 Saving Your Configuration	53
4.5 Switch Lockout	54
4.6 Resetting the Switch	54
4.6.1 Reload the Configuration File	54
4.7 Logging Out of the Web Configurator	56
4.8 Help	56
Initial Setup Example	57
5.1 Overview	57
5.1.1 Creating a VLAN	57
5.1.2 Setting Port VID	59
5.2 Configuring Switch Management IP Address	60
Tutorials	63
6.1 How to Use DHCP Snooping on the Switch	63
6.2 How to Use DHCP Relay on the Switch	67
6.2.1 DHCP Relay Tutorial Introduction	67
6.2.2 Creating a VLAN	68
6.2.3 Configuring DHCP Relay	71
6.2.4 Troubleshooting	72
System Status and Port Statistics	73
7.1 Overview	73
7.2 Port Status Summary	74
7.2.1 Status: Port Details	75
Basic Setting	79
8.1 Overview	79
8.2 System Information	80
8.3 General Setup	82
8.4 Introduction to VLANs	84
8.5 Switch Setup Screen	85
8.6 IP Setup	87
8.6.1 Management IP Addresses	87
8.7 Port Setup	90
Advanced	93
VLAN	95
9.1 Introduction to IEEE 802.1Q Tagged VLANs	95
9.1.1 Forwarding Tagged and Untagged Frames	95
9.2 Automatic VLAN Registration	96
9.2.1 GARP	96
9.2.2 GVRP	96
9.3 Port VLAN Trunking	97
9.4 Select the VLAN Type	98
9.5 Static VLAN	98
9.5.1 VLAN Status	99
9.5.2 VLAN Details	100
9.5.3 Configure a Static VLAN	101
9.5.4 Configure VLAN Port Settings	103
9.6 Subnet Based VLANs	105
9.7 Configuring Subnet Based VLAN	106
9.8 Protocol Based VLANs	107
9.9 Configuring Protocol Based VLAN	108
9.10 Create an IP-based VLAN Example	110
9.11 Port-based VLAN Setup	111
9.11.1 Configure a Port-based VLAN	112
Static MAC Forward Setup	115
10.1 Overview	115
10.2 Configuring Static MAC Forwarding	115
Static Multicast Forward Setup	119
11.1 Static Multicast Forwarding Overview	119
11.2 Configuring Static Multicast Forwarding	120
Filtering	123
12.1 Configure a Filtering Rule	123
Spanning Tree Protocol	125
13.1 STP/RSTP Overview	125
13.1.1 STP Terminology	125
13.1.2 How STP Works	126
13.1.3 STP Port States	127
13.1.4 Multiple RSTP	127
13.1.5 Multiple STP	128
13.2 Spanning Tree Protocol Status Screen	131
13.3 Spanning Tree Configuration	132
13.4 Configure Rapid Spanning Tree Protocol	133
13.5 Rapid Spanning Tree Protocol Status	135
13.6 Configure Multiple Rapid Spanning Tree Protocol	137
13.7 Multiple Rapid Spanning Tree Protocol Status	139
13.8 Configure Multiple Spanning Tree Protocol	141
13.9 Multiple Spanning Tree Protocol Status	144
Bandwidth Control	147
14.1 Bandwidth Control Overview	147
14.1.1 CIR and PIR	147
14.2 Bandwidth Control Setup	148
Broadcast Storm Control	151
15.1 Broadcast Storm Control Setup	151
Mirroring	153
16.1 Port Mirroring Setup	153
Link Aggregation	155
17.1 Link Aggregation Overview	155
17.2 Dynamic Link Aggregation	155
17.2.1 Link Aggregation ID	156
17.3 Link Aggregation Status	157
17.4 Link Aggregation Setting	159
17.5 Link Aggregation Control Protocol	161
17.6 Static Trunking Example	162
Port Authentication	165
18.1 Port Authentication Overview	165
18.1.1 IEEE 802.1x Authentication	165
18.1.2 MAC Authentication	166
18.2 Port Authentication Configuration	167
18.2.1 Activate IEEE 802.1x Security	168
18.2.2 Activate MAC Authentication	169
Port Security	171
19.1 About Port Security	171
19.2 Port Security Setup	172
19.3 VLAN MAC Address Limit	174
Classifier	177
20.1 About the Classifier and QoS	177
20.2 Configuring the Classifier	177
20.3 Viewing and Editing Classifier Configuration	180
20.4 Classifier Example	182
Policy Rule	185
21.1 Policy Rules Overview	185
21.1.1 DiffServ	185
21.1.2 DSCP and Per-Hop Behavior	185
21.2 Configuring Policy Rules	186
21.3 Viewing and Editing Policy Configuration	189
21.4 Policy Example	191
Queuing Method	193
22.1 Queuing Method Overview	193
22.1.1 Strictly Priority Queuing	193
22.1.2 Weighted Fair Queuing	193
22.1.3 Weighted Round Robin Scheduling (WRR)	194
22.2 Configuring Queuing	195
VLAN Stacking	197
23.1 VLAN Stacking Overview	197
23.1.1 VLAN Stacking Example	197
23.2 VLAN Stacking Port Roles	198
23.3 VLAN Tag Format	199
23.3.1 Frame Format	199
23.4 Configuring VLAN Stacking	200
23.4.1 Port-based Q-in-Q	201
23.4.2 Selective Q-in-Q	202
Multicast	205
24.1 Multicast Overview	205
24.1.1 IP Multicast Addresses	205
24.1.2 IGMP Filtering	205
24.1.3 IGMP Snooping	206
24.1.4 IGMP Snooping and VLANs	206
24.2 Multicast Status	206
24.3 Multicast Setting	207
24.4 IGMP Snooping VLAN	210
24.5 IGMP Filtering Profile	211
