Home » Akai Manuals » Audio Mixers » Akai MPC1000 » Manual Viewer

Akai MPC1000 Operation Manual - Page 79

BAND EQ (4 band equalizer), COMPRESSOR, PHASE SHIFTER, Offset L/R field

Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Effect 4 BAND EQ (4 band equalizer) This effect is the equalizer, which can adjust the 4 frequency bands to correct or process the sound. Low/Hi EQ is a shelving type equalizer, which boosts or cuts the frequencies higher or lower than the specified frequency. The Mid1/2 is a peaking type equalizer, which boosts or cuts the specified frequency and the harmonics surrounding the frequency. Low frq field Low Gain field Mid1 frq field Mid1 Gain field Mid1 Q field Mid2 frq field Mid2 Gain field Mid2 Q field High frq field High Gain field You can set the low frequency range. You can adjust the gain of the low frequency range. You can set the frequency of the mid frequency range 1. You can set the gain of the mid frequency range 1. You can set the band range of the mid frequency range 1. You can set the frequency of the mid frequency range 2. You can set the gain of the mid frequency range 2. You can set the frequency range of the mid frequency range 2. You can set the frequency of the high frequency range. You can set the gain of the high frequency range. COMPRESSOR This effect compresses sound which exceeds a certain level, to make the sound levels even. Threshold field: any signals, which exceed the level set here, will be compressed. The lower the value is, the better the result will be. Gain field Ratio field Attack field Release field You can adjust the overall level here. As you lower the value in the Threshold field, the overall level is also lowered. You can adjust the final level in this field. You can set the compression ratio here. The larger you set the value, the greater the compression becomes and you can make the overall level even. You can set the time it takes to start the compression after the incoming signal exceeds the level set in the Threshold field. You can set the time it takes to finish the compression after the incoming signal falls below the level set in the Threshold field. PHASE SHIFTER This effect adds sounds with different phases to the original sound, to create a swelling or rotating sound. Sweep rate field Offset L/R field Feedback field Sweep width field Mid point field L/R sweep sync field You can set the speed of the modulation here. You can set the amount of the phase shift of L and R. If you set this field to 00, L and R will be in sync. As you increase the value, the phases of the L and R will shift and you can create the complicated effect. You can set the feed back level from the output to the effect input. The effect will be boosted and create more a unique sound. You can set the depth of the modulation here. You can set the center frequency for the phase shift. If you set this value high, the phase shift will be applied around the high frequency range. If you set it to ON, the Sweep rate will be set at the same cycle for both the Left and Right. If you set to OFF, the sweep rate of the right channel will be set slightly higher than that of the left channel. You will be able to create a more complicated effect. -71-

