Apple M8840LL/A Setup Guide - Page 43

If you're installing a 1.6-inch SCSI drive in the carrier

Get Apple M8840LL/A - Power Mac - G4 PDF manuals and user guides
UPC - 718908440841
View all Apple M8840LL/A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

m If you're installing a second ATA drive in drive position 3: m With the connectors facing you, attach the screws to the right side of the carrier. m Insert and tighten the screws on the left side until the tab bends slightly inward. m If you're attaching a 1.0-inch drive to an empty carrier in drive position 3, insert the screws through the bottom of the carrier. m If you're installing a 1.6-inch SCSI drive in the carrier, attach it with screws through the carrier's lower side holes, as shown on the right side of the illustration. Note: The tinted screws illustrated below indicate the four screws that came in the computer's accessory kit. Use them where shown. Where untinted screws are shown, use the screws that came with the new drive. Attach an additional ATA drive (1" high) to the upper portion of the drive carrier by screwing it into position on its sides. Attach the two screws on this side first. Attach an additional SCSI drive (1.6" high) to the lower portion of the drive carrier by screwing it into position on its sides. These two tabs will bend inward as you tighten these two screws. ATA or SCSI drives that are 1" high are attached to the lower portion of the drive carrier from the bottom. Position the hard disk drive on the drive carrier so that the ribbon cable connector and the power cord connector are accessible. Working Inside the Computer 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Working Inside the Computer
43
m
If you’re installing a second ATA drive in drive position 3:
m
With the connectors facing you, attach the screws to the right side of the carrier.
m
Insert and tighten the screws on the left side until the tab bends slightly inward.
m
If you’re attaching a 1.0-inch drive to an empty carrier in drive position 3,
insert the
screws through the bottom of the carrier.
m
If you’re installing a 1.6-inch SCSI drive in the carrier,
attach it with screws through the
carrier’s lower side holes, as shown on the right side of the illustration.
Note:
The tinted screws illustrated below indicate the four screws that came in the
computer’s accessory kit. Use them where shown. Where untinted screws are shown, use
the screws that came with the new drive.
Attach an additional SCSI drive (1.6" high)
to the lower portion of the drive carrier
by screwing it into position on its sides.
Attach an additional ATA drive (1" high)
to the upper portion of the drive carrier
by screwing it into position on its sides.
Attach the two screws on this side first.
These two
tabs will
bend
inward as
you tighten
these two
screws.
ATA or SCSI drives
that are 1" high are
attached to the lower
portion of the drive
carrier from the bottom.
Position the hard disk drive on the drive carrier so that the ribbon cable connector
and the power cord connector are accessible.