Campbell Scientific CSAT3 CSAT3 3-D Sonic Anemometer - Page 12

Initial Setup

Get Campbell Scientific CSAT3 PDF manuals and user guides View all Campbell Scientific CSAT3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

CSAT3 Three Dimensional Sonic Anemometer 2.4 Power Requirements VOLTAGE SUPPLY: 10 to 16 Vdc POWER: 2.4 W @ 60 Hz measurement frequency 1.2 W @ 20 Hz measurement frequency 3. Initial Setup 3.1 Factory Settings • Analog Outputs - Off • Execution Parameter - 10 Hz (see Section 10.3 and B.1) • Trigger Source - Internal Clock (see Section 8, 9, and B.1) • SDM Address - 3 (see Section 3.2, 6.1, and 10.3) • RS-232 baud rate - 9600 bps (RS=0) (see Section 12 and Appendix B) • Software RTS - Off (RI=0) (see Section 12 and Appendix B) • Unprompted Output - Off (&=0) (see Appendix B) The above settings can be changed with a PC, running the CSAT3 PC support software (CSAT32.EXE), and the RS-232 cable. A copy of the CSAT3 PC support software is available from the Campbell Scientific web site in the Support|Downloads section. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
CSAT3 Three Dimensional Sonic Anemometer
2.4
Power Requirements
VOLTAGE SUPPLY:
10 to 16 Vdc
POWER:
2.4 W @ 60 Hz measurement frequency
1.2 W @ 20 Hz measurement frequency
3.
Initial Setup
3.1
Factory Settings
•
Analog Outputs – Off
•
Execution Parameter – 10 Hz (see Section 10.3 and B.1)
•
Trigger Source – Internal Clock (see Section 8, 9, and B.1)
•
SDM Address – 3 (see Section 3.2, 6.1, and 10.3)
•
RS-232 baud rate – 9600 bps (RS=0) (see Section 12 and Appendix B)
•
Software RTS – Off (RI=0) (see Section 12 and Appendix B)
•
Unprompted Output – Off (&=0) (see Appendix B)
The above settings can be changed with a PC, running the CSAT3 PC support
software (CSAT32.EXE), and the RS-232 cable.
A copy of the CSAT3 PC support
software is available from the Campbell Scientific web site in the Support|Downloads
section.
4