Section	Page
MPC1000	1
Table of contents	6
Chapter 1 : Introduction	9
The user interface	9
Front Panel	11
Rear Panel	11
Connecting MPC1000 to External Audio/MIDI device	12
Terminologies in MPC1000	13
Sequence	13
Track	13
Song	13
Sample	13
Drum Pad	13
Program	14
RAM	14
Memory Card	14
Chapter 2 : Basic Operation	15
MAIN Page	15
Cursor, Cursor Keys, Field, DATA Wheel	15
Function Keys	15
WINDOW key	15
MODE key	16
Setting names	16
Entering letters with DATA wheel	16
Entering letters with a pad	16
Other useful functions in the Name window	17
Copy and Paste function	17
Entering numbers with NUMERIC key	17
Chapter 3 : Sequencer feature	18
MAIN page	18
Recording the performance	18
Playing back a sequence	19
Repeat play back of a sequence	19
Other useful features for recording sequences	20
Undo Sequence feature	20
Erase feature	20
Deleting in real time	20
Deleting in the Erase window	20
Timing correct feature	21
Real time timing correction	21
Swing feature	21
Correcting the timing of recorded events	22
Swing feature	22
Click/Metronome feature	22
Note repeat feature	23
Punch In/Punch Out feature	23
Detailed information on sequence feature	23
Setting the length of a sequence	23
Setting the time signature of the sequence	24
Setting tempo	24
Tap tempo feature	24
Changing tempo of all sequences at one time	24
About Tempo change	25
Setting the loop for a sequence	25
Extending the sequence length automatically	25
Changing the default settings	26
Changing the sequence name	26
Changing the default name for a sequence	26
Copying a sequence	26
Deleting a sequence	27
Deleting all sequences	27
Handling the duration (the length of a note) at the loop boundary	27
Track features	28
Setting the track type	28
Selecting a program	28
Track mute feature	28
Setting the MIDI Output channel	28
Changing a track name	28
Changing the default name for a track	29
Copying a track	29
Deleting a track	29
Deleting all tracks	29
Selecting a track with function keys	30
Solo function of a track	30
MIDI sequencer features	30
About MIDI...	30
About MIDI sequencer	30
Handling the sustain pedal	32
Chapter 4 : Editing sequences	33
Selecting a region within a track to edit	33
Selecting a region for the editing	33
Setting the time	33
Setting the pad/note number	33
Copying events (COPY)	34
Moving events (MOVE)	34
Changing the key of the event (TRANSPOSE)	35
Selecting the editing region by bar	35
Copying bars (COPY)	35
Inserting a bar (INSERT)	36
Deleting a bar (DELETE)	36
Changing the order of tracks (TRACK MOVE)	37
Chapter 5 : Step editing	38
About step edit	38
Screens	38
Basic operation	38
Events	39
Pad event	39
Tempo change event	40
Effect select event	40
Note event	40
Pitch bend event	40
Control change event	40
Program change event	41
Channel pressure event	41
Poly pressure event	41
Exclusive data event	41
Copying/pasting an event	41
Deleting an event	42
Entering an event (Step recording)	42
Detailed setting for step recording	42
Inserting an event	43
Chapter 6 : Song mode	44
Structure of a song	44
Screens	44
Creating a song	45
Deleting a step	45
Inserting a step	45
Playing a song	45
Other features in the SONG mode	46
Changing the song name	46
Copying a song	46
Deleting a song	46
Deleting all the songs	46
Setting all sequences to the same tempo	47
Ignoring tempo change events in a sequence	47
Converting a song to a sequence	47
Chapter 7 : Functions of a pad	48
Playing with pads	48
Switching pad banks	48
Full level function (FULL LEVEL key)	48
16 level function (16LEVELS key)	48
Setting the track mute with pads	49
TRACK MUTE Screen	49
Solo function	49
Setting the track mute in solo mode	49
Selecting a sequence to play with pads	50
NEXT SEQ Screens	50
SUDDEN key	50
HOLD key	51
Chapter 8 : Q-Link slider	52
Setting the slider	52
Recording the slider value in a sequence	52
AFTER key	52
Chapter 9 : Using the MPC1000 with external devices	53
Sync with the MPC1000 as the master	53
Sync with the MPC1000 as the slave	53
Connecting the MPC1000 to the MIDI keyboard with the sound module	54
Setting the MIDI input	55
Chapter 10 : Recording a sample	56
Preparing the recording	56
Starting the recording	57
Recording the sample - detailed information	58
Recording the digital signal	58
Preparing the recording	58
Recording the MAIN OUT	58
Preparing the recording	58
Other features	59
Monitoring feature	59
Peak hold/Reset peak feature	59
Sample Memory Window	59
Chapter 11 : Editing a sample	60
Setting the start/end points for the sample	60
About the waveform display	60
Adjusting the start point	60
Adjusting the end point	61
Zooming in/out of the waveform	61
LINEAR and LOGARITHMIC displays	61
Deleting an unnecessary part from a sample (DISCARD)	61
Saving part of a sample as a new sample (EXTRACT)	62
Sample window features	62
Changing the sample name	62
Changing the pitch of a sample	62
Copying a sample	63
Deleting a sample	63
Deleting all samples	63
Other editing functions	63
NORMALIZE	63
Setting the loop	64
Adjusting the loop point	64
Adjusting the end point	64
Zooming in/out of the waveform	65
LINEAR and LOGARITHMIC displays	65
Linking the loop point to the start point	65
Chapter 12 : Program	66
Creating a program	66
Assigning/Reassigning samples to the pads	66
Playing the sample while the pad is being hit	67
Setting the volume and the tuning for a sample	67
Changing the sample volume with velocity	67
Playing several samples with one pad	68
Switching between samples using velocity	68
Setting the envelope for a pad	69
The functions in the Program window	69
Changing the program name	69
Copying a program	70
Deleting a program	70
Deleting all programs	70
Setting the program change number	70
Editing the sound of a sample	71
Linking the two filters	71
Controlling the sound with velocity	72
Simulating the open/close hi-hat (setting the mute group)	72
Setting the overlap of the sounds on the same pad (voice overlap)	72
Delete all the unused samples at the same time (PURGE)	73
Setting a MIDI note number to the pads	73
Assigning MIDI note numbers to the pads (changing the default setting)	74
Chapter 13 : Mixer	75
Setting the level and pan of the pad	75
Setting the output for the sample	75
Selecting the pad to apply the effect	76
Chapter 14 : Effect	77
Applying effects to a specific pad sound	77
Applying reverb	78
Applying effects of the FX2 to the effect sound of the FX1	78
Editing effects	78
BIT GRUNGER	78
4 BAND EQ (4 band equalizer)	79
COMPRESSOR	79
PHASE SHIFTER	79
TREMOLO	80
FLYING PAN	80
REVERB	80
CHORUS and FLANGER	80
Using the master effect	81
Editing the master effects	81
Editing the effect set	82
Changing the name of the effect set	82
Copying the effect set	82
Resetting the effect set	82
Chapter 15 : Save / Load	83
Saving the data	83
Selecting the destination	83
Creating a new folder	84
Saving a sample	84
Saving a program	84
Saving all the programs and the samples at the same time	85
Saving a sequence	85
Saving all the sequences and the songs at the same time	86
Saving all the data in the memory at the same time	86
Creating the Autoload folder	87
Loading a file	87
Selecting a file	87
Loading a sample	88
Loading a program	88
Loading a sequence	89
Loading the ALL file	89
Loading an individual sequence from the ALL file	89
Loading only the effect set from the ALL file	90
Loading a folder	90
Loading a project	90
Renaming a file	91
Deleting a file	91
Setting the auto load function	91
Formatting the memory card	92
Saving the data to the internal flash memory	92
When SAVE ALL SEQS & SONGS is selected	92
When SAVE ALL PROGRAMS &SAMPLES is selected	92
Chapter 16 : Connecting the MPC1000 to your computer	93
Connecting the MPC1000 to a Windows-based PC	93
Connecting the MPC1000 to the Macintosh	94
Chapter 17 : Other settings	95
Foot switch	95
Adjusting the master level	96
Adjusting the contrast of LCD	96
Initialize to Factory Preset	96
Appendix	97
Index	97
Specifications	99
MIDI Implementation Chart	101

