ZyXEL U-336E User Manual - Page 78

Flow Control

Get ZyXEL U-336E PDF manuals and user guides View all ZyXEL U-336E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Field DISCONNECT1 P Description Disconnect without remote confirmation. Remote fax number. The basic AT commands ATV0 and ATQ1 do not affect the above CONNECT and DISCONNECT status report result codes. The modem will always return the same status format as above. Flow Control In extended fax AT command mode, the U-336E always uses hardware (CTS/RTS) flow control. The flow control signaling used sending a fax is: • CTS is used by your modem for DTE flow control. When the modem turns CTS off, the buffer inside the modem is full and cannot accept any more data. The computer should send data only when CTS is ON. • RTS is used by the computer to signal your modem that the fax message is finished. As soon as RTS off is detected, the modem starts the post message handshaking to make sure that the remote facsimile has received the fax message successfully. Then it hangs up the phone and sends a status report to the DTE. If you want to send a multi-page fax, just add the RTC signal between the fax message of two pages. The modem detects the RTC signal automatically, handshakes the multi-page procedure with the remote facsimile and sends the next page. The following flow control signaling is used while receiving a fax: • CTS is not used when receiving fax. 66 Fax Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
66
Fax Operation
Field
Description
DISCONNECT1
Disconnect without remote confirmation.
P<string>
Remote fax number.
The basic AT commands ATV0 and ATQ1 do not affect the above
CONNECT and DISCONNECT status report result codes. The
modem will always return the same status format as above.
Flow Control
In extended fax AT command mode, the U-336E always uses
hardware (CTS/RTS) flow control. The flow control signaling used
sending a fax is:
•
CTS is used by your modem for DTE flow control. When the
modem turns CTS off, the buffer inside the modem is full and
cannot accept any more data. The computer should send data
only when CTS is ON.
•
RTS is used by the computer to signal your modem that the fax
message is finished. As soon as RTS off is detected, the modem
starts the post message handshaking to make sure that the
remote facsimile has received the fax message successfully.
Then it hangs up the phone and sends a status report to the
DTE.
If you want to send a multi-page fax, just add the RTC signal
between the fax message of two pages. The modem detects the
RTC signal automatically, handshakes the multi-page procedure
with the remote facsimile and sends the next page.
The following flow control signaling is used while receiving a fax:
•
CTS is not used when receiving fax.