Asus VIA User Manual - Page 37

pin PWR_FAN, CHA_FAN, F_FAN, CPU_FAN

Get Asus VIA PDF manuals and user guides View all Asus VIA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

3. HARDWARE SETUP 14) Power Supply, CPU, Chassis Fan Connectors (3-pin PWR_FAN, CHA_FAN, F_FAN, CPU_FAN) These connectors support cooling fans of 350mA (4.2 Watts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of the connector. NOTE: The "Rotation" signal is to be used only by a specially designed fan with rotation signal. The Rotations per Minute (RPM) can be monitored using ASUS PC Probe (see 6. SOFTWARE REFERENCE). The Rotation signal is not supported by F-FAN. WARNING! The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers, do not place jumper caps over these pins. PWR_FAN CHA_FAN GND +12V Rotation 01 01 01 GND +12V Rotation F_FAN A7V A7V 12-Volt Cooling Fan Power NC +12V GND Rotation +12V GND CPU_FAN 3. H/W SETUP Connectors ASUS A7V User's Manual 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
ASUS A7V User’s Manual
37
3. HARDWARE SETUP
Connectors
3. H/W SETUP
14) Power Supply, CPU, Chassis Fan Connectors
(3-pin PWR_FAN, CHA_FAN, F_FAN, CPU_FAN)
These connectors support cooling fans of 350mA (4.2 Watts) or less. Orientate
the fans so that the heat sink fins allow airflow to go across the onboard heat
sink(s) instead of the expansion slots. Depending on the fan manufacturer, the
wiring and plug may be different. The red wire should be positive, while the
black should be ground. Connect the fan’s plug to the board taking into consid-
eration the polarity of the connector.
NOTE:
The “Rotation” signal is to be used only by a specially designed fan with
rotation signal. The Rotations per Minute (RPM) can be monitored using ASUS PC
Probe (see
6. SOFTWARE REFERENCE
). The Rotation signal is
not supported
by F-FAN.
WARNING!
The CPU and/or motherboard will overheat if there is no airflow
across the CPU and onboard heatsinks.
Damage may occur to the motherboard
and/or the CPU fan if these pins are incorrectly used.
These are not jumpers,
do not place jumper caps over these pins.
A7V 12-Volt Cooling Fan Power
CHA_FAN
GND
Rotation
+12V
F_FAN
GND
NC
+12V
GND
Rotation
+12V
CPU_FAN
PWR_FAN
GND
Rotation
+12V
0
1
0
1
0
1
A7V