Match case Limit results 1 per page

4 BAND EQ (4 band equalizer)

This effect is the equalizer, which can adjust the 4 frequency bands to correct or process the sound.

Low/Hi EQ is a shelving type equalizer, which boosts or cuts the frequencies higher or lower than the specified

frequency.

The Mid1/2 is a peaking type equalizer, which boosts or cuts the specified frequency and the harmonics

surrounding the frequency.

Low frq field

You can set the low frequency range.

Low Gain field

You can adjust the gain of the low frequency range.

Mid1 frq field

You can set the frequency of the mid frequency range 1.

Mid1 Gain field

You can set the gain of the mid frequency range 1.

Mid1 Q field

You can set the band range of the mid frequency range 1.

Mid2 frq field

You can set the frequency of the mid frequency range 2.

Mid2 Gain field

You can set the gain of the mid frequency range 2.

Mid2 Q field

You can set the frequency range of the mid frequency range 2.

High frq field

You can set the frequency of the high frequency range.

High Gain field

You can set the gain of the high frequency range.

COMPRESSOR

This effect compresses sound which exceeds a certain level, to make the sound levels even.

Threshold field: any signals, which exceed the level set here, will be compressed. The lower the value is, the

better the result will be.

Gain field

You can adjust the overall level here. As you lower the value in the Threshold field, the

overall level is also lowered. You can adjust the final level in this field.

Ratio field

You can set the compression ratio here. The larger you set the value, the greater the

compression becomes and you can make the overall level even.

Attack field

You can set the time it takes to start the compression after the incoming signal

exceeds the level set in the Threshold field.

Release field

You can set the time it takes to finish the compression after the incoming signal falls

below the level set in the Threshold field.

PHASE SHIFTER

This effect adds sounds with different phases to the original sound, to create a swelling or rotating sound.

Sweep rate field

You can set the speed of the modulation here.

Offset L/R field

You can set the amount of the phase shift of L and R. If you set this field to 00, L and R

will be in sync. As you increase the value, the phases of the L and R will shift and you

can create the complicated effect.

Feedback field

You can set the feed back level from the output to the effect input. The effect will be

boosted and create more a unique sound.

Sweep width field

You can set the depth of the modulation here.

Mid point field

You can set the center frequency for the phase shift. If you set this value high, the

phase shift will be applied around the high frequency range.

L/R sweep sync field

If you set it to ON, the Sweep rate will be set at the same cycle for both the Left and

Right. If you set to OFF, the sweep rate of the right channel will be set slightly higher

than that of the left channel. You will be able to create a more complicated effect.

Effect

-71-