ZyXEL P-660HN-T1A Support Guide - Page 99

Preparation, Survey on Site

Get ZyXEL P-660HN-T1A PDF manuals and user guides View all ZyXEL P-660HN-T1A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

P-660HN Series Support Notes Site survey can help us overcome these problem and even provide us a map of RF coverage of the facility. Preparation Below are the steps to complete a simple site survey with simple tools. 1. First you will need to obtain a facility diagram, such as blueprints. This is for you to mark and take record on. 2. Visually inspect the facility, walk through the facility to verify the accuracy of the diagram and mark down any large obstacle you see that may effect the RF signal such as metal shelf, metal desk, etc on the diagram. 3. Identify user's area, when doing so ask a question where is wireless coverage needed and where does not, and note and take note on the diagram this is information is needed to determine the number of AP required. 4. Determine the preliminary access point location on the facility diagram base on the service area needed, obstacles, power wall jack considerations. Survey on Site Step 1: With the diagram with all information you gathered in the preparation phase. Now you are ready to make the survey. Step 2: Install an access point at the preliminary location. Step 3: Use a notebook with wireless client installed and run it's utility. An utility will provide information such as connection speed, current used channel, associated rate, link quality, signal strength and etc information as shown in utility below. 99 All contents copyright © 2010 ZyXEL Communications Corporation.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
P-660HN Series Support Notes
99
All contents copyright © 2010 ZyXEL Communications Corporation.
Site survey can help us overcome these problem and even provide us a map
of RF coverage of the facility.
Preparation
Below are the steps to complete a simple site survey with simple tools.
1. First you will need to obtain a facility diagram, such as blueprints. This is
for you to mark and take record on.
2. Visually inspect the facility, walk through the facility to verify the accuracy of
the diagram and mark down any large obstacle you see that may effect the RF
signal such as metal shelf, metal desk, etc on the diagram.
3. Identify user's area, when doing so ask a question where is wireless
coverage needed and where does not, and note and take note on the diagram
this is information is needed to determine the number of AP required.
4. Determine the preliminary access point location on the facility diagram base
on the service area needed, obstacles, power wall jack considerations.
Survey on Site
Step 1: With the diagram with all information you gathered in the preparation
phase. Now you are ready to make the survey.
Step 2: Install an access point at the preliminary location.
Step 3: Use a notebook with wireless client installed and run it's utility. An utility
will provide information such as connection speed, current used channel,
associated rate, link quality, signal strength and etc information as shown in
utility below.