24.6 MVR Overview	213
24.6.1 Types of MVR Ports	213
24.6.2 MVR Modes	214
24.6.3 How MVR Works	214
24.7 General MVR Configuration	215
24.8 MVR Group Configuration	217
24.8.1 MVR Configuration Example	218
AAA	221
25.1 Authentication, Authorization and Accounting (AAA)	221
25.1.1 Local User Accounts	222
25.1.2 RADIUS and TACACS+	222
25.2 AAA Screens	222
25.2.1 RADIUS Server Setup	223
25.2.2 TACACS+ Server Setup	225
25.2.3 AAA Setup	227
25.2.4 Vendor Specific Attribute	230
25.3 Supported RADIUS Attributes	231
25.3.1 Attributes Used for Authentication	232
25.3.2 Attributes Used for Accounting	233
IP Source Guard	235
26.1 IP Source Guard Overview	235
26.1.1 DHCP Snooping Overview	236
26.1.2 ARP Inspection Overview	238
26.2 IP Source Guard	239
26.3 IP Source Guard Static Binding	240
26.4 DHCP Snooping	243
26.5 DHCP Snooping Configure	247
26.5.1 DHCP Snooping Port Configure	249
26.5.2 DHCP Snooping VLAN Configure	250
26.6 ARP Inspection Status	252
26.6.1 ARP Inspection VLAN Status	253
26.6.2 ARP Inspection Log Status	254
26.7 ARP Inspection Configure	255
26.7.1 ARP Inspection Port Configure	257
26.7.2 ARP Inspection VLAN Configure	259
Loop Guard	261
27.1 Loop Guard Overview	261
27.2 Loop Guard Setup	263
VLAN Mapping	265
28.1 VLAN Mapping Overview	265
28.1.1 VLAN Mapping Example	265
28.2 Enabling VLAN Mapping	266
28.3 Configuring VLAN Mapping	267
Layer 2 Protocol Tunneling	269
29.1 Layer 2 Protocol Tunneling Overview	269
29.1.1 Layer 2 Protocol Tunneling Mode	270
29.2 Configuring Layer 2 Protocol Tunneling	271
IP Application	273
Static Route	275
30.1 Static Routing Overview	275
30.2 Configuring Static Routing	276
Differentiated Services	279
31.1 DiffServ Overview	279
31.1.1 DSCP and Per-Hop Behavior	279
31.1.2 DiffServ Network Example	280
31.2 Two Rate Three Color Marker Traffic Policing	280
31.2.1 TRTCM-Color-blind Mode	281
31.2.2 TRTCM-Color-aware Mode	281
31.3 Activating DiffServ	282
31.3.1 Configuring 2-Rate 3 Color Marker Settings	283
31.4 DSCP-to-IEEE 802.1p Priority Settings	284
31.4.1 Configuring DSCP Settings	285
DHCP	287
32.1 DHCP Overview	287
32.1.1 DHCP Modes	287
32.1.2 DHCP Configuration Options	287
32.2 DHCP Status	288
32.3 DHCP Relay	288
32.3.1 DHCP Relay Agent Information	288
32.3.2 Configuring DHCP Global Relay	289
32.3.3 Global DHCP Relay Configuration Example	290
32.4 Configuring DHCP VLAN Settings	291
32.4.1 Example: DHCP Relay for Two VLANs	293
Management	295
Maintenance	297
33.1 The Maintenance Screen	297
33.2 Load Factory Default	298
33.3 Save Configuration	298
33.4 Reboot System	299
33.5 Firmware Upgrade	299
33.6 Restore a Configuration File	300
33.7 Backup a Configuration File	301
33.8 FTP Command Line	301
33.8.1 Filename Conventions	301
33.8.2 FTP Command Line Procedure	303
33.8.3 GUI-based FTP Clients	303
33.8.4 FTP Restrictions	304
Access Control	305
34.1 Access Control Overview	305
34.2 The Access Control Main Screen	305
34.3 About SNMP	306
34.3.1 SNMP v3 and Security	307
34.3.2 Supported MIBs	307
34.3.3 SNMP Traps	308
34.3.4 Configuring SNMP	312
34.3.5 Configuring SNMP Trap Group	314
34.3.6 Setting Up Login Accounts	315
34.4 SSH Overview	317
34.5 How SSH works	318
34.6 SSH Implementation on the Switch	319
34.6.1 Requirements for Using SSH	319
34.7 Introduction to HTTPS	319
34.8 HTTPS Example	320
34.8.1 Internet Explorer Warning Messages	320
34.8.2 Netscape Navigator Warning Messages	321
34.8.3 The Main Screen	323
34.9 Service Port Access Control	323
34.10 Remote Management	324
Diagnostic	327
35.1 Diagnostic	327
Syslog	329
36.1 Syslog Overview	329
36.2 Syslog Setup	330
36.3 Syslog Server Setup	331
Cluster Management	333
37.1 Cluster Management Status Overview	333
37.2 Cluster Management Status	334
37.2.1 Cluster Member Switch Management	335
37.3 Clustering Management Configuration	338
MAC Table	341
38.1 MAC Table Overview	341
38.2 Viewing the MAC Table	342
ARP Table	345
39.1 ARP Table Overview	345
39.1.1 How ARP Works	345
39.2 Viewing the ARP Table	346
Configure Clone	347
40.1 Configure Clone	348
Troubleshooting & Product Specifications	351
Troubleshooting	353
41.1 Power, Hardware Connections, and LEDs	353
41.2 Switch Access and Login	354
41.3 Switch Configuration	357
Product Specifications	359
Appendices and Index	369
Changing a Fuse	371
Common Services	373
Legal Information	377

