ZyXEL PLA5236 User Guide - Page 13

press 0.5 ~ 3 seconds, within 2, minutes, RESET/ENCRYPT

Get ZyXEL PLA5236 PDF manuals and user guides View all ZyXEL PLA5236 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Chapter 2 The RESET/ENCRYPT Button 1 Press the RESET/ENCRYPT button at the side of your powerline device for 0.5 to 3 seconds. The power ( ) light will blink as the powerline device tries to set up a connection with a new random network name. Figure 3 ENCRYPT Connection Procedure PLA PLA press 0.5 ~ 3 seconds press 0.5 ~ 3 seconds within 2 minutes Note: The RESET/ENCRYPT button's location varies for each Powerline model. Note: Check the lights on the two powerline devices. The power ( ) and HomePlug ( ) lights should be on while the devices are connecting. Wait for about two minutes while your powerline devices connect. If the power ( ) light does not blink when you press RESET/ENCRYPT, you have probably pressed the RESET/ENCRYPT button for too long. Try again, pressing the RESET/ENCRYPT button for 0.5 to 3 seconds. If the HomePlug ( ) lights on both powerline devices do not light up, the powerline devices are not connected. Repeat step 1 in this section. If that doesn't work, see the Troubleshooting in Section 12.3 on page 64 for suggestions. 2 To add more powerline devices to your network, use any powerline device (A or B) you have connected to set up a connection with the powerline devices you want to connect (C and D). 3 Press the RESET/ENCRYPT button on both powerline devices (A and C, or B and C) for 0.5 to 3 seconds to add powerline device C. This must be done within 2 minutes (120 seconds) of pressing the RESET/ ENCRYPT button on the PLA. 4 Press the RESET/ENCRYPT button on both powerline devices (A and D, B and D or C and D) for 0.5 to 3 seconds to add powerline device D. This must be done within 2 minutes (120 seconds) of pressing the RESET/ENCRYPT button on the PLA. PLA5236 User's Guide 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Chapter 2 The RESET/ENCRYPT Button
PLA5236 User’s Guide
13
1
Press the
RESET/ENCRYPT
button at the side of your powerline device for 0.5 to 3 seconds. The power
(
) light will blink as the powerline device tries to set up a connection with a new random network
name.
Figure 3
ENCRYPT Connection Procedure
Note: The
RESET/ENCRYPT
button’s location varies for each Powerline model.
Note: Check the lights on the two powerline devices. The power (
) and HomePlug (
)
lights should be on while the devices are connecting. Wait for about two minutes while
your powerline devices connect.
If the power (
) light does not blink when you press
RESET/ENCRYPT
, you have probably pressed
the
RESET/ENCRYPT
button for too long. Try again, pressing the
RESET/ENCRYPT
button for 0.5 to 3
seconds.
If the HomePlug (
) lights on both powerline devices do not light up, the powerline devices
are not connected. Repeat step 1 in this section. If that doesn’t work, see the Troubleshooting in
Section 12.3 on page 64 for suggestions.
2
To add more powerline devices to your network, use any powerline device (
A
or
B
) you have
connected to set up a connection with the powerline devices you want to connect (
C
and
D
).
3
Press the
RESET/ENCRYPT
button on both powerline devices (
A
and
C
, or
B
and
C
) for 0.5 to 3 seconds to
add powerline device
C
. This must be done within 2 minutes (120 seconds) of pressing the
RESET/
ENCRYPT
button on the PLA.
4
Press the
RESET/ENCRYPT
button on both powerline devices (
A
and
D
,
B
and
D
or
C
and
D
) for 0.5 to 3
seconds to add powerline device
D
. This must be done within 2 minutes (120 seconds) of pressing the
RESET/ENCRYPT
button on the PLA.
press 0.5 ~ 3 seconds
press 0.5 ~ 3 seconds
within 2
minutes
PLA
PLA