Brother International KE-430D Instruction Manual - English - Page 23

Connecting the cords, INSTALLATION, < Main P. C. board &gt

Get Brother International KE-430D PDF manuals and user guides View all Brother International KE-430D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

3-10. Connecting the cords < Main P. C. board > 3. INSTALLATION 1. Gently tilt back the machine head. 2. Pass the cord bundle through the hole in the work table. 3. Loosen the two screws (1), and then open the cord presser plate (2) in the direction of the white arrow and pass the cord bundle through the opening. 4. Securely connect the connectors as indicated in the table below. Note: • Check that the connector is facing the correct way, and then insert it firmly until it locks into place. • Secure the cables with cable ties and cord clamps, while being careful not to pull on the connector. 4412Q Lock the cord clamp securely. 4413Q Connectors X pulse motor encoder [5-pin] White Y pulse motor encoder [5-pin] Blue Work clamp encoder [5-pin] Black Foot switch [10-pin] Operation panel [8-pin] Machine head switch [3-pin] Thread clamp sensor [6-pin] Connection location on main P. C. board P2 (X-ENC) P3 (Y-ENC) P4 (P-ENC) P5 (FOOT) P6 (PANEL) P8 (HEAD-SW) P12 (TPK-SEN) Cord clamps (3) (3) (3) (3) (3) (4) (4), (5) KE-430D, BE-438D 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
3. INSTALLATION
16
KE-430D, BE-438D
3-10. Connecting the cords
1. Gently tilt back the machine head.
2. Pass the cord bundle through the hole
in the work table.
3. Loosen the two screws (1), and then
open the cord presser plate (2) in the
direction of the white arrow and pass
the cord bundle through the opening.
4. Securely connect the connectors as
indicated in the table below.
Note:
• Check that the connector is facing
the correct way, and then insert it
firmly until it locks into place.
• Secure the cables with cable ties
and cord clamps, while being careful
not to pull on the connector.
< Main P. C. board >
Connectors
Connection location on
main P. C. board
Cord clamps
X pulse motor encoder [5-pin] White
P2 (X-ENC)
(3)
Y pulse motor encoder [5-pin] Blue
P3 (Y-ENC)
(3)
Work clamp encoder [5-pin] Black
P4 (P-ENC)
(3)
Foot switch [10-pin]
P5 (FOOT)
(3)
Operation panel [8-pin]
P6 (PANEL)
(3)
Machine head switch [3-pin]
P8 (HEAD-SW)
(4)
Thread clamp sensor [6-pin]
P12 (TPK-SEN)
(4), (5)
4413Q
Lock the cord
clamp securely.
4412Q