Match case Limit results 1 per page

Chapter 11 Static Multicast Forward Setup

MES-3728 User’s Guide

121

The following table describes the labels in this screen.

Table 22

Advanced Application > Static Multicast Forwarding

LABEL

DESCRIPTION

Active

Select this check box to activate your rule. You may temporarily deactivate

a rule without deleting it by clearing this check box.

Name

Type a descriptive name (up to 32 printable ASCII characters) for this

static multicast MAC address forwarding rule. This is for identification only.

MAC Address

Enter a multicast MAC address which identifies the multicast group. The

last binary bit of the first octet pair in a multicast MAC address must be 1.

For example, the first octet pair 00000001 is 01 and 00000011 is 03 in

hexadecimal, so 01:00:5e:00:00:0A and 03:00:5e:00:00:27 are valid

multicast MAC addresses.

VID

You can forward frames with matching destination MAC address to port(s)

within a VLAN group. Enter the ID that identifies the VLAN group here. If

you don’t have a specific target VLAN, enter 1.

Port

Enter the port(s) where frames with destination MAC address that matched

the entry above are forwarded. You can enter multiple ports separated by

(no space) comma (,) or hyphen (-). For example, enter “3-5” for ports 3,

4, and 5. Enter “3,5,7” for ports 3, 5, and 7.

Add

Click

Add

to save your rule to the Switch’s run-time memory. The Switch

loses this rule if it is turned off or loses power, so use the

Save

link on the

top navigation panel to save your changes to the non-volatile memory

when you are done configuring.

Cancel

Click

Cancel

to reset the fields to their last saved values.

Clear

Click

Clear

to begin configuring this screen afresh.

Index

Click an index number to modify a static multicast MAC address rule for

port(s).

Active

This field displays whether a static multicast MAC address forwarding rule

is active (

Yes

) or not (

). You may temporarily deactivate a rule without

deleting it.

Name

This field displays the descriptive name for identification purposes for a

static multicast MAC address-forwarding rule.

MAC Address

This field displays the multicast MAC address that identifies a multicast

group.

VID

This field displays the ID number of a VLAN group to which frames

containing the specified multicast MAC address will be forwarded.

Port

This field displays the port(s) within a identified VLAN group to which

frames containing the specified multicast MAC address will be forwarded.

Delete

Click

Delete

to remove the selected entry from the summary table.

Cancel

Click

Cancel

to clear the

Delete

check boxes.