ZyXEL U-336E User Manual - Page 71

value in <pgl>, the is

Get ZyXEL U-336E PDF manuals and user guides View all ZyXEL U-336E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Command +FPI="string" +FPR=n +FPS=n +FRQ=pgl,cbl +FSP=n Value Description Local fax station ID string, for polling Rx. Serial port rate control parameter: n=0 Automatic DTE rate detection by the DCE. n>0 Serial rate is fixed at the value multiplied by 2400 bps. For example, when n=8, the DTE rate is equal to 19200 bps (8x2400). Page transfer status: refer to the +FPTS Class 2 command in previous sections for settings. Receiving quality threshold parameters: pgl= Specify the percentage of good lines 0-64 (e.g. with negotiated number of pixels) (HEX required for a page considered value) acceptable. The percentage of good lines would be computed by the equation: 100 x ( - ) / lc: total line count as reported in the +FPS: response. bl: bad line count as reported in the +FPS: response. If the resulting value is less than the value in , the page is unacceptable. cbl= Specify the maximum tolerable number 0-FF of consecutive bad lines. If this value is (HEX exceeded for a given page, the DCE value) shall consider the page unacceptable. Enable polling command: n=0 Disable polling. Fax Operation 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
Fax Operation
59
Command
Value
Description
+FPI=
"string"
Local fax station ID string, for polling
Rx.
+FPR=
n
Serial port rate control parameter:
n=0
Automatic DTE rate detection by the
DCE.
n>0
Serial rate is fixed at the value
multiplied by 2400 bps. For example,
when n=8, the DTE rate is equal to
19200 bps (8x2400).
+FPS=
n
Page transfer status: refer to the +FPTS
Class 2 command in previous sections
for settings.
+FRQ=
pgl,cbl
Receiving quality threshold parameters:
pgl=
0-64
(HEX
value)
Specify the percentage of good lines
(e.g. with negotiated number of pixels)
required for a page considered
acceptable. The percentage of good
lines would be computed by the
equation:
100 x (<lc> - <bl>) / <lc>
lc: total line count as reported in the
+FPS: response.
bl: bad line count as reported in the
+FPS: response.
If the resulting value is less than the
value in <pgl>, the page is
unacceptable.
cbl=
0-FF
(HEX
value)
Specify the maximum tolerable number
of consecutive bad lines. If this value is
exceeded for a given page, the DCE
shall consider the page unacceptable.
+FSP=
n
Enable polling command:
n=0
Disable polling.